YOUKAIN HDLP-026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan User Manual

June 12, 2024
YOUKAIN

HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan
User ManualYOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart
Ceiling Fan  -

Packing List:

YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan -
Packing List

Specification

Material Metal + ABS
Color White/Black
Weight 8.3KG
Motor Power 35W
Number Of Blades 3
Light Source Power 18W
Size 525218.5in/525223.4 in
Color Temperature 3000k-4500k-6500k
Luminous flux 1500lm

Installation

Note: Before installing the ceiling fan, make sure that the power has been turned off.

  1. Tools ready
    Philips screwdriver/Blade screwdriver/Adjustable pliers or wrench Step ladder/Wire cutter/Electical tape/Lmpact drillYOUKAIN HDLP 026AW Integrated
LED Indoor 3 Blades Smart Ceiling Fan - Tools

  2. Installation of bracket
    (1) To use wood screws to fix bracket for wooden or false ceiling.YOUKAIN
HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan - fix
bracket(2) To use expansion screws to fin bracket for concrete ceiling before that will need to drill dia.8mmexpansion bolts.YOUKAIN HDLP 026AW Integrated LED Indoor 3
Blades Smart Ceiling Fan - expansion screws

  3. Install the blades
    (1) Install the boom safety pin to the junction of the boom and the hanger.(Figure 1)YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart
Ceiling Fan - safety pin(2) Install the fan blades to the motor in order and screw on the fan blade screws in turn.(Figure 2)YOUKAIN HDLP 026AW Integrated LED Indoor 3
Blades Smart Ceiling Fan - fan blades

  4. Lamp installation
    YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan - Lamp
installation

  1. Connect the corresponding wires at the bottom of the lamp and the motor.
  2. Tighten the three screws on the edge of the switch cover
  3. Take out the decorative nuts, nuts, iron washers and plastic washers pre- locked on the lamp tube
    4)Install glass, tighten plastic washer, iron washer and nut in turn
  4. Install the decorative frame and fasten the decorative nutYOUKAIN HDLP
026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan - decorative
nut
  1. Installation of downrod, canopy and decorative cover Selection of downrod
  1. To select the correct downrod, either 5 inch or 10 inch according to the ceiling height. Put the canopy and decorative cover through the downrod;
  2. Remove the locking pin and the long pin. then remove the two downrod set screws;
  3. Fix the downrod set into the fan body, lock the downrod to the fan body with set screws.
  4. Mount the bracket onto outlet box by the screws, spring washers and flat washers.
  5. Hang the ball joint and the fan onto the bracket, make sure the guide pin of the bracket is fitted into slot of ball joint.
  6. Insert the remote control receiver between the bracket and the downrod.
  7. Connect wires from supply and the bracket to the wiring terminals.
  8. Attached canopy to the bracket by aligning canopy holes with the bracket holes .Fix the canopy to bracket with set screws.
  9. Install the blade brackets and blades with screws.YOUKAIN HDLP 026AW
Integrated LED Indoor 3 Blades Smart Ceiling Fan -
downrod
  1. Installation height
    Fan blades to the ground shall note less than 2.3 metersYOUKAIN HDLP 026AW
Integrated LED Indoor 3 Blades Smart Ceiling Fan - Installation
height

  2. Hanging ceiling fan

  1. Place the lobes in the hanger and turn the pipe so that the groove on the lobes engages the lugs on the dome(inside the hanger)
    The lug grouve must engage the hanger lug.YOUKAIN HDLP 026AW Integrated LED
Indoor 3 Blades Smart Ceiling Fan - ceiling fan
  1. Connect the power cord
    Connect the remote control driver as shown in the picture (the driver is finally placed in the mounting bracket).YOUKAIN HDLP 026AW Integrated LED
Indoor 3 Blades Smart Ceiling Fan - power cord

  2. The balance adjustment of the fan
    Fan is installed, if it shakes up and down, please check the screws in blades, downrod, and the lamp kit if they are fix, if not, please fix it with screw driver. lf it still shakes, please use the balancing kit stools and check the instruction of balancing kit inside the carton.

Instruction of the remote control

YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan - remote
control

  1. Turn off all loads.
  2. Fan speed control.
  3. LED indicator light.
  4. Turn on the light/Color Temperature Adjustment.
  5. Fan off.
  6. Fan positive and negative rotation control.
  7. Fan timing control.
  8. The remote control USES a pair of 1.5v batteries.
  9. Natural Wind.

Tips:

  1. The remote control and receiver are paired as learning codes. The remote control is turned to receive the controller within one minute after the receiver is powered on; Long press the natura wind buttonAbout 5 seconds, in the sound of a drop, that learningsuccess, can be used normally:(note: no learning is accepted if the power is energized for more than one minute)
  2. When the remote control cannot control the controller, please check whether the battery is loadet correctly;
  3. Too low battery voltage will affect the remote control distance and may cause remote control failure Please replace the battery in time
  4. When not in use for a long time, please remove the battery of the remote control;
  5. support the maximum 300VV lighting6. During installation, the ceiling cover of the fan shall not compress all the wires, which may easily cause the wires to break and short circuit

Function Description

YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan -
Function Description| YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart
Ceiling Fan - Function Description 1
---|---
YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart Ceiling Fan -
Function Description 2| YOUKAIN HDLP 026AW Integrated LED Indoor 3 Blades Smart
Ceiling Fan - Function Description 3

Frequently asked questions (FAQ)

Q: The fan/light/remote do not work?

Q: When the fan is on it makes a loud noise. Any ideas why?

A: 1. The noise might be caused by magnet debris generated during transportation, which could be attracted by the attached magnetic parts after the fan working for about 10 minutes. Therefore, in order to eliminate the noise, please try running the fan for about 10 minutes and see if the loud sound disappears. 2. There might be some screws left in the shell in the installation. Therefore, try to remove the lampshade, light source and chassis, turn the fan by hand, shake out the screws, and the sound can disappear. If you try the above tips and the fan still makes a loud noise, we will replace it for you immediately. Sorry for the inconvenience.

Q: I installed this fan, and there is a 1 or 2 second remote delay. Why?

A: Because there is a motor protection program. When the power is supplied, the receiver tests whether the motor matches it, and then works to start the fan. This is to protect the motor and make it more durable.

Q: Screw holes in mounting bracket do not match electrical box. Any advice?

A: The hole position is the computer digital punching, not the manual punching, so it is accurate in principle. However, there is an important tip in installation: You should fix all the screws into holes SLIGHTLY one by one, and then screws all the holes tightly. Otherwise the screws might not match with the holes accurately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

YOUKAIN User Manuals

Related Manuals