VISUAL COMFORT S 2189 Halle Petite Wall Lantern Instruction Manual

VISUAL COMFORT S 2189 Halle Petite Wall Lantern

Product Information:

• Product Name: Halle Petite Wall Lantern
• Item Number: S 2189
• Bulb: Not included

Assembly Instructions

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove the mounting plate (B) from the fixture body (G) by removing the side screws (F).
3. Remove the lantern (I) from the fixture body (G) by removing the side screws (H).
4. Using the mounting plate (B) as a guide, line it up with the junction box and mark the anchor positions.
5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into the holes using a hammer.
6. Install the mounting plate (B) to the junction box and secure it with mounting screws (D), then secure wood screws (C) to anchors (A).
7. Wrap the fixture ground wire (green) around the green grounding screw.
8. Install the fixture body (G) to the mounting plate (B) and secure it with side screws (F).
9. Install the light bulb into the socket.
10. Install the lantern (I) to the fixture body (G) and secure it with side screws (H).
11. If installing in wet locations, ensure that the drain hole is positioned at the bottom of the fixture frame. Refer to diagram 2.
12. For outdoor/wet location installation, apply a small bead of silicon compound where the backplate meets the wall to prevent water from entering. Note that large gaps will need to be corrected before applying the silicon compound.

Care Instructions

Clean the product only with a soft dry cloth or feather duster.
Do not use abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS

Halle Petite Wall Lantern
Item # S 2189

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Hammer
• Slotted Screwdriver
• Pencil
• Drill

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (B) from fixture body (G) by removing side screws (F).

3. Remove lantern (I) from fixture body (G) by removing side screws (H).

4. Using mounting plate (B) as a guide, line up with the junction box and mark anchor positions.

5. Using a drill bit slightly smaller than the anchor, drill holes in the marked positions. Install anchors (A) into holes using the hammer.

6. Install mounting plate (B) to junction box and secure with mounting screws (D), then secure wood screws (C) to anchors (A).

7. Wrap fixture ground wire (green) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (E).
   NOTE: It is imperative that the fixture is grounded.

8. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (E).

9. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (E).
   CAUTION: Do not reverse the hot and neutral connections.

10. Make sure all wire connections are tight, then carefully tuck into the junction box.

11. Install fixture body (G) to mounting plate (B) and secure with side screws (F).

12. Install light bulb into the socket.

13. Install lantern (I) to fixture body (G) and secure with side screws (H).
    NOTE: For wet location installation drain hole must be positioned at bottom of fixture frame. See diagram 2.
    FOR OUTDOOR/WET LOCATION INSTALLATION:

14. Using silicon compound, apply a small bead where backplate meets the wall to prevent water from entering.
    NOTE: Large gaps will need to be corrected before applying silicon compound.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

FEATURED

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>