VISUAL COMFORT PCD 5205 Large Ring Chandelier Instruction Manual

: June 12, 2024
: VISUAL COMFORT

Table of Contents

VISUAL COMFORT PCD 5205 Large Ring Chandelier
Product Information
Product Usage Instructions
TOOLS REQUIRED (NOT INCLUDED)
ASSEMBLY INSTRUCTIONS
Care Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VISUAL COMFORT PCD 5205 Large Ring Chandelier

Product Information

Product Name: Orsay Large Ring Chandelier

Item Number: PCD 5205

Contents: Chandelier, Mounting Plate (A) , Canopy (D), Collar Ring (E), Bottom Rod (H) , Wire Nut (B) , Light Bulbs, Diffusers (J)

Notice: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.

Product Usage Instructions

Carefully remove all parts from the box. Place on a clean, soft surface.
Remove mounting plate (A) from canopy (D) by removing collar ring (E).
Install mounting plate (A) to the junction box and secure it with mounting screws (C).
Feed electrical and ground wires through the bottom rod (H) and connect.
Connect the fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (B).
Connect the fixture hot wire (black) to the supply hot wire (usually black) using wire nut (B). CAUTION: Do not reverse the hot and neutral connections.
Make sure all wire connections are tight, then carefully tuck them into the junction box.
Install canopy (D) to mounting plate (A) and secure with collar ring (E).
Install the light bulb into the socket by lining up the base to holes and twisting it to secure it.
Thread diffusers (J) on socket bases.

Care Instructions

Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Orsay Large Ring Chandelier

Item # PCD 5205

NOTICE

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

Phillips Screwdriver
Slotted Screwdriver
Wire Cutters
Wire Strippers

ASSEMBLY INSTRUCTIONS

Carefully remove all parts from the box. Place on a clean, soft surface.
Remove mounting plate (A) from canopy (D) by removing collar ring (E).
Install mounting plate (A) to the junction box and secure it with mounting screws (C).
Feed electrical and ground wires through the bottom rod (H) and connect to the fixture body (I). Repeat for the middle rod (G) , connecting to the bottom rod (H).
Continue feeding wires through collar ring (E) and canopy (D).
Holding fixture upright, slide collar ring (E) and canopy (D) down, and rest on fixture body (I). Then connect the top rod (F) to the middle rod (G).
NOTE: Slide components down slowly to avoid damage.
Hang fixture swivel ball (K) to the center of mounting plate (A).
Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8”.
Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (B).
NOTE: It is imperative that the fixture is grounded.
Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (B).
Connect the fixture hot wire (black) to the supply hot wire (usually black) using wire nut (B).
CAUTION: Do not reverse the hot and neutral connections.
Make sure all wire connections are tight, then carefully tuck them into the junction box.
Install canopy (D) to mounting plate (A) and secure with collar ring (E).
Install a light bulb into the socket by lining up the base to holes and twisting it to secure it.
Thread diffusers (J) on socket bases.

NOTICE

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.