steinel L 800 Outdoor Lights and Outdoor Lights with Motion Detector Instruction Manual

: June 12, 2024
: STEINEL

Table of Contents

steinel L 800 Outdoor Lights and Outdoor Lights with Motion Detector
About this document
General safety precautions
Principle
Electrical connection
Functions
Manual override function
Maintenance/care
Declaration of Conformity
Manufacturer’s Warranty
Technical specifications
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

steinel L 800 Outdoor Lights and Outdoor Lights with Motion Detector

About this document

Please read carefully and keep in a safe place.

Under copyright. Reproduction either in whole or in part only with our consent.
Subject to change in the interest of technical progress.

Symbols

Hazard warning!
Reference to other information in the document.

General safety precautions

Disconnect the power supply before attempting any work on the unit.

During installation, the electric power cable being connected must not be live. Therefore, switch off the power first and use a voltage tester to make sure the wiring is off-circuit.
Installing the sensor-switched light involves work on the mains voltage supply. This work must therefore be carried out professionally in accordance with national wiring regulations and electrical operating conditions. ( e.g. DE: VDE 0100, AT: ÖVE / ÖNORM E8001-1, CH: SEV 1000 )

L 800 S / L 810 S / L 820 S / L 800 C / L 810 C / L 800 SC / L 810 SC / L 820 SC $steinel-L-800-Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector- FIG- $1$$ $steinel-L-800-Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $2$$ $steinel-L-800 -Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $3$$ $steinel-L-800 -Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $4$$ $steinel-L-800 -Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $6$$ $steinel-L-800 -Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $7$$

Light enclosure
Wall mount
Bottom cover
Top cover
Mains lead, concealed wiring
Mains lead, surface wiring
Mounting hook to simplify installation/cable strain relief grips
Spacers for surface wiring
House number panel (L 820 S / L 820 SC)
Retaining screws for house number panel (L 820 S / L 820 SC)
Reach setting (S only)
Time setting (S only)
Twilight setting (S only)
Program setting (S only)
Manual override function

Principle

Sensor-switched light with an active motion detector. The integrated iHF sensor emits high-frequency electromagnetic waves ( 5.8 GHz ) and receives their echo. Any movement by persons in the light’s detection zone is noticed by the sensor as a change in echo. A microprocessor then issues the switch command “switch light ON”. Detection is possible through doors, panes of glass or thin walls.
(L 800 C / L 800 SC / L 810 C / L 810 SC / L 820 SC)

Note:

When installing, please always allow a distance of at least 3 m to Wi-Fi routers or access points.
The functions of the sensor-switched light can be set via smartphone and tablet or control dial.
Bluetooth interconnection is only possible via smartphone or tablet. (L 800 SC / L 800 C / L 810 SC / L 810 C / L 820 SC)

Detection zones for wall mounting:

Minimum reach ( 1 m )
Maximum reach ( 5 m )

Note:
If lights are mounted too close together, switching errors may occur as the high-frequency signals emitted will interfere with each other (Fig. A).

The following measures will help to avoid switching errors of this kind:

Allow a distance of at least 5 m between lights.
Interconnect lights via the Smart Remote app and selectively deactivate the sensor in individual lights via the Sensor-Off function (Fig. B + C).
As a result of interconnection, movement will also switch lights ON in spite of their sensor being deactivated.

Note:
The high-frequency output of the iHF sensor is is approx. 1 mW – 1.000 times less than the transmission power of a mobile phone or microwave oven.
Note:
The sensor is suitable for switching light on automatically.
Note : weather conditions may affect the way the sensor works. Strong gusts of wind, snow, rain or hail may cause the light to come on when it is not wanted.

Electrical connection

To achieve the stated reach of 5 m, the light should be mounted at a height of approx. 2 m. Connecting the mains power supply lead ( see diagram )

The supply lead is a three-core cable:

L = phase conductor ( usually black, brown or grey )
N = neutral conductor ( usually blue )
PE = protective-earth conductor ( green/yellow )

If you are in any doubt, identify the conductors using a voltage tester; then disconnect from the power supply again. Phase ( L ) and neutral conductor ( N ) are connected to the terminal block.

Important:
Incorrectly wired connections will produce a short circuit later on in the product or your fuse box. In this case, you must identify the individual conductors once again and reconnect them.

Note:
The light source of this luminaire cannot be replaced. If the light source needs to be replaced( e.g. at the end of its service life ), the complete luminaire must be replaced.

A mains power switch for turning the unit ON and OFF may of course be installed in the mains supply lead.

Functions

The sensor-switched light can be put into service after mounting the enclosure and connecting to the mains power supply. When putting the light into operation manually at the light switch, it will switch OFF after 1 second for the calibration phase and is then activated for sensor mode.
It is not necessary to operate the light switch a second time.
Functions can be set via Smart Remote app
(L 800 SC / L 800 C / L 810 SC / L 810 C / L 820 SC) or control dial.
Note: The settings last selected on the control will be used.

Smart Remote app
To configure the light via smartphone or tablet, you must download the STEINEL Smart Remote app from your app store. You will need a Bluetoothcapable smartphone or tablet.

QR codes $steinel-L-800-Outdoor-Lights-and-Outdoor-Lights-with-Motion- Detector-FIG- $10$$

Additional functions only via the Smart Remote app:

Main light- / basic light level adjustable
Extended reach adjustment
Group interconnection
Twilight setting by teach-in

Reach setting (sensitivity ) (S only) factory setting: 5 m Reach is the term used to describe the semi-circular zone that is produced on the ground when mounting the light at a height of 2 m

Potentiometer set to “max” = max. reach of 5 m
Potentiometer set to “min” = min. reach of 1 m
Potentiometer “off” = Sensor OFF

Sensor off :
Motion detection and all other sensor functions are completely deactivated. We recommend selecting the shortest time ( 5 seconds ) for setting the detection zone.

Tine setting ( switch-off delay) (S only)

Factory setting: 5 s
The light’s ON time can be set to any period from approx. 5 s to a maximum of 15 min (for S) or from approx. 5 s to a maximum of. 60 min (for SC).

Any movement detected before this time elapses will restart the timer. The shortest time setting is recommended when adjusting the detection zone and performing the functional test.

Note:
After the light switches OFF, it takes approx. 1 second before it is able to start detecting movement again. The light will only switch ON in response to movement once this period has elapsed.

Twilight setting (response threshold) (S only)
Factory setting: 2,000 lux
The light’s chosen response threshold can be infinitely varied from approx. 2 to 2,000 lux.

To adjust the detection zone in daylight, the control dial must be set to 2000 lux

Programme setting (S only)

Manual override function

If a mains switch is installed in the mains supply lead, the following functions are available in addition to simply switching light ON and OFF:

$steinel-L-800-Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $5$$

Sensor mode 15.1 :

Switch light ON (when light is OFF):
Switch OFF and ON once. Light stays ON for the period selected.
Switch light OFF (when light is ON):
Switch OFF and ON once. Light goes out or switches to sensor mode.

Manual override 15.2 :

Activate manual override:
Switch OFF and ON twice. The light is set to stay ON for 4 hours ( blue LED lights up behind the diffuser d ). Then it returns automatically to sensor mode ( blue LED OFF ).
Deactivate manual override:
Switch OFF and ON once. Light goes out or switches to sensor operation.

Important:
The switch should be actuated in rapid succession ( in the 0.2–1-second range ).

What is soft light start?

The sensor-switched light features a soft light start function. This means that when turned ON, the light is not switched directly to maximum output but gradually builds up brightness to 100% within the space of a second. Brightness is also gradually reduced when the light is switched OFF.

What is basic light level?

The basic light level provides continuous nighttime illumination at approx. 10% light output. The light only switches to maximum output (100%) in response to movement in the detection zone (see Time setting l ). The light then returns to the basic light level (approx. 10%). The SC version switches the light to the basic light level you preselect (10- 50%).

Note:
Depending on the local power grid, the LED’s may flicker slightly when dimmed. This is not a product defect and no reason for complaint

Maintenance/care

The product requires no maintenance.
The light can be cleaned with a damp cloth ( without detergents ) if dirty.
Important note: the control gear cannot be replaced.

Disposal

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner.
Do not dispose of electrical and electronic equipment as domestic waste.

EU countries only:

Under the current European Directive on Waste Electrical and Electronic Equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Declaration of Conformity

Hereby, STEINEL Vertrieb GmbH declares that the radio equipment type L 800 SC / L 800 S / L 800 C / L 810 SC / L 810 S / L 810 C / L 820 SC / L 820 S is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: www.steinel.de

Manufacturer’s Warranty

This Steinel product has been manufactured with utmost care, tested for proper operation and safety and then subjected to random sample inspection.
Steinel guarantees that it is in perfect condition and proper working order. The warranty periodis 36 months and starts on the date of sale to the consumer. We will remedy defects caused by material flaws or manufacturing faults. The warranty willbe met by repair or replacement of defective parts at our own discretion. The warranty shall not cover damage to wear parts, damage or defects caused by improper treatment or maintenance.
Further consequential damage to other objects shall be excluded.
Claims under the warranty will only be accepted if the unit is sent fully assembled and well-packed with a brief description of the fault, a receipt or invoice ( date of purchase and dealer’s stamp ) to the appropriate Service Centre.

Repair service:
If defects occur outside the warranty period or are not covered by the warranty, ask your nearest service station for the possibility of repair.

WARRANTY

3 YEAR WARRANTY MANUFACTURER’S

Technical specifications

Dimensions ( H × W × D )| 88 × 230 × 145 mm (L 800 S / L 800 SC / L 800 C)

91 × 230 × 145 mm (L 810 S / L 810 SC / L 810 C)

260 × 230 × 145 mm (L 820 S / L 820 SC)

|
---|---|---
Material| Light enclosure: aluminium

Light diffuser: plastic

|
Power supply| 220 – 240 V, 50/60 Hz|
Power consumption ( Pon )| 7.50 W (L 800 S / L 800 SC / L 800 C)

9.80 W (L 810 S / L 810 SC / L 810 C)

9.80 W (L 820 S / L 820 SC)

|
Power consumption of iHF sensor| 0.61 W (SC / C only)|
Light output| 466 lm (L 800 S / L 800 SC / L 800 C)

679 lm (L 810 S / L 810 SC / L 810 C)

679 lm (L 820 S / L 820 SC)

|
Efficiency| 62 lm/W (L 800 S / L 800 SC/ L 800 C)

69 lm/W (L 810 S / L 810 SC / L 810 C)

69 lm/W (L 820 S / L 820 SC)

For C: only in combination with a Bluetooth sensor-switched product

|
Time setting| For SC: 5 s – 60 min For S: 5 s – 15 min

For C: only in combination with a Bluetooth sensor-switched product

|
Basic light level| For S: 0 %, 10 % (can only be set by adjustment control) For SC: 0 %, 10 – 50 % (with optional Smart Remote)

For C: 0 – 50 % soft start (with optional Smart Remote) and only in combination with a Bluetooth sensor-switched product

|
Permanent light| selectable ( 4 h )|
IP rating| IP 44|
Protection class| II|
Ambient temperature| -20°C to +40°C|
Bluetooth frequency| 2.4 – 2.48 GHz (L 800 / L 810 / L 820 SC)|
Bluetooth transmitter power| 5 dBm / 3 mW (L 800 / L 810 / L 820 SC)
---|---
Sensor frequency| 5.8 GHz
Sensor transmitter power| < 1 mW
Colour consistency SDCM| Starting value: 3

Luminous intensity distribution

$steinel-L-800-Outdoor-Lights-and-Outdoor-Lights-with-Motion-Detector-FIG- $16$$

(L 800 S / L 800 SC / L 800 C)| This product contains an energy efficiency class “E” light source
---|---
(L 810 S / L 810 SC / L 810 C) (L 820 S / L 820 SC)| This product contains an energy efficiency class “D” light source

Troubleshooting

Malfunction| Cause| Remedy|
---|---|---|---
Sensor-switched light without power| ■ Fuse has tripped, not switched ON, break in wiring

■ Short circuit

| ■ Activate, change fuse, turn ON mains switch, check wiring with voltage tester

■ Check connections

|
Sensor-switched light will not switch ON| ■ Twilight control set to night mode during daytime operation

■ Mains switch OFF

■ Fuse has tripped

■ Detection zone not correctly adjusted

| ■ Reset

■ Switch ON

■ Activate, change fuse, check connection if necessary

■ Readjust

|
Sensor-switched light will not switch OFF| ■ Continued movement within the detection zone| ■ Check detection zone and readjust if necessary|
Sensor-switched light will not switch OFF completely| ■ Basic lighting level selected| ■ Turn programme selector dial to 0|
Sensor-switched light switching ■ Wind is moving trees and ON when it should not bushes in the detection zone

■ Cars in the street are detected

| ■ Change detection zone

■ Change detection zone

Æ Region EU/Region US

|
Forgotten password?| ■ After entering wrong password: “Reset password” button; switch power supply OFF and back ON again within 10 minutes; then

re-enter password

■ Declare LED floodlight as master

|
No Bluetooth LED floodlight found| ■ LED floodlight is not in reach

■ Bluetooth is deactivated on smartphone

| ■ Check whether Bluetooth is activated on smartphone or reduce distance to the product

■ Re-start search

|
No connection being set up from ■ Smartphone too close to device smartphone to LED floodlight

■ Smartphone not compatible with app

■ App version not up to date

| ■ Distance to LED floodlight at least 1.5 m

■ Use different smartphone

■ Update Smart Remote app in app store

|

STEINEL Vertrieb GmbH
Dieselstraße 80-84 33442 Herzebrock-Clarholz
Tel : +49/5245/448-188
www.steinel.de
Subject to technical modification without notice.