FORTINET FortiGate 1500G Series DDoS Attack Mitigation Appliances User Guide
- June 12, 2024
- FORTINET
Table of Contents
FortiGate 1500G Series DDoS Attack Mitigation
Appliances
FortiGate
1500G Series
FG-1500G and FG-1501G
QuickStart Guide
FortiGate 1500G Series DDoS Attack Mitigation Appliances
This guide covers: FG-1500G and FG-1501G
December 8, 2022
Copyright© 2022 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®,
FortiCare® and FortiGuard®, and certain other marks are registered trademarks
of Fortinet, Inc., in the U.S. and other jurisdictions, and other Fortinet
names herein may also be registered and/or common law trademarks of Fortinet.
All other product or company names may be trademarks of their respective
owners. Performance and other metrics contained herein were attained in
internal lab tests under ideal conditions, and actual performance and other
results may vary. Network variables, different network environments and other
conditions may affect performance results. Nothing herein represents any
binding commitment by Fortinet, and Fortinet disclaims all warranties, whether
express or implied, except to the extent Fortinet enters a binding written
contract, signed by Fortinet’s General Counsel, with a purchaser that
expressly warrants that the identified product will perform according to
certain expressly-identified performance metrics and, in such event, only the
specific performance metrics expressly identified in such binding written
contract shall be binding on Fortinet. For absolute clarity, any such warranty
will be limited to performance in the same ideal conditions as in Fortinet’s
internal lab tests. In no event does Fortinet make any commitment related to
future deliverables, features or development, and circumstances may change
such that any forward-looking statements herein are not accurate. Fortinet
disclaims in full any covenants, representations, and guarantees pursuant
hereto, whether express or implied. Fortinet reserves the right to change,
modify, transfer, or otherwise revise this publication without notice, and the
most current version of the publication shall be applicable.
For Product License Agreement / EULA and Warranty Terms, visit
https://www.fortinet.com/content/dam/fortinet/assets/legal/EULA.pdf
Before you begin
Register your device to access FortiGuard updates, cloud management, firmware
upgrades, technical support and warranty coverage.
http://support.fortinet.com
The Essentials
Default Logins
| https://192.168.1.99
Username: admin
Password: leave blank
MGMT IP is 192.168.1.99
---|---
Admin Guide
For a detailed Getting Started guide, setup and configuration information,
refer to the Admin Guide on https://docs.fortinet.com/
Customer Service
For contracts, licensing, product registration and account management, contact
FortiCare Support at https://www.fortinet.com/support/contact
Self-service Resources
Access our knowledge base, forums, videos and technical experts at
https://www.fortinet.com/support/support-services/forticare-support
Thank you for choosing Fortinet
Package Contents
FortiGate 1500G Series
FG-1500G and FG-1501G
Setup Options
Set up your Fortinet device locally or connect using forticloud.com
GUI
Note: For static IP
configuration, use 192.168.1.1 with subnet mask
255.255.255.0
CLI
Note: For a detailed CLI
guide, visit docs.fortinet.com
SFP Modules
Installation
Removal
Desktop Installation
Note: Place
the device on a flat, clean and stable surface.
Rack Mount
Note: The
recommended clearance is 1.5 inches above and below the device.
Caution: To avoid personal injury or damage to the device, it is
recommended that two or more people mount the device on a rack.
FG-1500G Series Front Panel
-
STATUS
Green: Normal operation
Flashing Green: Booting up
Red: Major alarm
Off: Device is off
ALARM
Red: Major alarm detected
Amber: Minor alarm detected
Off: No errors detected
HA
Green: Operating in an HA cluster
Red: HA failure
Off: HA disabled
POWER
Green: Device is on
Off: Device is off -
USB x2 (USB A)
USB 3.0 server port -
Console (RJ45)
CLI interface -
HA (RJ45)
LINK/ACT
Green: On, Link up
Flashing Green: Data activity
Off: No link established
SPEED
Green: Linked at 2.5 Gbps
Amber: Linked at 1G/100 Mbps
Off: Linked at 10 Mbps or no link established
SMGMT (RJ45)
LINK/ACT
Green: On, Link up
Flashing Green: Data activity
Off: No link established
SPEED
Green: Linked at 1 Gbps
Amber: Linked at 100 Mbps
Off: Linked at 10 Mbps or no link established
-
Ports 1 to 16 (RJ45)
LINK/ACT
Green: Link established
Flashing Green: Data activity
Off: No link established
SPEED
Green: Connected at 1000 Mbps
Amber: Connected at 100 Mbps
Off: Connected at 10 Mbps or not in use -
Ports 17 to 24 (SFP)
Green: Connected at 1 Gbps
Flashing Green: Data activity
Off: No link established
-
Ports X1 to X4 (SFP+) X1 and X2 are Forti Link ports
Green: Connected at 10/1 Gbps
Flashing Green: Data activity
Off: No link established -
Ultra Low Latency Ports X5 to X8 (SFP28)
Green: Connected at 25/10 Gbps
Flashing Green: Data activity
Off: No link established
FG-1500G Series Rear Panel
FG-1500G-DC Series Rear Panel
DC Models
Only (FG-1500G-DC and FG-1501G-DC)
This product is only intended for installation and use in a Restricted Access
Location. The DC power cables are intended to be used only for in-rack wiring,
must be routed away from sharp edges, and must be adequately fixed to prevent
excessive strain on the wires and terminals.
DC cables must be a minimum of 12 AWG.
For DC Cables Installation , ensure the terminal rings are securely and
safely fastened to the PSU terminals.
-
Power Supply for FG-1500G and FG-1501G
100-240VAC, 50/60Hz, 6A Max (2x PSU) 1+1 Redundant, hot-swappable power supplies -
Input LED Indicators
Green: Input voltage within normal range
Flashing Green: Over or under voltage warning
Off: No input power -
Output LED Indicators
Green: Output voltage normal
Flashing Green: Standby mode
Flashing Amber: Warning
Amber: Critical error
Off: No output
- Power Supply for FG-1500G-DC and FG-1501G-DC
-48V DC to -60V DC, 7A, hot swappable, redundant (1+1) power supplies
Cautions and Warnings
Environmental specifications
Ambient operating temperature: 0°C to 40°C
Rack Mount Instructions – The following or similar rack-mount
instructions are included with the installation instructions:
Elevated Operating Ambient – If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow – Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mechanical Loading – Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading – Consideration should be given to the connection of
the equipment to the supply circuit and the effect that overloading of the
circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Reliable Earthing – Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other
than direct connections to the branch circuit (e.g. use of power strips).
Refer to specific Product Model Data Sheet for Environmental Specifications (Operating Temperature, Storage Temperature, Humidity, and Altitude)
Safety
Moving parts — Hazardous moving parts. Keep away from moving fan blades.
Warning: Equipment intended for installation in Restricted Access
Location.
Warning : A readily accessible disconnect device shall be incorporated in
the building installation wiring.
Warning : A UL Listed external disconnect device, i.e. circuit breaker or
other, with over current protection suitable for local code (rated 6A
recommended) shall be installed with this equipment
Battery – Risk of explosion if the battery is replaced by an incorrect
type. Do not dispose of batteries in a fire. They may explode. Dispose of used
batteries according to your local regulations.
IMPORTANT: Switzerland: Annex 4.10 of SR814.013 applies to batteries.
CAUTION: Shock Hazard. Disconnect all power sources.
Grounding — To prevent damage to your equipment, connections that enter
from outside the building should pass through a lightning / surge protector,
and be properly grounded. Use an electrostatic discharge workstation (ESD)
and/or wear an anti-static wrist strap while you work. In addition to the
grounding terminal of the plug, on the back panel, there is another, separate
terminal for earthing.
Caution : Slide/rail mounted equipment is not to be used as a shelf or a
work space.
The rack may tip over causing serious personal injury.
Before extending the rack to the installation position, read the installation
instructions.
Do not put any load on the slide-rail mounted equipment in the installation
position.
Do not leave the slide-rail mounted equipment in the installation position.
Laser Class 1 optical transceiver shall be used only
IEC 60825-1:2014 transfer to FDA/CDRH Complies with FDA performance standards
for laser products except for conformance with IEC 60825-1 Ed.3., as described
in Laser Notice No. 56, dated May 8, 2019.
The SFP ports should use UL Listed Optional Transceiver product, Rated 3.3Vdc,
Laser Class 1.
Fiber optic transceiver must be rated 3.3V, 22mA max, Laser Class 1, UL
certified component.
Warning: Class I Equipment. This equipment must be earthed. The power
plug must be connected to a properly wired earth ground socket outlet. An
improperly wired socket outlet could place hazardous voltage on accessible
metal parts.
Warning: All Ethernet cables are designed for intra-building connection
to other equipment. Do not connect these ports directly to communication
wiring or other wiring that exits the building where the appliance is located.
Regulatory Notices
Federal Communication Commission (FCC) – USA
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received; including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
WARNING: Any changes or modifications to this product not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Industry Canada Equipment Standard for Digital Equipment (ICES) – Canada
CAN ICES-003 (A) / NMB-003 (A)
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communications.
Innovation, Science and Economic Development (ISED) – Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licenceexempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This radio transmitter (Contains IC:7280B-111T15D) has been approved by ISED
to operate with the antenna types listed below with the maximum permissible
gain and required antenna impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures.
Ant.| Brand Holder| Model Name| Antenna Type|
Connector| Antenna Gain (dBi)
---|---|---|---|---|---
1| Wieson| ARY196-0346-005-00| PIFA| Ipex I| 1.82
2| INPAQ| WA-F-LA-02-114| PIFA| Ipex I| 0.73
European Conformity (CE) – EU
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
The product transmits within the frequency ranges and less than or equal to
the power listed below: 2402-2480MHz less than 20dBm
Simplified EU Declaration of Conformity
This declaration is only valid for Fortinet products (including combinations
of software, firmware and hardware) provided by Fortinet or Fortinet’s
authorized partners to the end-customer directly for use within the EU or
countries that have implemented the EU Directives and/or spectrum regulation.
Any Fortinet products not obtained directly from Fortinet or Fortinet’s
authorized partners may not comply with EU Directives and Fortinet makes no
assurances for such products.
This product is in compliance with Directive 2014/53/EU.
Note: The full Declaration of Conformity for this product is available in
the link below: https://site.fortinet.com/ProductRegulatory/EU
Compliance with 2014/53/EU Radio Equipment Directive (RED)
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table
provides information on the frequency bands used and the maximum e.i.r.p. of
the product for sale in the EU:
| Frequency Range (MHz) | Maximum e.i.r.p. (dBm) |
|---|---|
| Bluetooth 2.4GHz | 4. |
UK Conformity Assessed (UKCA) – United Kingdom
The product transmits within the frequency ranges and less than or equal to
the power listed below: 2402-2480MHz less than 20dBm
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This product is in compliance with Statutory Instrument 1206 Radio Equipment
Regulations 2017
The full Declaration of Conformity for this product is available in the link
below: https://site.fortinet.com/ProductRegulatory/UK
Fortinet.com
FG-1500G-ACDC-QSG-20221208.indd 20
2022-12-08 12:02:03 PM
References
- Global Leader of Cybersecurity Solutions and Services | Fortinet
- Welcome
- Global Leader of Cybersecurity Solutions and Services | Fortinet
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>