Kundalini KDLN MINIMAL Floor Lamp Instruction Manual
- June 12, 2024
- Kundalini
Table of Contents
Kundalini KDLN MINIMAL Floor Lamp
Product Information
- Product Name: Minimal
- Manufacturer: David Pompa
- Revision: Rev.02 – March 2022
- Optional Components: Box N.2, Box N.3
- Wiring Diagrams: Provided
- Bulb Type: LED 1 x 3,15W – VF max 9V – 2700K – 410lm
- Feeding Specifications: DC 350mA constant current (not included), Independent use Vout max 60V (SELV) dim. L78xW35xH22 mm
- Manufacturer Contact Information: Kdln Srl Viale L. da Vinci, 277 20090 Trezzano sul Naviglio, Milano T. +39 0236538950 info@kdln.it
- Manufacturer Website: kdln.it
Product Usage Instructions
- Open the product packaging and check if all the components are included.
- If you have purchased optional components (Box N.2, Box N.3), ensure they are also present.
- Refer to the provided wiring diagrams for the installation process.
- If using a DC 350mA constant current, ensure it is not included and needs to be obtained separately.
- For independent use, make sure the Vout does not exceed 60V (SELV) and the dimensions of the power supply are L78xW35xH22 mm.
- Follow the wiring diagram to connect the power supply to the product.
- Place the LED bulb (LED 1 x 3,15W – VF max 9V – 2700K – 410lm) into the appropriate socket.
- If you have purchased optional components (Box N.2, Box N.3), follow the additional instructions provided for their installation.
- Ensure all connections are secure and properly insulated.
- Test the product by turning on the power supply and checking if the LED bulb lights up.
WARNING
Safety is guaranteed by the appropriate use of the following instructions, so
you must keep them. Always disconnect the main voltage before working on the
appliance. Never use abrasive products or aggressive detergents for cleaning
the lamp. If the external cable of this appliance is damaged, it must be
replaced by the manufacturer, its after sales service or other equivalent
qualified person only in order to avoid any danger. Kundalini will not provide
a replacement until the nature of defect has been determined.
BOX N.1
BOX N.2 (optional)
BOX N.3 (optional)
INSTALLATION INSTRUCTION
ASSEMBLY INSTRUCTIONS
Disconnect the mains voltage supply. Pass the feeding cable through the cylinder B and the false ceiling canopy C. Once inserted the feeding cable in the cable clamp D, screw the screws E – Fig.1 -. Attention: it is recommended to do not cut the cable, but to put the excess in the false ceiling. Screw the cylinder B on the body lamp A – Fig.2 -. Drill the false ceiling using a Ø 45 mm hole saw where the lamp is going to be installed. Connect the lamp to a driver in accordance with the technical specifications. If you use the driver F supplied by Kundalini (optional) respect the following instructions. Unscrew the screw and open the driver F – Fig.3 -. Connect the power leads from the grid andthe lamp to the terminal boards of the driver F following the instructions – Fig.4 -. Attention: make sure to respect the lamp cables polarity (”+” black, “-” white). Close again the driver F by screwing the screw. Insert the driver F and thebracket G in the hole of the false ceiling. Adjust the bracket G according to the thickness of the false ceiling panel and fix it using the nut H. Screw the ratchet I over the disc L to lock the structure – Fig.5 -. Reconnect the mains voltage supply.
Canopy (optional)
Disconnect the mains voltage supply. Unscrew the ratchet M to separate the
canopy cover N from the bracket O – Fig.6
- Pass the feeding cable through the ratchet M, the canopy cover N, the central bushing P and the cable clamp Q by unscrewing the screws R. Once inserted the feeding cable in the cable clamp Q, screw the screws R – Fig.7 -. Fix the bracket O using screws and Fischer screws suited to the ceiling characteristics. Connect the power leads from the grid and the lamp to the terminal boards of the driver F following the instructions – Fig.8 -. Connect the earth wire (colour yellow-green) to the specific device following the instructions – Fig.9 -. Reposition the canopy cover N on the bracket O and block by screwing in ratchet M – Fig.10 -. Reconnect the mains voltage supply.
- board LED 1 x 3,15W – VF max 9V – 2700K – 410lm
- DC 350mA constant current (not included)
- Independent use Vout max 60V (SELV) dim. L78xW35xH22 mm
Kdln Srl Viale L. da Vinci, 277 20090 Trezzano sul Naviglio, Milano T. +39 0236538950 info@kdln.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>