sunmi P2 T6900 Handheld Mobile User Guide

sunmi P2 T6900 Handheld Mobile

Product Information

• NFC Reader: Used for sensing Quick Pass Card.

• Magnetic Card Reader: Used for reading the information stored in the magnetic stripe of a bank card.

• Front-facing Camera (optional): Supports photographing and 1D/2D code quick scanning.

• Type-C USB: Used for charging equipment and debugging by developers. Do not charge the battery in hazardous locations.

• Function Key: Used for customized functions.

• Power Button: Short press: wake up the screen, lock the screen. Long press: long press for 2-3 seconds in power off mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power off or reboot. Long press for 11 seconds when the system is frozen for automatic reboot.

• Printer: Used for printing sales slips in power on mode.

• Indicator Lamp: Used for indicating the steps for swiping card.

• IC Card Socket: Used for inserting the bank chip card.

• Two Dimensional Code Scanner (optional): Used to read commodity code and mobile payment code. Attention: do not look directly into the eyes.

• Rear Camera: Supports photographing and 1D/2D code quick scanning.

• Extend Pins: To connect to dock. (Need to buy dock separately) Do not use dock in hazardous locations.

• Slide Down the Metal Buckle and Take Out the Nano
  SIM: Used for inserting the Nano SIM card.

• SIM Card Slot (PSAM optional): Used for inserting the SIM Card (PSAM optional). Do not open and insert SIM card when an explosive atmosphere is present.

• PSAM Card Slot: Used for inserting the PSAM Card. Do not open and insert PSAM card when an explosive atmosphere is present.

• Micro SD Card Slot: Used for inserting extend SD card.

• Nano SIM Card Slot: Used for inserting Nano SIM card.

Product Usage Instructions

NFC Reader: To use the NFC reader, simply bring your Quick Pass Card close to the device.

Magnetic Card Reader: Swipe the bank card with the magnetic stripe through the card reader to read the stored information.

Front-facing Camera (optional): Use the camera for photographing or quick scanning of 1D/2D codes.

Type-C USB: Use the Type-C USB port for charging the device or debugging by developers. Avoid charging the battery in hazardous locations.

Function Key: The function key can be customized for specific functions.

Power Button: Short press the power button to wake up or lock the screen. Long press for 2-3 seconds in power off mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power off or reboot. Long press for 11  seconds when the system is frozen for automatic reboot.

Printer: The printer is used to print sales slips when the device is powered on.

Indicator Lamp: The indicator lamp indicates the steps for swiping a card.

IC Card Socket: Insert the bank chip card into the IC card socket.

Two Dimensional Code Scanner (optional): Use the scanner to read commodity codes and mobile payment codes. Avoid looking directly into the eyes.

Rear Camera: Use the rear camera for photographing or quick scanning of 1D/2D codes.

Extend Pins: Connect the device to a dock using the extend pins (dock needs to be purchased separately). Avoid using the dock in hazardous locations.

Slide Down the Metal Buckle and Take Out the Nano SIM: Slide down the metal buckle and remove the Nano SIM card from the slot.

SIM Card Slot (PSAM optional): Insert the SIM card (PSAM optional) into the SIM card slot. Do not open and insert the SIM card when an explosive atmosphere is present.

PSAM Card Slot: Insert the PSAM Card into the PSAM card slot. Do not open and insert the PSAM card when an explosive atmosphere is present.

Micro SD Card Slot: Insert an extend SD card into the Micro SD card slot.

Nano SIM Card Slot: Insert a Nano SIM card into the Nano SIM card slot.

Note: Please refer to the user manual for detailed safety instructions and regulatory compliance information.

Quick start

1. NFC reader
   Used for sensing Quick Pass Card.

2. Magnetic card reader
   Used for reading the information stored in the magnetic stripe of bank card.

3. Front-facing camera (optional)
   Supports photographing and 1D/2D code quick scanning.

4. Type-C USB
   Used for charging equipment and debugging by developers. Do not charge the battery in hazardous location.

5. Function Key
   Used for customized function.

6. Power button
   Short press: wake up the screen, lock the screen.
   Long press: long press for 2-3 seconds in power off mode to switch on the device.
   Long press for 2-3 seconds in normal operation mode to select power off or reboot.
   Long press for 11 seconds when system is frozen for automatic reboot.

7. Printer
   For printing sales slips in power on mode.

8. Indicator lamp
   Used for indicating the steps for swiping card.

9. IC Card socket
   Used for inserting the bank chip card.
   Two dimensional code scanner(optional)
   Used to read commodity code and mobile payment code. Attention: do not look directly into the eyes.

10. Rear camera
    Supports photographing and 1D/2D code quick scanning.

11. Extend pins
    To connect to dock.(Need to buy dock separately)
    Do not use dock in hazardous location.
    Slide down the metal buckle and take out the Nano SIM

12. SIM card slot (PSAM optional)
    Used for inserting the SIM Card(PSAM optional)
    Do not open and insert SIM card when an explosive atmosphere is present.

13. PSAM card slot
    Used for inserting the PSAM Card.
    Do not open and insert PSAM card when an explosive atmosphere is present

14. Micro SD card slot
    Used for inserting extend SD card.

15. Nano SIM card slot
    Used for inserting Nano SIM card.

Printing instructions

This device supports 58mm thermal paper with the specifications of 57±0.5mm*Ø40mm.

1. Please open the paper container with the uncovering handle ，Please do not force open the paper container to avoid print head gear wear;
2. Feed the paper correctly into the paper container in the  direction as shown, and pull some paper outside the cutter;
3. Close the cover of the paper container to finish printing paper feeding .
   Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction.
   Do not open paper container when an explosive atmosphere is present.

Notices
Safety Warning

• WARNING – DO NOT CHARGE THE BATTERY IN HAZARDOUS LOCATION, including cable and cradle.
• WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT, including inserting SIM card, changing paper roll.
• This device is anti-explosion product with Ex ic IIA T3 level. Please use it in the according environment.
• Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;
• This is a Class A product. This product may cause radio interference in living environments. In that case, the user may be required to take adequate measures against interference.
• Battery is un-removable. Please don’t change the battery by yourself.

Significant Safety Instructions
Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;
Please turn off the power immediately if you notice abnormal odor, heat or smoke;
The paper cutter is sharp, please do not touch!

Suggestions
Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;
Do not use the terminal in extremely cold or hot environments, such as near flames or lit cigarettes;
Do not drop, throw or bend the device;
Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;
Please do not use the terminal near medical equipment without permission.
The power source should meet limited power source or PS2 requirements according to IEC 62368-1 standard.

Statements
The Company does not assume responsibilities for the following actions:
Damages caused by use and maintenance without complying with the conditions specified in this guide;
The Company will not assume any responsibilities for the damages or problems caused by optional items or consumables (rather than the initial products or approved products of the Company). The customer is not entitled to change or modify the product without our consent. The product’s operating system supports official system updates, but if you change the operating system into a third party ROM system or alter the system files by system cracking, it may cause system
instability and security risks and threats.

Disclaimer
As a result of product upgrading, some details in this document may not match the product, and the actual product shall govern. The Company reserves the right of interpretation of this document. The Company also reserves the right toaster this specification without prior notice.
Modo di protezione： II 3G Ex ic IIB T4 Gc

RF Exposure Statement (SAR)
This device has been tested and meets EU, FCC and IC RSS-102 applicable limits for radio frequency (RF) exposure.
Please visit: www.sunmi.com.When properly worn on the body, the maximum SAR value of 1.254W/kg (1gSAR, test distance :5mmlimit 1.6W/kg) meets the RSS-102 readiness requirements.

EU regulatory conformance

Conformity CE
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://develop- er.sunmi.com/docs/read/en-US/maaeghjk480

INFORMATION ABOUT THE SOFTWARE
The description of accessories and components, including software,
which allow the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity at the following internet address:
https://developer.sunmi.com/docs/read/en-US/maaeghjk480.

RESTRICTIONS OF USE
5150-5350MHz only be used by indoor.

Technical specifications

CE certification information (SAR)
This device was tested for typical body-worn operations with the back of the handset kept 0mm away. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided.
If you are using pacemaker, hearing aid, cochlear implant or other device, please use the phone according to the doctor’s advice.

PRODUCT SAFETY WARNINGS

Use responsibly. Read all instructions and safety information before use to avoid injury. The limit operating ambient temperature of the equipment declared by the manufacturer is -15~55°C

Battery safety
Charge battery only at ambient temperatures ranging from 40°C.

1. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to battery manufacturer’s instructions.
2. CAUTION: Risk of explosion if battery is replaced by an incorrect type . Dispose of used batteries according to the instructions.
3. CAUTION: Battery charging temperature upper limit is 40°C.

Adapter safety

When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 0°C~40°C.
For altitude 2km below use only

Wi-Fi Safety
Turn Wi-Fi off in areas where Wi-Fi use is prohibited or when it may cause interference or danger, such as in airplanes while flying.

Technical features and characteristic

| Operation Frequency| Transmitted
---|---|---
GSM 900| 880.0–915.0MHz(TX), 925.0–960.0MHz(RX)| 33dBm
GSM 1800| 1710.0–1785.0MHz (TX), 1805.0–1880.0 MHz (RX)| 30dBm
WCDMA Band I| 1920-1980MHz (TX), 2110-2170MHz (RX)| 23dBm
WCDMA Band VIII| 880-915MHz (TX), 925-960MHz (RX)| 24dBm
LTE BAND 1| 1920-1980MHz (TX), 2110-2170MHz (RX)| 22.5dBm
LTE BAND 3| 1710-1785 MHz (TX), 1805-1880MHz (RX)| 22.5dBm
LTE BAND 7| 2500-2570MHz(TX), 2620-2690MHz(RX)| 22.5dBm
LTE BAND 8| 880-915MHz(TX) , 925-960MHz(RX)| 22.5dBm
LTE BAND 20| 832-862MHz(TX),791-821MHz(RX)| 22.5dBm
LTE BAND 38| 2570-2620MHz (TX/RX)| 22.5dBm
LTE BAND 40| 2300-2400MHz (TX/RX)| 22.5dBm
BT/BLE| 2402MHz-2480MHz| 6.5dBm
2.4G Wi-Fi| 2412MHz-2472MHz| 14dBm
5G Wi-Fi| 5.15-5.35GHz| 12dBm
5G Wi-Fi| 5.725-5.850GHz| 12dBm
NFC| 13.56 MHz

ISED Canada compliance statements

This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Manufacture
Shanghai Sunmi Technology Co., Ltd.
Room 505, No.388 ,Song Hu Road, Yang Pu District,
Shanghai, China

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Technical features and characteristic

| Operation Frequency| Transmitted
---|---|---
GSM 850| 824-849 MHz| 33.5 dBm
GSM 1900| 1850-1910 MHz| 31.5 dBm
WCDMA BAND II| 1850-1910 MHz| 24 dBm
WCDMA BAND IV| 1710-1755 MHz| 23 dBm
WCDMA BAND V| 824-849 MHz| 24 dBm
LTE BAND 2| 1850-1910 MHz| 23.5 dBm
LTE BAND 4| 1710-1755 MHz| 22.5 dBm
LTE BAND 5| 824-849 MHz| 23.5 dBm
LTE BAND 7| 2500-2570 MHz| 22.5 dBm
LTE BAND 17| 704-716 MHz| 23 .5dBm
LTE BAND 41| 2496-2690 MHz| 24dBm
WIFI| 2412-2462 MHz| 15.5 dBm
BT| 2402-2480 MHz| 7.5 dBm
BLE| 2402-2480 MHz| 7 dBm
5G WIFI| 5150MHz-5825MHz| 13 dBm
NFC| |

Declaration of Conformity

| AT| BE| BG| CY| CZ| DE| DK| EE| ES| FI| FR
---|---|---|---|---|---|---|---|---|---|---|---
GR| HU| IE| IT| LT| LU| LV| MT| NL| PL| PT
RO| SE| SI| SK| UK

(NI)

| | | | | |

EU Representative :SUNMI France SAS 186,avenue Thiers,69006 Lyon, France
This symbol means that it is forbidden to dispose the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authority representative for detailed information on WEEE recycling.

References

• SUNMI - BIoT for Business 4.0
• developer.sunmi.com/docs/read/en-US/maaeghjk480

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>