Antari SW-250 Snow Machine User Manual

**Antari SW-250 Snow Machine User Manual

**

Introduction

Please read all the user manual before operating the machine, and place the manual where the user can refer to it at all time. The manual includes how to install and operate the machine under safe condition and explain all the labels printed on the machine. If you encounter any problem, contact your local Antari dealer for assistant immediately.

Safety Information

DANGER| If the danger is not avoided, it will cause death or serious injury
---|---
WARNING| If the warning is not heeded, it can cause death or serious injury.
CAUTION| If the precaution is not taken, it may cause minor or moderate injury.

DANGER

• Must connect the machine to the correct rated voltage or it might lead to an electrical shock or a burn and may cause serious consequences.
• Must connect the machine to a protected circuit and ensure it is properly grounded to avoid the risk of electrocution. For grounding instruction, please refer to Appendix I on page 18.
• Do not operate the machine with a bundled power cord, it could lead to a fire hazard.
• When operating the machine, do not point at people, animals, or fire.

WARNING

• Please operate the machine on a flat, level hard and well ventilated surface area, reserve at least 50cm space around the machine and make sure there is no flammable gas or material nearby.
• Do not disassemble, repair or modify the machine, it may cause damages, malfunction, risk of electrical shock or result in fire.
• The machine can only be operated by adults or professionals, is not intended for use by person with reduced physical sensory, mental capabilities, or lack of experience and knowledge including children.
• Do not leave the machine running unattended, make sure all powers are off when leaving.
• Children should be supervised to ensure that they do not play with the machine.
• Do not use the machine upside down or tilt it, it might cause damages or malfunction.
• Please store the fluid inside in a well ventilated area without direct sunlight and keep out of reach of children. In case of eye contact or accidentally swallow the fluid, please seek medical attention immediately

CAUTION

• Keep the machine dry at all time. The machine is not waterproof, do not expose the machine to water, rain, or moisture environment.
• Please make sure the power outlet is not damaged or loose before plug in the power cord.
• If the power cord is damaged, it must be replaced by Antari or its local dealers, otherwise the warranty will be void.
• Before operating the machine, please sure the fluid is filled in the fluid tank to avoid the pump in idling state which could lead to overheat or malfunction.
• Before transporting the machine, please make sure the fluid is drained and tank is empty. (Recommend using original package)
• The machine is for indoor use only.
• Do not operate the machine in any area with unstable voltage.
• If you experience strange sound or malfunction, turn off the power and unplug the power cord immediately and contact your local Antari dealer for assistant.
• Do not contact any moving part.
• Only use accessories recommended or sold by Antari.
• Please make sure the power is off when not using the machine and unplug the power cord if not intend to use for a long period of time.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Unplug from outlet before servicing or cleaning.
• Do not operate the machine with a damaged cord or plug, or after the machine malfunctions or is dropped or damaged in any manner. Return machine to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.

Before operating the machine, please read all warning labels on the machine, description as below:

Rear Cover Printing

WARNING!
DISCONNECT POWER BEFORE CHANGING FUSE.
USE ONLY WITH ADULT SUPERVISION.
DO NOT OPERATE WITHOUT LIQUID.
FOR INDOOR USE ONLY. KEEP DRY.
NO USER SERVICEABLE PARTS INSIDE.

Package Contents & Inspection

Package Contents & Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to ensure it is the correct model and all parts are included. If any part appears to be damaged or missing during transportation, please contact your local dealer and return in original package for inspection.

Package Contents

Optional Accessories

Machine Details

Technical Label Information

Please read the technical label information on the back of the machine before operating it.

1. Model Name| 5. Breaker/Fuse
2. Input Voltage| 6. QR CODE for User Manual
3. Frequency| 7. Serial No.
4. Rated Power|

Snow Fluid

CAUTION
Always turn off the power before filling the fluid tank. Do not add flammable liquid to the fluid tank. If fluid gets inside the machine, please contact your local Antari dealer for assistant.

• Only the snow fluid manufactured by Antari can be used, do not mix or dilute the snow fluid.
• The machine is tested and calibrated with the specific snow fluid to get the best performance.
• Please empty the fluid in the tank before switching to another fluid to avoid mixing.
• The warranty on your snow machine will be void if you use snow fluid not manufactured by Antari.

Setting and Manual Operation

WARNING
Machine falling off might cause serious injury, please make sure it is secure and firm on the overhead.

• Step 1. Place the machine on a flat, level hard and well ventilated surface area and reserve at least 50cm open space around the machine, and make sure there is no flammable gas or material nearby;
• Step 2. Fill the fluid tank with Antari approved snow fluid;
• Step 3. Connect the machine to the power outlet. Please read the technical label on the back of the machine and make sure the power outlet is the correspond to the rated voltage for the machine;
• Step 4. When the machine is ready, the LCD display will show “Ready to Snow”;
• Step 5. To start making snow in Timer Mode, press [TIMER] and press [STOP] to stop; this will run based on “interval” & “duration” setting in the main menu;
• Step 6. Or to start making snow in Volume Mod, press [VOLUME] and press [STOP] to stop; you can adjust the volume by pressing [UP] and [DOWN];
• Step 7. To turn off the power, please make sure the machine is not operating. If you will not use the machine a long period of time, please unplug the power cord.

Control Settings

SW-250 Wireless Snow Machine/SW-250 Snow Machine can be operated in the following modes. The machine can only accept 1 type of signal at a time. When using different control modes at the same time, the machine will work according to built-in control priority:

• Manual
• Timer
• DMX512
• Wireless
• Cable Remote

Control Panel Description

SW-250 Wireless Snow Machine/SW-250X Snow Machine can be operated with the onboard digital control

MENU| Press| To enter setting menu

UP| Press| Increase value

DOWN| Press| Decrease value

TIMER| Press| 1.     Press to start making snow according to the set time

2.     Press stop to stop making snow

VOLUME| Press| 1.      Press to start making snow according to set volume output

2.      Press stop to stop making snow

STOP| Press| Stop / Return

Menu Options Description

DMX Connection

DMX Connector Pin Assignment

The machine has a XLR 5-Pin for DMX connection. The diagram below indicates pin assignment information.

The cap on the DMX IN port is a protection cover.
Please remove it with your finger before operation.

DMX Setting

SC-2 Cable Remote (Optional)

SC-2 Cable Remote is an optional accessory for SW-250 Wireless Snow Machine /SW-250X Snow Machine, please see instruction below;

1. Plug the timer cable remote to the connector on the back of the machine, green indicator light will light up;
2. Press the RED switch to turn on the power of the remote (Red Indicator Light is on) and press the RED switch again to turn off the power (Red Indicator Light is off);
3. Turn the rotary knob to active the machine and adjust output volume.

Note:

• You must turn on the power of the remote in order to use it.
• If you encounter any problem, please contact your local Antari dealer for assistant.

W-1 Wireless Transmitter (Standard for SW-250)

W-1 Wireless Remote is a standard accessory for SW-250 Wireless Snow Machine. If you already purchased the wireless model, it’s ready to use.

W-1 Wireless Transmitter

• Battery：27A 12V
• Effective Range：The effective range is approximately 50m, depends on actual condition, it may vary.
• W-1 wireless transmitter has 2 buttons, each function as follow:

W-1 Wireless Transmitter

Pairing

Each receiver can pair up to 5 transmitters, please follow the steps below to pair;

Step 1. Turn on the power, “Wireless Setup” will show on the display for 15 seconds. Within this time period, press button A on the W-1 transmitter to pair with the machine. When screen shows “Wireless Setup OK”, means it’s paired;
Step 2. Please repeat Step 1 to pair multiple transmitters;
*If exceed 15 seconds, turn the power off and on again.

WTR-10 Wireless Remote (Optional for SW-250X Only)

WTR-10 Wireless Remote set is an optional accessory for SW-250X Snow Machine, it included a W-1 transmitter and a W-1 receiver. If you purchase the WTR-10 Wireless Remote set afterwards, please follow the instruction below. If you encounter any problem, please contact your local Antari dealer for assistant.

W-1 Wireless Transmitter & Receiver

• Battery：27A 12V
• Effective Range：The effective range is approximately 50m, depends on actual condition, it may vary.
• W-1 wireless transmitter has 2 buttons, each function as follow:

W-1 Wireless Transmitter

W-1 Wireless Receiver

W-1 Wireless Receiver Installation

If you purchased the WTR-10 Wireless Remote set afterwards, please follow the instructions below to install the receiver. If you encounter any problem, please contact your local Antari dealer for assistant.

1. Please see graph 1, remove the cover from the pointed place;
2. You will see a white cable like graph 2, pull it out and connect to the W-1 receiver;
3. Screw it back to the machine like graph 3 and follow the instruction on 12.3 for pairing.

Pairing

Each receiver can pair up to 5 transmitters, please follow the steps below to pair;

Step 1. Turn on the power, “Wireless Setup” will show on the display for 15 seconds. Within this time period, press button A on the W-1 transmitter to pair with the machine. When screen shows “Wireless Setup OK”, means it’s paired;
Step 2. Please repeat Step 1 to pair multiple transmitters;
*If exceed 15 seconds, turn the power off and on again.

Service and Maintenance

DANGER
Disconnect the power cord before starting maintenance operation!

• Always keep the machine clean.
• Can use an air compressor, a vacuum or a soft brush to remove the dust on the machine.
• Can use a slightly damp cloth to clean the casing.
• Before store or after each use of the machine, pump pure water through the system for at least 1-2 minutes, this will help clean the snow fluid residue and extend the lifespan on the pump and the machine.
• Before store or after each use, please make sure the fluid tank is clean and dry.
• It is recommended to run the machine at least once a month in order to maintain its best performance and output condition.
• Excessive dust and build up liquid residue will reduce the performance and cause overheat.

Technical Specifications

EU Model: AC 220-240V, 50/60Hz 4.0A

Rated Power| 120V 900W

240V 880W

Fluid Consumption| 140 ml/min (100% output)
Fluid Tank Capacity| 5 Liters (1.32 Gallon)
Compatible Fluid| Antari SL Snow & Foam Fluid、Antari SL-A Premium Snow Fluid、Antari SL- N Snow & Foam Fluid (New Formula)、Antari SL-AN Premium Snow Fluid (New Formula)、Antari SL-H Super Dry Snow Fluid、Antari SL-C Anti-Freezing Snow

Fluid、Antari SL-UV UV Snow Fluid

Ambient Temp. Range| 5°C – 40°C (41°F – 104°F)
Control Methods| Manual、Timer、DMX512、Wireless

(Standard)、Cable Remote (Optional)

| Manual、Timer、DMX512、Wireless

(Optional)、Cable Remote (Optional)

Interface| XLR 5-Pin (DMX)、XLR 4-Pin (Remote)、IEC (Power)
DMX Channels| 1 Channel
Included Accessories| W-1 Transmitter、Hanging Bracket| Hanging Bracket
Optional Accessories| SC-2 Cable Remote、SW-300-FB Floor Bracket| WTR-10 Wireless Remote、SC-2 Cable

Remote、SW-300-FB Floor Bracket

Dimension| L 539 W 276 H 310 mm (L 21.22 W 10.87 H 12.20 inch)
Weight| 11.5 kg (25.35 lbs.)

Warranty Disclaimer

We guarantee the merchandise manufactured by us to be free from defect in material and workmanship for a period of one year. Our obligation and liability under this warranty shall be restricted to repair or replacement at our factory or local authorized dealer. We assume no liability of the products that are improperly used or used for any purpose other than that for which they are specially designed. This warranty shall not apply to any merchandise which has been repaired, altered or assembled outside our factory in any way so as in our judgment to affect its performance, nor which has been subjected to misuse, negligence, or accident nor to any merchandise operated contrary to our printed instructions. We will not allow or be liable of any loss or any damages of any kind in connection with the use, sale, or repair of any merchandise purchased from us.

Machine Dimension

Appendix I – Grounding Instruction

This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor. If repair or replacement of the cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120V circuit, and has a grounding plug that looks like the plug illustrated in sketch A in Figure. A temporary adaptor, which looks like the adaptor illustrated in sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet can be installed by a qualified electrician.
The green colored rigid ear, lug, and the like, extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by the metal screw.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>