Holiday Living LW20-ST14 7 FT LED Pre-Lit Lamp Post With Greenery Instruction Manual
- June 8, 2024
- Holiday LIVING
Table of Contents
Holiday Living LW20-ST14 7 FT LED Pre-Lit Lamp Post With Greenery
ITEM/ARTICLE #0899440, 50175116
HOLIDAY LIVING and logo design are trademarks or registered trademarks of LF,
LLC. All rights reserved.
Thank you for purchasing this Holiday Living product. We’ve created these
easy-to-follow instructions to ensure you spend your time enjoying the product
instead of putting it together. But, if you need more information than what is
provided here, please visit Lowes.com, search the item number and refer to the
Guides & Documents tab on the product’s page.
If the item is no longer for sale, or if you have any questions or problems,
please call our customer service department at
888-251-1006, 8 a.m. – 8 p.m., EST,
Monday – Sunday. You could also contact us at
partsplus@lowes.com.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION
- Product is intended for indoor and covered outdoor use. To reduce the risk of fire, do not deliberately reposition either bulb or lampholder contact.
- To reduce the risk of overheating, replace burned out lamps promptly. This is an electrical product not a toy! To avoid the risk of fire, burns, personal injury, and electric shock it should not be played with or placed where small children can reach it.
- Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
- This seasonal use product is not intended for permanent installation or use
- Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
- Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
- Do not let lamps rest on the supply cord or on any wire
- Unplug the product when leaving the house, when retiring for the night, or if left unattended
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from cord, wire, or light string.
- Do not close doors or windows on the product or extension cord as this may damage the wire insulation.
- Do not cover the product with a cloth, paper or any material not part of the product when in use.
TROUBLESHOOTING
| PROBLEM PROBLÈME | CORRECTIVE ACTION | |
|---|---|---|
| CAUSE POSSIBLE | MESURE CORRECTIVE |
Lights do not work.
| 1. Loose connect between adapter and light set.| 1. Reconnect the plug.
2. Replace the bulb.
| 2. Bulb burned out.
CARE AND MAINTENANCE
-
Before using or reusing, inspect product carefully. Discard any products that have cut, damaged or frayed wire insulation or cord, cracks in the lamp holders
or enclosures, loose connections, or exposed copper wire. -
When not in use, store neatly in a cool, dry location protected from sunlight.
SAFETY INFORMATION
BULB REPLACEMENT INSTRUCTIONS
- Pull up the lamp lock, grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
- Pull lamp and plastic base straight out of lamp holder.
- Replace lamp and press down the lamp lock with only 3 Volt push-in type lamp provided with product
PREPARATION
- Before beginning installation of product, make sure all parts are present. Compare parts with package contents list.
- If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated Assembly Time: 5 minutes.
PACKAGE CONTENTS
INSTALLATION OVERVIEW
- Insert the short metal pole (B) into the base (A).
- Insert the lamp post body (C) into the short metal pole (B). Note: There are metal frame and long metal pole on the lamp post body (C). Make sure you insert the metal frame before you insert the long metal pole.
- Insert the lamp post head (D) into the lamp post body (C), connect the plug of the light set of the lamp post head (D) into the end plug from the lamp post body (C) and screw the cap.
- Plug the adaptor (F) into the power supply. The product should be lit now.