VELOSSA TECH 2016-2020+ Infiniti Q50 Red Sport BIG MOUTH Ram Air Intake Installation Guide
- August 25, 2024
- VELOSSA TECH
Table of Contents
VELOSSA TECH 2016-2020+ Infiniti Q50 Red Sport BIG MOUTH Ram Air Intake
Specifications:
- Product : Infiniti Q50 Red Sport BIG MOUTH Ram Air Intake
- Year Range: 2016-2020+
Product Usage Instructions
Kit Contents:
Review the document before installation. You will need basic hand tools and
about 1-1.5 hours for installation.
Bumper Removal:
- Search for a bumper removal guide for Infiniti Q60 on YouTube.
- Follow the steps for bumper removal (same steps for Q50).
Retainer Clip Removal:
Pinch the wire loom retainer clips to remove the wire looms from the metal
frame on both sides.
Horn Reorientation:
- Remove the bolt (10mm) to adjust the horn mount position.
- Use supplied M5 hardware to fasten the L-Bracket and tighten the lock nut to 50 in-lb.
- Secure the horn to L-bracket and reuse OEM bolt with washers.
Pump Reorientation:
- Undo clip retaining wire loom for pump shield and remove nuts that hold the shield.
- Reorient the pump and assemble according to provided instructions.
- Ensure pump does not touch the crash bar and secure it to the car using OEM nuts with supplied foam strip.
Kit Contents
Please review this document before attempting installation. You will need basic hand tools and about 1-1.5 hours of installation time. Please review the table below and make sure you have received the kit contents.
Bumper Removal
Perform a YouTube Search using the term “How To Remove Your Infiniti Q60’s
Front Bumper Properly” and follow the steps for bumper removal (same steps for
Q50). Once you remove the bumper, please continue with this installation guide
Retainer Clip Removal
Pinch the wire loom retainer clips as shown and remove the wire looms from
the metal frame. Do this to both sides.
Horn Reorientation
If your OEM horn looks like the one in (A), horn will need to be rotated. Remove bolt, loosen the central nut and rotate it 90° so the shield is pointing opposite the mounting bracket. If your OEM horn looks like the one in (B), simply remove the bolt.
Use the supplied M5 hardware to fasten the L-Bracket as shown below. Tighten the lock nut to a torque spec of 50 in-lb. Place 2 large M6 washers behind bracket and reuse OEM bolt.
Fasten the L-Bracket to the OEM horn mounting hole.
Pump Reorientation
Undo clip that retains the wire loom for the pump shield. Then remove the nuts that retain the shield. The shield will not be reused.
Shown below is the water pump after being reoriented, the following slides will outline the process.
The first step is to group the aluminum bracket with the “F” (Front) block as shown below. Use the supplied M6x40 screws and 2 large washers to keep the assembly in place but do not fasten yet.
The next step is to position the pump mounting bracket behind the “F” block. Do not fasten yet.
Lastly, slide the “B” (Back) block onto the assembly and fasten using a large M6 washer and M6 lock nut on each screw. DO NOT OVERTIGHTEN.
IT IS CRITICAL THAT THE PUMP NOT TOUCH THE CRASH BAR. The aluminum bracket holes are slightly oversized to allow for small adjustment; use as needed.
Once the correct position for the pump has been chosen, fasten the pump assembly to the car using the OEM nuts. Apply the supplied foam strip onto the pump on the area indicated below.
Pump Reorientation Overview
After the pump has been reoriented, it should have a slight forward tilt.
BIG MOUTH Installation
If your stock heat exchanger has this small shroud located on the driver side, remove it by extracting the indicated pop clips.
Insert the BIG MOUTH in an upward sweeping motion as indicated. Align the holes and use the supplied M6 x 30mm bolts + 6mm large washers (front) and M6 locknuts (rear) to fasten. Turn by hand at first in order to avoid cross threading, use a 5mm hex key and 10mm wrench for tightening. Install both BIG MOUTH intakes this way.
Finalize
Re-install the bumper the same way it was removed and ENJOY!
FAQ
Q: How long does it take to install the Infiniti Q50 Red Sport BIG MOUTH
Ram Air Intake?
A: The installation typically takes about 1-1.5 hours with basic hand tools.
Q: Do I need any special tools for the installation?
A: Basic hand tools are required for the installation process.
Q: What year range is the Infiniti Q50 Red Sport BIG MOUTH Ram Air Intake
compatible with?
A: The product is compatible with Infiniti Q50 models from 2016 to 2020 and
newer.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>