BOSCH GWS 18V-15 C Angle Grinder Instruction Manual

GWS Professional
18V-15 C | 18V-15 SC | 18V-15 P | 18V-15 PSC

Original instructions

GWS 18V-15 C Angle Grinder

Safety Instructions

General Power Tool Safety Warnings
**WARNING**
Read all safety warnings, instructions, illustrations and specifica- tions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool. Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
  Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
  Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the  witch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
  Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will dothe job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
  Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.

• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range  specified in the instructions. Charging improperly or attemperatures outside the specified range may damage the battery and increase the risk of fire.
  Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety warnings for angle grinder

• Safety warnings common for grinding, sanding, wire brushing or cutting-off operations: his power tool is intended to function as a grinder, sander, wire brush, hole cutter or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
• Operations such as polishing are not to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
• Do not convert this power tool to operate in a way which is not specifically designed and specified by the tool manufacturer. Such a conversion may result in a loss of control and cause serious personal injury.
• Do not use accessories which are not specifically designed and specified by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
• The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
• The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
• The dimensions of the accessory mounting must fit the dimensions of the mounting hardware of the power tool. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
• Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage  or in- stall an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
• Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various applications. The dust mask or respirator must be capable of filtrating particles generated by the particular application. Prolonged exposure to high intensity noise may cause hearing loss.
• Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal  protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
• Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
• Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
• Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
• Do not operate the power tool near flammable materials. Sparks could ignite these materials.
• Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.

Kickback and related warnings:
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction  opposite of the accessory’s rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb  out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

• Maintain a firm grip with both hands on the power tool and position your body and arms to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.

• Never place your hand near the rotating accessory. Accessory may kickback over your hand.

• Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.

• Use special care when working corners, sharp edges, etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.

• Do not attach a saw chain woodcarving blade, segmented diamond wheel with a peripheral gap greater than 10 mm or toothed saw blade. Such blades create frequent kickback and loss of control. Safety warnings specific for grinding and cutting-off operations:

• Use only wheel types that are specified for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.

• The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An im- properly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.

• The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.

• Wheels must be used only for specified applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

• Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

• Do not use worn down wheels from larger power tools. A wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

• When using dual purpose wheels always use the correct guard for the application being performed. Failure to use the correct guard may not provide the desired level of guarding, which could lead to serious injury. Additional safety warnings specific for  cutting-off operations:

• Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

• Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.

• When the wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold it motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.

• Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.

• Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.

• Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

• Do not attempt to do curved cutting. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage, which can lead to serious injury.
  Safety warnings specific for sanding operations:

• Use proper sized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending too far beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. Safety warnings specific for wire brushing operations:

• Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush The wire bristles can easily penetrate light clothing and/or skin.

• If the use of a guard is specified for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.

Additional safety information

Wear safety goggles.
The protective guard must not be used for cutting. With a suitable adapter, the protective guard can also be used for cutting.
Hold the power tool firmly with both hands and make sure you have a stable footing. The power tool can be more securely guided with both hands.

• For application tools with an internal thread, such as brushes and diamond annular cutters, attention must be paid to the max. thread length of the grinding spindle. The spindle end must not touch the base of the application tool.

• Use suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to explosion. Breaking water pipes causes property damage.

• Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working.

• Release the On/Off switch and set it to the Off position when the power supply is interrupted, e.g. when the battery pack is removed. This prevents uncontrolled restarting.

• Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.

• Store the application tools inside buildings, in a dry, frost-free room at a uniform temperature.

• Remove the application tools before transporting the power tool. This will allow you to avoid damage.

• Bonded cutting and grinding discs have an expiration date, after which the discs must no longer be used.

• In case of damage and improper use of the battery, vapours may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.

• Do not open the battery. There is a risk of short-circuiting.

• The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.

• Only use the battery in the manufacturer’s products or those of the AMPShare partners. This is the only way in which you can protect the battery against dangerous overload.
  Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short- circuiting.

• Caution! When using the power tool with Bluetooth ® , a fault may occur in other devices and systems, aeroplanes and medical devices (e.g. pacemakers, hearing aids). Also, damage to people and animals in the immediate vicinity cannot be completely excluded. Do not use the power tool with Bluetooth® in the vicinity of medical devices, petrol stations, chemical plants, areas with a potentially explosive atmosphere or in blasting areas. Do not use the power tool with Bluetooth® in aircraft. Avoid using the product near your body for extended periods. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Robert Bosch Power Tools GmbH is under license.

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury. Please observe the illustrations at the beginning of this operating manual.

Intended use
The power tool is intended for cutting and brushing metal, stone, plastic and composite materials, roughing metal, plastic and composite materials as well as making holes in stone materials using diamond annular cutters, without the use of water. Make sure that the correct protective guard is used (see “Operation”, page 37). Sufficient dust extraction must be provided when cutting stone. With approved abrasive tools, the power tool can be used for sanding with sanding discs. The power tool must not be used to grind stone materials with diamond grinding heads. With the Bluetooth® Low Energy Module GCY 42 inserted, power tool data and settings can be transferred between the power tool and a mobile device by means of Bluetooth® wireless technology.

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics page.

(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
(3) Spindle lock button
(4) User interface (GWS 18V-15 SC, GWS 18V-15 PSC)
(5) On/off switch (GWS 18V-15 C, GWS 18V-15 SC)
(6) Cover for GCY 42 Bluetooth® Low Energy Module
(7) Rechargeable battery a)
(8) Rechargeable battery release button a)
(9) Standard auxiliary handle (insulated gripping surface) a)
(10) Vibration-damping auxiliary handle (insulated gripping surface)
(11) On/off switch (GWS 18V-15 P, GWS 18V-15 PSC)| (12) Unlocking lever for on/off switch (GWS 18V-15 P, GWS 18V-15 PSC)
(13) Extraction guard for grinding a)
(14) Protective guard for grinding
(15) Protective guard for cutting a)
(16) Cover for cutting
(17) Mounting flange with O‑ring
(18) Carbide grinding head a)
(19) Grinding disc a)
(20) Cutting disc a)
(21) Quick-clamping nut with bar
(22) Grinding spindle| (23) Hand guard a)
(24) Rubber sanding pad a)
(25) Abrasive disc a)
(26) Cup brush a)
(27) Diamond annular cutter a)
(28) Round nut a)
(29) Two-pin spanner for clamping nuta)
(30) Open-ended spanner a)
(31) Handle (insulated gripping surface)
(32) Extraction guard for cutting with cutting guides a)
(33) Diamond cutting disc a)| (34) Disc brush (dia. 22.22 mm) a)
(35) Disc brush (M14) a)
(36) Conical brush a)
(37) Battery charge indicator (user interface)
(38) Kickback shutdown indicator (user interface)
(39) Speed preselection button (user interface)
(40) Speed setting/mode indicator (user interface)
(41) Smartphone symbol (user interface)
(42) Power tool status indicator (user interface)
(43) Temperature indicator (user interface)
a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
---|---|---|---

Technical Data

An : le : rinder| | GWS 18V-15 C| GWS 18V-15 SC|
---|---|---|---|---
•WS 18V-15 SC
Article number| | 3 601 JH6 0..| 3 601 JH6 1..| 3 601 JH6 3..
Rated voltage| V=| 18| 18| 18
Rated speed’)| min.’| 11,000| 11,000| 8500
No-load speeds’| min’| 9800| 3400-9800| 2600-7400
Max. grinding disc diameter/rubber sanding pad diameter| mm| 125| 125| 150
Grinding spindle thread| | M 14| M 14| M 14
Max. thread length of grinding spindle| mm| 22| 22| 22
Kickback stop| | •| •| •
Restart protection| | •| •| •
Run-out brake| | •| •| •
Speed preselection| | –| •| •
Weight according to EPTA-Procedure 01:2014`1| kg| 2.4-3.7| 2.5-3.8| 2.5-3.9
Recommended ambient temperature during charging| °C| 0 to +35| 0 to +35| 0 to +35
Permitted ambient temperature during operatioeland dur- ing storage| °C| -20 to +50| -20 to +50| -20 to +50
Compatible rechargeable batteries| | GBA 18V… ProCORE18V…| GBA 18V… ProCORE18V…| GBA 18V… ProCORE18V…
Recommended rechargeable batteries for maximum per- formance| | ProCORE18V… ? 5.5 Ah| ProCORE18V…5.5 Ah| ProCORE18V…? 5.5 Ah
Recommended chargers| | GAL 18… GAX 18… GAL 36…| GAL 18… GAX 18… GAL 36…| GAL 18… GAX 18… GAL 36…
Angle grinder| | | |
Data transfer| | GWS 18V-15 C| GWS 18V-15 SC| GWS 18V-15 SC
Bluetooth®E)| | Bluetooth®4.2(Low Energy)| Bluetooth®4.2(Low Energy)| Bluetooth®4.2(Low Energy)
Signal interval| s| 8| 8| 8
Max. signal range F)| m| 30| 30| 30

A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual no-load speed is lower for safety reasons and according to production tolerances.
B) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah and depending on the battery’s state of charge as well as the tool’s operating temperature
C) Depends on rechargeable battery (7), protective guard ((15), (14), (16)) and auxiliary handle ((9), (10)) in use
D) Limited performance at temperatures < 0 °C
E) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.2) and support the Generic Access Profile (GAP).
F) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be significantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).

ProCORE18V…
Recommended rechargeable batteries for maximum performance| | ProCORE18V…5.5 Ah| ProCORE18V… 5.5 Ah
Recommended chargers| | GAL 18… GAX 18… GAL 36…| GAL 18… GM 18… GAL 36…
Data transfer| | |
Bluetootfrl’E’| | –| BluetootP4.2 (Low Energy)
Signal interval| s| –| 8

Max. signal range 30
A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual no-load speed is lower for safety reasons and according to production tolerances.
B) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah and depending on the battery’s state of charge as well as the tool’s operating temperature
C) Depends on rechargeable battery (7), protective guard ((15), (14), (16)) and auxiliary handle ((9), (10)) in use
D) Limited performance at temperatures < 0 °C
E) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.2) and support the Generic Access Profile (GAP).
F) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be significantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases,etc.).
Noise/Vibration Information

Noise emission values determined according to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is
Vibration total values ah (triax vector sum) and uncertainty K determined according to EN IEC 62841-2-3:
Surface grinding and abrasive cutting:

Noise emission values determined according to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN IEC 62841-2-3:
Surface grinding and abrasive cutting:

Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission value to increase by up to 15 dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise emissions must be taken into consideration, both for the risk assessment of the noise output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these instructions have been measured in accordance with a standardised measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions. The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different application tools or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period. To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account. This may significantly reduce vibration and noise emissions over the total working period. Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organising workflows correctly.
Kickback stop
If there is a sudden kickback in the power tool, e.g. jamming in a separating cut, the power supply to the motor will be interrupted electronically. The kickback stop indicator(38) then lights up. When kickback stop is activ- ated, the status indicator (42) flashes red. To restart the tool, set the on/off switch (5) / (11) to the “off” position and then switch the power tool on again.
Run-out brake
The power tool is fitted with the electronic Bosch Brake System. When it is switched off, the abrasive tool is brought to a complete stop within a few seconds. This means that the runout time is significantly shorter than for angle grinders without a run-out brake and enables the power tool to be set down sooner.
Restart protection
The restart protection feature prevents the power tool from starting unintentionally after the power supply to it has been interrupted.
When restart protection is activated, the status indicator (42) flashes red.
To restart the tool, set the on/off switch (5) / (11) to the “off” position and then switch the power tool on again.
Impact shutdown
The integrated impact shutdown switches the power tool off as soon as it hits the floor. The status indicator (42) then flashes red.
To restart the tool, set the on/off switch (5) / (11) to the “off” position and then switch the power tool on again.
User interface (see figure E)
(GWS 18V-15 SC / GWS 18V-15 PSC) The user interface (4) is used to preselect the speed and to indicate the status of the power tool.

Speed preselection

(GWS 18V-15 SC / GWS 18V-15 PSC)
In the default setting, 3 speed levels are preset. A special application (Bosch Toolbox App) can be used to program up to 6 speed levels.
If the number of speed levels is changed, the values of the individual levels are adjusted by default. In this case, the speed level/mode indicator (40) lights up white. When a speed value is programmed individually, the speed level/mode indicator (40) lights up blue at this speed level (i.e. not according to a default setting). The individual adaptation of speed levels is possible in steps of 200 min -1 each. Observe the ascending logic of the steps (2 ≥ 1 / 3 ≥ 2 etc).
The information in the tables below describes the preset speeds (default settings) for each programmed number of levels.

GWS 18V-15 SC GWS 18V-15 PSC (125 mm)| Basic speed setting at level| | |
---|---|---|---|---
1| 23| 4| 5| 6
[min| [min’] [min’]| [min’]| [min’]| [min’]
Number of speed settings| –| –| | | –
2| 3400| 9800| –| –| –
3| 3400| 66009800| –| –| –
4| 3400| 56007600| 9800| –| –
5| 3400| 50006600| 8200| 9800| –
GWS 18V-15 SC GWS 18V-15 PSC (125 mm)| Basic speed setting at level
---|---
1| 2| 3| 4| 5| 6
[min -1 ]| [min -1 ]| [min -1 ]| [min-1]| [min -1 ]| [min -1 ]
Number of speed settings| | | | |
6| 3400| 4600| 6000| 7200| 8600| 9800

The specified speed setting values depend on the rechargeable battery in use, the battery’s state of charge and the tool’s operating temperature.

GWS 18V-15 SC
(150 mm)| Basic speed setting at level
---|---
1| 2| 3| 4| 5| 6
[min -1 ]| [min -1 ]| [min -1 ]| [min -1 ]| [min -1 ]| [min -1 ]
Number of speed settings| | | | |
2| 2600| 7400| –| –| –| –
3| 2600| 5000| 7400| –| –| –
4| 2600| 4200| 5800| 7400| –| –
5| 2600| 3800| 5000| 6200| 7400| –
6| 2600| 3600| 4600| 5400| 6400| 7400

The specified speed setting values depend on the rechargeable battery in use, the battery’s state of charge and the tool’s operating temperature.
You can use the button for speed preselection (39) to preselect the required speed, even during operation. The information in the table below describes the recommended values for the default settings with 3 preset speed levels.

Material| Application| Application tool| Speed preselection level| GWS 18V•15 SC GWS 18V•15 PSC (125 mm)[mini| GWS 18V•15 SC (150 mm)
[mini
---|---|---|---|---|---
Metal| Removing paint| Sanding sheet| 1| 3400| 2600
Metal| Brushing, removing rust| Cup brush, abrasive disc| 1| 3400| 2600
Stainless steel| Grinding| Grinding disc/fibre disc| 2| 6600| 5000
Metal| Rough grinding| Grinding disc| 3| max.| max.
Metal| Cutting| Cutting disc| 3| max.| max.
Stone| Cutting| Diamond cutting disc| 3| max.| max.

• The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.

Rechargeable battery
Bosch sells some cordless power tools without a rechargeable battery. You can tell whether a rechargeable battery is included with the power tool by looking at the packaging.
Charging the battery

• Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.
  Note: Lithium-ion rechargeable batteries are supplied partially charged according to international transport regula- tions. To ensure full rechargeable battery capacity, fully charge the rechargeable battery before using your tool for the first time.

Inserting the Battery
Push the charged battery into the battery holder until it clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery release button and pull the battery out.
Do not use force to do this.
The rechargeable battery has two locking levels to prevent the battery from falling out if the battery release button is pressed unintentionally. The rechargeable battery is held in place by a spring when fitted in the power tool.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the state of charge of the battery. For safety reasons, it is only possible to check the state of charge when the power tool is not in operation. Press the button for the battery charge indicator  or to show the state of charge. This is also possible when the battery is removed. If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced. The state of charge of the battery is also displayed on the user interface (see “Status indicators”, page 39).
Battery model GBA 18V…

Battery model ProCORE18V…

Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to 50 °C. Do not leave the battery in your car in the summer, for example. Occasionally clean the ventilation slots on the battery using a soft brush that is clean and dry. A significantly reduced operating time after charging indicates that the battery has deteriorated and must be replaced. Follow the instructions on correct disposal.

Fitting

Using the GCY 42 Bluetooth® Low Energy Module
Note: The Bluetooth® Low Energy Module GCY 42 is avail- able as an accessory with GWS 18V-15 C power tools; it is included in the scope of delivery for GWS 18V-15 SC and GWS 18V-15 PSC power tools. Read the corresponding operating instructions for information about the Bluetooth® Low Energy Module GCY 42.
Fitting Protective Equipment
Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
Note: If the grinding disc breaks during operation or  the holding fixtures on the protective guard/power toolbecome damaged, the power tool must be sent to the after-sales service immediately; see the “After-Sales Service and Application Service” section for addresses.
Protective guard for grinding

Place the protective guard (14) onto the holder on the power tool until the coding cams of the protective guard are aligned with the holder. When doing so, press and hold the unlocking lever (1). Press the protective guard (14) onto the spindle collar until the shoulder of the protective guard is sitting on the flange of the power tool and rotate the protective guard until it audibly clicks into place.
Adjust the position of the protective guard (14) to meet the requirements of the operation. To do this, push the unlocking lever (1) upward and rotate the protective guard (14) into the required position.

• Always position the protective guard (14) such that the two cams on the unlocking lever  (1) engage in the corresponding openings on the protective guard  (14).
• Adjust the protective guard (14) such that sparking in the direction of the operator is prevented.
• The protective guard (14) must only be adjustable while the unlocking lever (1) is actuated. Otherwise, the power tool must not be used any more under any circumstances and must be sent to the after-sales service.
  Note:
  The coding cams on the protective guard (14) ensure that only a protective guard that is suitable for the power tool can be fitted.

Extraction guard for sanding
The extraction guard (13) can be used to minimise dust when sanding paint, varnish and plastics in conjunction with the carbide grinding head (18). The extraction guard (13) is not suitable for working metals. A suitable Bosch vacuum cleaner can be connected to the extraction guard (13). The extraction guard (13) is mounted in the same manner as the protective guard (14). The brush collar can be replaced. Protective guard for cutting .For cutting, always use the protective guard for cutting (15) or the protective guard for grinding  (14) together with the cover for cutting (16). Provide sufficient dust extraction when cutting stone. The protective guard for cutting (15) is fitted in the same way as the protective guard for grinding (14). Metal cover for cutting Fit the metal cover for cutting (16) on the protective guard for grinding (14) (see figure A): Swivel the tool retainer back (➊). Attach the cover (16) to the protective guard for grinding (14) (➋). Press the tool retainer firmly into place on the protective guard (14) (➌). To remove the cover (see figure B), press the button on the tool retainer (➊) and swivel it back (➋). Remove the cover (16) from the protective guard (14) (➌).
Plastic cover for cutting
Attach the plastic cover for cutting (16) to the protective guard for grinding (14) (see figure C). The cover (16) audibly and visually engages on the protective guard (14). To remove the cover (see figure D), unlock the cover (16) on the left- or right-hand side of the  protective guard (14) (➊) and remove the cover (➋). Extraction guard for cutting with a guide block The extraction guard for cutting with a cutting guide (32) is fitted in the same way as the protective guard for grinding. By securing the auxiliary handle (9)/(10) with the clip through the extraction guard on the gearbox housing, the power tool is firmly attached to the extraction guard. A suitable Bosch dust extractor can be connected to the extraction guard with a cutting guide (32). To do so, insert the vacuum hose with dust extraction adapter into the provided receiving connection of the extraction guard.
Note: The friction generated by the dust in the vacuum hose and accessory during extraction causes an electrostatic charge that the user may experience as static discharge (depending on environmental factors and their physiological state). Bosch generally recommends using an anti-static vacuum hose (accessory) to vacuum up fine dust and dry materials.
Hand guard

• Always fit the hand guard (23) when working with the rubber sanding pad (24) or with the cup brush/conical brush/diamond annular cutter. Attach the hand guard (23) to the auxiliary handle (9)/(10).Standard auxiliary handle/low-vibration auxiliary handle Screw the auxiliary handle (9)/(10) on the right or left of the machine head depending on the working method.

• Do not operate your power tool without the auxiliary handle (9)/(10).

• Do not continue to use the power tool if the auxiliary handle (9)/(10) is damaged. Do not make any alterations to the auxiliary handle (9)/(10).
  The low- vibration auxiliary handle (10) reduces vibration, enabling the tool to be used safely and more com- fortably.
  Fitting the Abrasive Tools

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

• Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working. Clean the grinding spindle (22) and all the parts to be fitted. Lock the grinding spindle with the spindle lock button (3) before clamping and releasing the abrasive tools.

• Do not press the spindle lock button while the grinding spindle is moving. The power tool may become damaged if you do this.

Grinding/Cutting Disc
Pay attention to the dimensions of the abrasive tools. The diameter of the hole must match that of the hub flange. Do not use an adapter or reducer.
When using diamond cutting discs, ensure that the arrow indicating the direction of rotation on the diamond cutting disc matches the direction of rotation of the power tool (see the direction of rotation arrow on the machine head).
See the graphics page for fitting instructions.
Use the quick-clamping nut (21) to secure the grinding/cutting disc without the need for additional tools.
Note:
When assembling bonded grinding or cutting discs using the supplied mounting flange (17) and the quick-clamping nut (21), the use of intermediate layers is not necessary.
To secure the grinding/cutting disc, place the mounting flange with O-ring (17) on the grinding spindle (22) and screw on the quick-clamping nut (21). Only use the quick-clamping nut (21) for grinding/cutting discs up to a maximum diameter of 150 mm.

• The quick-clamping nut (21) may be used only for grinding or cutting discs.

• Only use quick-clamping nuts (21) that are in good working order and not damaged.

• When screwing on, make sure that the printed side of the quick-clamping nut (21) is not facing the grinding disc.

•  Always secure a grinding/cutting disc using only the quick-clamping nut (21) supplied.Press the spindle lock button (3) to lock the grinding spindle. To tighten  the quick-clamping nut (21), fold up the bar and turn the quick-clamping nut firmly clockwise. Then fold down the bar to secure the  quickclamping nut. It is not sufficient to tighten  the disc along the edge.Quick-clamping nuts (21) that are properly secured and not damaged can be removed by hand. To do this, fold up the bar and turn the quick-clamping nut firmly anticlockwise. If the quickclamping nut is stuck, do not attempt to loosen it with a tool – always use a twopin spanner.After fitting the mounting flange and the grinding/cutting disc, the free  thread length of the grinding spindle must be at least 4 mm. Ensure that the abrasive tool is firmly seated, so that it does not twist away from the spindle in the runout of the power tool.
  A plastic part (O-ring) is fitted around the centring collar in the mounting flange (17). If the O-ring is missing or damaged, the mounting flange (17) must be replaced before operation can resume.

• After fitting the abrasive tool, check that the abrasive tool is fitted correctly and can turn freely before switching on the power tool. Make sure that the abrasive tool does not brush against the protective guard or other parts.

Approved abrasive tools
You can use all the abrasive tools mentioned in these operating instructions.
The permissible speed [min -1  ] or the circumferential speed[m/s] of the abrasive tools used must at least match the val- ues given in the table.
It is therefore important to observe the permissible rotational/circumferential speed on the label of the abrasive tool.

Max. [mm]| | [mm]| [°]| |
---|---|---|---|---|---
D| b| s| d| α| [min -1 ]| [m/s]
125| 7.2| –| 22.2| –| 11,000| 80
150| 7.2| –| 22.2| –| 8500| 80
125| –| –| –| –| 11,000| 80
150| –| –| –| –| 8500| 80
75| 30| –| M 14| –| 11,000| 80
125| 24| –| M 14| –| 11,000| 80
125| 19| –| 22| –| 11,000| 80
150| 24| –| M 14| –| 8500| 80
150| 19| –| 22| –| 8500| 80
125| –| –| M 14| –| 11,000| 80
83| –| –| M 14| –| 11,000| 80
125| 6| 10| 22| > 0| 11,000| 80
150| 6| 10| 22| > 0| 8500| 80
125| 21| –| 22| –| 11,000| 80

Rotating the machine head (see figure F)

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
  The machine head can be rotated in 90° increments. In this way, the on/off switch can be brought into a more favourable handling position for particular applications, e.g. for lefthanded tool users.
  Completely unscrew the four screws (➊). Rotate the machine head carefully, without removing it from the housing, into the new position (➋). Screw in and retighten the four screws (➌). Dust/Chip Extraction Dust from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health. Touching or breathing-in the dust can cause allergic reactions and/or lead to respiratory infections of the user or bystanders. Certain dust, such as oak or beech dust, is considered carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials containing asbestos may only be worked by specialists. – Provide for good ventilation of the working place. – It is recommended to wear a P2 filter-class respirator. Observe the relevant regulations in your country for the materials to be worked.

• Avoid dust accumulation at the workplace. Dust can easily ignite.

Operation

• Do not load the power tool so heavily that it comes to a stop.

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

• Exercise caution when cutting slots in structural walls; see the “Information on structural design” section.

• Clamp the workpiece if it is not secure under its own weight.

• If the power tool has been subjected to a heavy load, continue to run it at no-load for several minutes to cool down the accessory.

• Do not use the power tool with a cut-off stand.

• Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working.
  Working   advice
  Rough grinding

• Always use the protective guard for grinding (14) when rough grinding with bonded abrasives.

• Never use cutting discs for rough grinding.

• When rough grinding, the protective guard for cutting (15) or the protective guard for grinding (14) with a fitted cover for cutting (16) can impact the workpiece and lead to a loss of control. The best rough grinding results are achieved with a set angle of 30° to 40°. Move the power tool back and forth with moderate pressure. This will ensure that the workpiece does not become too hot or discolour and that grooves are not formed.

• The protective guard for cutting (15) or the protective guard for grinding (14) with a fitted cover for cutting (16) must be used when using bonded discs which are approved for cutting and grinding.37
  Surface grinding with flap disc

• Always use the protective guard for grinding (14) when grinding with the flap disc. The flap disc (accessory) enables you to machine curved surfaces and profiles. Flap discs have a considerably longer service life, lower noise levels and lower grinding  temperatures than conventional grinding discs.
  Surface grinding with sanding disc

• Always fit the hand guard (23) when working with the rubber sanding pad (24). Grinding with a sanding disc can be done without a protective guard. See the graphics page for fitting instructions. Screw on the round nut (28) and tighten it with the two-pin spanner. Cup brush/disc brush/conical brush Always use the protective guard for grinding (14) when brushing with disc brushes. Brushing with cup brushes/conical brushes can be performed without the protective guard.

• Always fit the hand guard (23) when working with the cup brush or conical brush.

• The wires of the disc brush can get caught on the protective guard and break, if the maximum permitted dimensions of the disc brushes are exceeded.
  See the graphics page for fitting instructions.
  The cup brush/conical brush/disc brush with M14 thread must be screwed onto the grinding spindle until it rests firmly against the grinding spindle flange at the end of the grinding spindle thread. Tighten the cup brush/conical brush/disc brush with an open-ended spanner.
  To fasten the disc brush with a diameter of 22.22 mm, attach the mounting flange with O-ring (17) to the grinding spindle (22), screw on the round nut (28) and tighten with the two-pin spanner.
  Cutting Metal

• For cutting metal with bonded cutting discs or diamond cutting discs, always use the protective guard for cutting (15) or the protective guard for grinding (14) with a fitted cover for cutting (16).

• When using the protective guard for grinding (14) for cutting work with bonded cutting discs, there is an increased risk of being exposed to sparks, particles and disc fragments if the disc breaks. When carrying out abrasive cutting, use a moderate feed that is suited to the material being machined. Do not exert pressure on the cutting disc and do not tilt or swing the power tool. Do not attempt to reduce the speed of a cutting disc coming to a stop by applying pressure from the side. The power tool must always work in an up-grinding motion. Otherwise there is a risk that it will be pushed uncontrolled out of the cut. For best results when cutting profiles and rectangular tubing, start at the smallest cross section.
  Cutting stone

• For cutting stone with bonded cutting discs or diamond cutting discs for concrete/stone, always use the extraction guard for cutting with a cutting guide (32) or the protective guard for cutting (15) or the protective guard for grinding (14) with a fitted cover for cutting (16).

• Provide sufficient dust extraction when cutting stone.

• Wear a dust mask.

• The power tool may be used only for dry cutting/grinding.

• When using the protective guard for cutting (15) , the protective guard for grinding (14) or the protective guard for grinding (14) with a fitted cover for cutting (16) for cutting and grinding applications in concrete or masonry, there is an increased dust load and an increased risk of losing control of the power tool, which can lead to kickback.

For cutting stone, it is best to use a diamond cutting disc.
When using the extraction guard for cutting with a cutting guide (32), the dust extractor must be approved for extracting stone dust. Suitable dust extractors are available from Bosch.

Switch on the power tool and position it with the front part of the cutting guide on the workpiece. Move the power tool with a moderate feed motion that is suited to the material being machined. When cutting especially hard materials such as con crete with a high pebble content, the diamond cutting disc can overheat and become damaged as a result. This is clearly indicated by circular sparking, rotating with the diamond cutting disc. If this happens, stop cutting and allow the diamond cutting disc to cool down by running the power tool for a short time at maximum speed with no load. If work is noticeably slower and with circular sparking, this indicates that the diamond cutting disc has become blunt. You can resharpen the disc by briefly cutting into abrasive material (e.g. lime-sand brick).
Cutting other materials

• For cutting materials such as plastic, composite materials, etc. with bonded cutting discs or Carbide Multi Wheel cutting discs, always use the protective guard for cutting (15) or the protective guard for grinding (14) with a fitted cover for cutting  (16). You
  can achieve improved dust extraction by using the extraction guard with a cutting guide (32). Working with Diamond Annular Cutters

• Only use dry diamond annular cutters.

• Always fit the hand guard (23) when working with diamond annular cutters.
  Do not place the diamond annular cutter parallel to the workpiece. Plunge it into the workpiece at an angle and in a circular motion. This will allow you to achieve optimal cooling and ensure a longer tool life for the diamond annular cutter.
  Information on structural design
  Recesses in load-bearing walls are subject to country-specific regulations. These regulations must be observed under all circumstances. Seek advice from the responsible structural engineer, architect or construction supervisor before starting work.

Start-Up
Switching on/off
(GWS 18V-15 C / GWS 18V-15 SC)
To start the power tool, push the on/off switch (5) forward.
To lock the on/off switch (5) in position, push the on/off switch (5) forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (5); or, if the switch is locked, briefly push the on/off switch (5) backward and down and then release it.

• Always check abrasive tools before using them. The abrasive tool must be fitted properly and be able to move freely. Carry out a test run for at least one minute with no load. Do not use abrasive tools that are damaged, run untrue or vibrate during use. Damaged abrasive tools can burst apart and cause injuries. Switching On/Off (GWS 18V-15 P / GWS 18V-15 PSC)

To start the power tool, push the unlocking lever (12) forwards and then push the on/off switch (11) up.
To switch off the power tool, release the on/off switch (11). Always check abrasive tools before using them. The abrasive tool must be fitted properly and be able to move freely. Carry out a test run for at least one minute with no load. Do not use abrasive tools that are Status indicators damaged, run untrue or vibrate during use. Damaged abrasive tools can burst apart and cause injuries.

Battery charge indicator
(user interface) (37)

| Meaning/cause|

Solution

---|---|---
Green| Battery charged| –
Yellow| Battery almost empty| Replace or charge battery soon
Red| Battery empty| Replace or charge battery
| |

Power tool status indicator 42

| Meaning/cause|

Solution

Green| Status OK| –
Yellow| Critical temperature has been reached or bat- tery is almost empty| Run the power tool at no load and allow it to cool down, or replace or charge the battery soon
Illuminated red| Power tool has overheated or battery is empty| Allow the power tool to cool down, or replace or charge the battery
Flashing red| Kickback shutdown, restart protection or im- pact shutdown has been triggered| Turn the power tool off and on again
Flashing blue| Power tool is connected to a mobile device or settings are being transferred| –
| |

Temperature indicator (43)

| Meaning/cause|

Solution

Yellow| Critical temperature has been reached (mo- tor, electronics, battery)| Run the power tool at no load and allow it to cool down
Red| Power tool is overheated and will switch off| Leave the power tool to cool down
| |
Smartphone symbol (41)| Meaning/cause|
| Further information can be found under the “Puwer tool status” display on a mobile device if it is connected via Bluetooth® wireless technology.

Connectivity functions
In conjunction with the Bluetooth® Low Energy Module GCY 42, the following connectivity functions are available for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for information about the Bluetooth® Low Energy Module GCY 42.
The connection of the power tool with the app must be confirmed by pressing the speed preselection button (39)  onthe user interface (4). The app requests this when connecting.

Maintenance and Service

Maintenance and Cleaning

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be re- moved for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean. Store and handle the accessories carefully.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories. In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at: www.bosch- pt.com/serviceaddresses

Transport
The recommended lithium-ion batteries are subject to legislation on the transport of dangerous goods. The user can transport the batteries by road without further requirements.
When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.
Disposal
Power tools, rechargeable batteries, accessories and packaging should be sorted for environmental-friendly recycling.
Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.
Only for United Kingdom:
According to Waste Electrical and Electronic Equipment Regulations 2013 (2013/3113) and the Waste Batteries and Accumulators Regulations 2009 (2009/890), power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.
Battery packs/batteries: Li-ion:
Please observe the notes in the section on transport (see “Transport”, page 40).

Licenses

Copyright © 2004 – 2020, Texas Instruments Incorporated
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
– Neither the name of Texas Instruments Incorporated nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2009–2020 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
– Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Copyright © 2011 Petteri Aimonen
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.

EU Declaration of Conformity
Angle grinder
Article number
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards. Technical file at: *

GWS 18V-15 C
GWS 18V-15 SC
GWS 18V-15 SC
GWS 18V-15 P
GWS 18V-15 PSC| 3 601 JH6 002
3 601 JH6 102
3 601 JH6 303
3 601 JH6 A02
3 601 JH6 B02| 2006/42/EC
2014/30/EU
2011/65/EU| EN 62841-1:2015
EN IEC 62841-2-3:2021+A11:2021
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
---|---|---|---
| * Robert Bosch Power Tools GmbH
(PT/ECS) 70538 Stuttgart GERMANY
Henk Becker
Chairman of Executive
Management| Helmut Heinzelmann
Head of Product Certification
Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 01.02.2022

Declaration of Conformity

We declare under our sole responsibility that the stated products comply with all applicable provisions of the regulations listed below and are in conformity with the following standards.
Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom

| The Supply of Machinery (Safety) Regulations 2008
The Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
EN 62841-1:2015
EN IEC 62841-2-3:2021+A11:2021
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
---|---
| Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany
represented (in terms of the above regulations) by Robert Bosch Limited, Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom
Vonjy Rajakoba
Managing Director – Bosch UK| Martin Sibley
Head of Sales Operations and Aftersales

Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorised representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com

Documents / Resources

| BOSCH GWS 18V-15 C Angle Grinder [pdf] Instruction Manual
GWS 18V-15 C, GWS 18V-15 SC, GWS 18V-15 P, GWS 18V-15 PSC, GWS 18V-15 C Professional, GWS 18V-15 SC Professional, GWS 18V-15 P Professional, GWS 18V-15 PSC Professional, GWS 18V-15 C Angle Grinder, Angle Grinder, Grinder
---|---

References

• Invented for life | Bosch Global
• Početna strana | Bosch u Srbiji
• Skånevik Ølen Kraftlag AS
• Електроінструменти Bosch | Bosch Professional
• Электроинструменты Bosch | Bosch Professional
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Електроинструменти на Bosch | Електроинструменти на Bosch
• Service worldwide
• Home | Bosch Power Tools
• Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Home | Bosch Power Tools
• Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
• Elektronarzędzia Bosch | Elektronarzędzia Bosch
• Scule electrice Bosch | Scule electrice Bosch
• Bosch električni alati | Bosch električni alati
• Bosch Услуги | Электроинструменты Bosch
• Elektrické náradie Bosch | Elektrické náradie Bosch
• Invented for life | Bosch Global
• Ana Sayfa | Bosch Türkiye
• Početna | Bosch u Hrvatskoj
• herramientasbosch.net

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>