Gude GBTS 350 Concrete Cutter Instruction Manual

Translation of the original instructions
Concrete cutter

GBTS 350
55559
GÜDE GmbH & Co. KG
Birkichstrasse 6
74549 Wolpertshausen
Deutschland

GBTS 350 Concrete Cutter

Please read the instructions carefully before starting the machine.

Scope of delivery

|
---|---
|
|   
|
|
|   
|
|
|

Technical Data

Tare weight of the machine without cutting disc and accessories and with empty tank| 11,5 kg
Tank capacity| 0,55 I
max. Diameter| 350 mm
Inside-Diameter| 75.4 mm
Hole diameter| 25,4 mm
Outer flange: min. outside-Diameter d,| 98 mm
Tightening torque Cutting disc| 26 Nm
Width across flats working spindle| 15 mm
Max. speed of the cutting tool| 4400 mind
Diameter-working spindle| M 10
max. Spindle speed| 9500 1/min”
required water pressure required water nuantitv| 0,15 – 0,35 mPa
9- 17 Umin
Noise details
Measured according to DIN EN ISO 19432-1:2020 Attachment B; Uncertainty K = 3 dB (A)
Sound pressure level Lra Full load 9500min.’| 92,5 dB(A)
Guaranteed sound power level LWA Full load 9500 min.’| 116 dB(A)
Wear ear protectors.!|
Vibration details|
Vibration total values (triaxial vector sum) determined according to DIN FN ISO 19437-1:2020 Attachment C. Uncertainty K = 1 5 m/s’|
Full load 4800 min.’ Vibration emission value ahiod 1 9,822 m/s2

Read and understand the operating instructions before using the appliance.
Familiarise with the control elements and how to use the appliance properly.Observe all the safety measures listed in the instructions. Behave responsibly towards other people.
The operator is responsible for accidents or risks to third parties.
Specified Conditions of Use
The concrete cutter is suitable for working on kerbs, deep kerbs, concrete surfaces, paving stones and bone stones.
The unit can operate in wet or dry cutting mode.
Do not use this product in any other way as stated for normal use. Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.
Residual Risk
Even when the device is used properly and all safety regulations are complied with, there still may be some residual risks.
Despite the observance of the operating instructions there still may be some hidden residual risks.

Symbols

| Warning / Attention!
---|---
| Switch off the motor and wait for the cutting disc to come to a standstill
| To reduce the risk of injury, user must read instruction manual
| Weare a protective helmet.
| Wear gloves!
| Wear hearing protection
| Wear safety goggles
| Wear a suitable dust protection mask.
| Wear protective clothing
| Safety shoes to be used
| Kickback can lead to casualties.
| Exhaust fumes, fuel and lubricants are toxic substances. Breathing in exhaust fumes may
be fatal!
| Fuel mixture 40:1
| Hazardous dust and gas emission
| Fire hazard due to glowing material particles
| Keep a distance from the ejection opening at all times.
| Keep distance of persons Observe to keep out of dangerous zone
| Warning against risk of tripping
| Warning against hot surfaces!
| Sound power level
| Manually controlled lever winch
| The use of damaged cutting discs is not permitted.
| The use of a saw blade is prohibited.
| Prohibited smoking and open fire using.
| Open flames are prohibited
| Keep dry at all times. Never expose tool to rain.
| To be used outdoors only.
| Keep the machine out of reach of children.
| Protect against cold
| max. Spindle speed
| CE marking
| Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres.

General Safety Rules

Read all safety warnings and all instructions.  Save all warnings and instructions for future reference. Do not use the appliance if you are tired, ill, under influence of drugs, alcohol drinks or medicaments. Use protective equipment which fit you. Wear safety goggles and ear protection at all times. The operating personnel must have received sufficient training in use, setup and maintenance. Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education. Keep children and other persons including animals in a safe distance when using the appliance. It is necessary to comply with the regulations applicable in the country where the truck is used.
Cutting discs
Only use undamaged cutting discs that comply with the technical data stated in this manual and that meet national or regional standards/regulations, such as for example.

• EN 13236
• EN 12413
• ANSI B7.1

The use of other cutting accessories that deviate from the technical data, such as circular saw blades, is prohibited. Cutting discs must be checked for cracks, deformation and imbalance before use. Cutting discs may only be fixed with the flanges supplied with the machine. The use of other parts for fastening such as reducing bushes and spindle bushes is prohibited. Use only original accessories and original spare parts. Components for which there are no instructions for exchanging should be replaced by the manufacturer only. Using other spare parts can result in accidents/injuries of the user. The manufacturer will not be liable for any such damage. Please contact our service department if you need accessories or spare parts.
WARNING AGAINST CUTTING INJURIES
Guide the machine with a firm grip on both handles.
Position the machine as described in this manual.
Never leave the machine running unattended.
Do not carry the machine when it is running and the cutting disc is rotating.
No turning or tilting or moving during operation.
Never set the machine down on the ground while the cutting disc is rotating.
Whenever you stop work, switch off the engine and always wait until the cutting disc has come to a complete standstill.
Ensure the working space has sufficient general or targeted lighting.
WARNING
Risk of fire, Risk of explosion
Do not work with the unit in an environment with a risk of explosion where there are flammable liquids, gases or dust. Ensure adequate workplace ventilation.
WARNING
Exhaust gases, fuel and lubricants are toxic.
During operation, exhaust gases are produced that contain hydrocarbons and benzenes and are therefore harmful to health. Ensure adequate workplace ventilation.Bear this in mind not only when operating indoors, but also when working in trenches, troughs or other confined spaces.
If nausea, headaches, visual disturbances (e.g. reduced field of vision), hearing disturbances, dizziness or loss of concentration occur, stop working with the machine immediately. These symptoms can be caused, among other things, by excessive exhaust gas concentrations.
WARNING
Damage to hearing due to exposure to noise Wear hearing protection and limit exposure.
Increased attention and caution is required when wearing hearing protection. – The perception of sounds announcing danger (screams, signal tones, etc.) is limited.
Take timely breaks from work
WARNING – Vibration It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness, and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration: Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. After each period of operation, exercise to increase blood circulation. Take frequent work breaks. Limit the amount of exposure per day. If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor.

DANGER – Reaction forces
Reaction forces occur suddenly and can cause fatal injuries due to loss of control.
The following reaction forces usually occur:

• Kickback: In the event of kickback, the machine is thrown back to the user. Kickback occurs when the cutting disc flutters due to damage, imbalance or tilting and then gets jammed in the cutting gap or is slowed down sharply
• Drawing in: The machine pulls away from the user when the cutting disc touches the workpiece from above.
• Falling in the direction of separation: At the end of the cut, the machine loses the support provided by the cutting disc in the breakthrough kerf Now the user has to balance the weight of the machine. Bring your body and arms into a position allowing you to absorb the recoil forces. Never change the cutting direction and the angle to the workpiece after the machine has been set up. Secure the workpiece sufficiently against shifting.
  Position the machine so that the cutting disc cannot tilt.Follow all instructions in this manual

WARNING – High dust formation
Eye injuries and respiratory diseases caused by flying material particles.
Wear goggles.
Adjust the guard plate for the cutting disc so that the material particles are deflected away from the user and the machine.
Note the direction of flight of the separated material particles.
Observe to keep out of dangerous zone
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Do not machine any materials that present a danger to health (e.g. asbestos).
DANGER Fuel is highly flammable.
The appliance may only be refuelled outdoors and not near open fire or burning cigarettes. Prohibited smoking and open fire using. Emergency procedure After use, let the unit cool down for at least 5 minutes before refuelling. Dust can accumulate on the housing, which can become saturated with accidentally spilled or leaked petrol, creating a burn hazard. Therefore, clean the machine of dust regularly and especially before refuelling. In the tank pressure may develop. Loosen the tank cap slowly to allow this pressure to gradually decrease. Make sure the fuel does not overflow. If the fuel overflows, the engine must not be started. Remove any dirt from the appliance and prevent any attempt at ignition until fuel fumes have evaporated. Do not let fuel get on your clothes. Otherwise, change the clothes before starting the machine. Replace all fuel tank and container caps securely. Do not store any fuel near the unit. Keep the fuel in suitable containers only. Fuel tank to be emptied outdoors only. Never keep the unit with petrol in the tank inside a building where petrol vapours could get in contact with open fire or sparks.

Working Instructions

Organise the work to be carried out in advance and explore the site to exclude hazards due to the following causes electrical lines
Flammable materials
Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment.
Determine if warning signs need to be erected.

Maintenance

• For all work on the cutting machine
• Wear protective gloves.
• Switch off engine

General notes
Repairs and works specified in these instructions may only be performed by qualified authorised staff.
Use only original accessories and original spare parts.
Components for which there are no instructions for exchanging should be replaced by the manufacturer only.
Keep the device, in particular the air vents, clean at all times.
Never spray water on the device body!
Never clean the machine and its components with solvents, flammable or toxic liquids. Us only a damp cloth making.
Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries. If necessary, a list of spare parts can be found at www.guede.com.

Storage

For breaks in operation from approx. 3 months onwards
Empty and clean the fuel tank in a well-ventilated place.
Drain the carburettor, otherwise the diaphragms in the carburettor may stick. Store the machine in a cool, dry, and well-ventilated place that is inaccessible to children.

Disposal

Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres.
Transport packaging disposal
The packaging protects the machine against damage during transport. Packaging materials are usually chosen based on environment aspects and waste treatment principles and are therefore recyclable. Returning the packaging into material circulation saves raw materials and reduces waste production. Parts of packagings (e.g. foils, styropor®) can be dangerous for children.
Danger of asphyxiation!
Keep parts of the packagings out of reach of children and dispose them as soon as possible.
Guarantee
Warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device. The guarantee solely covers inadequacies caused by material defect or manufacturing defect. Original payment voucher with the sales date needs to be submitted for any claim in the guarantee period. The guarantee does not cover any unauthorised use such as appliance overloading, use of violence, damage as a result of any unauthorised interference or caused by foreign items. Failing to follow the operating and assembly instructions and common wear are also not included in the guarantee.
Important information for the customer
Please note that returns within or outside the warranty period should always be in the original packaging. This measure effectively avoids unnecessary transport damage and any associated disputed ruling. Your equipment is optimally protected only in the original box, and keeping it in that box will ensure smooth processing.

Service

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? We will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label. To always have these data at hand, please enter them below.
Serial No.:
Art. No:
Year of production:
Tel.: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com

Translation of the EC-Declaration of Conformity
We, hereby declare the conception and construction of the below mentioned appliances correspond – at the type of construction being launched – to appropriate basic safety and hygienic requirements of EC Directives.
In case of any change to the appliance not discussed with us the Declaration expires.
Concrete cutte
55559 GBTS 350
Appropriate EU Directives
2014/35 EU
1935/2004/EC
2011/65/EU&(EU)2015/863
2016/425/EU (PPE)
2015/1188/EU
2006/42 EC
2014/30/EU
1907/2006/EC
2016/426/EU
2019/1784/EU
2014/29/EU
Annex IV
Name:
No:
Notified Body
Adress:
Type Ex. Cert.-No.:
2016/1628/EU_2018/989/EU
Emission No.:
e92016/16282021/1068SHB1/P3104700
2000/14/EC_2005/88/EC
Method of compliance assessment
Annex VI
Wolpertshausen,
28.01.2022
Managing Director |
Harmonised standards used
EN ISO 19432-1:2020
AfPS GS 2019:01 PAK
EK9-BE-98:2020
EN ISO 14982:2009
Guaranteed sound power level
Measured sound power leve
Authorized to compile the technical fil

GÜDE GmbH & Co. KG
Birkichstrasse 6
74549 Wolpertshausen
Deutschland
Tel.: +49-(0)7904/700-0
Fax.: +49-(0)7904/700-250
eMail: info@guede.com
TN 55559 2022-05-15

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>