TRINAMIC TMCM-1140 Single Axis Stepper Motor Controller/Driver Module User Manual
- June 12, 2024
- TRINAMIC
Table of Contents
- TMCM-1140 Single Axis Stepper Motor Controller/Driver Module
- Features
- Order Codes
- Mechanical and Electrical Interfacing
- Motor driver current
- Reset to Factory Defaults
- On-Board LEDs
- Operational Ratings
- Functional Description
- TMCM-1140 Operational Description
- Life Support Policy
- Revision History
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MODULE FOR STEPPER MOTORS MODULE
Hardware Version V1.3
HARDWARE MANUAL
TMCM-1140
1-Axis Stepper Controller / Driver
2 A / 24 V sensOstep™ Encoder
USB, RS485, and CAN
TMCM-1140 Single Axis Stepper Motor Controller/Driver Module
UNIQUE FEATURES:
coolStep™
Features
The TMCM-1140 is a single axis controller/driver module for 2-phase bipolar stepper motors with state of the art feature set. It is highly integrated, offers a convenient handling and can be used in many decentralized applications. The module can be mounted on the back of NEMA 17 (42mm flange size) stepper motors and has been designed for coil currents up to 2 A RMS and 24 V DC supply voltage. With its high energy efficiency from TRINAMIC’s coolStep™ technology cost for power consumption is kept down. The TMCL™ firmware allows for both, standalone operation and direct mode.
MAIN CHARACTERISTICS
- Motion controller
- Motion profile calculation in real-time
- On the fly alteration of motor parameters (e.g. position, velocity, acceleration)
- High performance microcontroller for overall system control and serial communication protocol handling
Bipolar stepper motor driver
- Up to 256 microsteps per full step
- High-efficient operation, low power dissipation
- Dynamic current control
- Integrated protection
- stallGuard2 feature for stall detection
- coolStep feature for reduced power consumption and heat dissipation
Encoder
sensOstep magnetic encoder (1024 increments per rotation) e.g. for step-loss
detection under all operating conditions and positioning supervision
Interfaces
-
RS485 2-wire communication interface
-
CAN 2.0B communication interface
-
USB full speed (12Mbit/s) device interface
-
4 multipurpose inputs:
– 3x general-purpose digital inputs -
(Alternate functions: STOP_L / STOP_R / HOME switch inputs or A/B/N encoder input)
– 1x dedicated analog input -
2 general purpose outputs
– 1x open-drain 1A max.
– 1x +5V supply output (can be switched on/off in software)
Software
- TMCL: standalone operation or remote controlled operation, program memory (non volatile) for up to 2048 TMCL commands, and PC-based application development software TMCL-IDE available for free.
Electrical and mechanical data
- Supply voltage: +24 V DC nominal (9… 28 V DC)
- Motor current: up to 2 A RMS / 2.8 A peak (programmable)
Refer to separate TMCL Firmware Manual, too.
TRINAMICS UNIQUE FEATURES – EASY TO USE WITH TMCL
stallGuard2™ stallGuard2 is a high-precision sensorless load measurement using the back EMF on the coils. It can be used for stall detection as well as other uses at loads below those which stall the motor. The stallGuard2 measurement value changes linearly over a wide range of load, velocity, and current settings. At maximum motor load, the value goes to zero or near to zero. This is the most energy efficient point of operation for the motor.
coolStep™ coolStep is a load-adaptive automatic current scaling based on the load measurement via stallGuard2 adapting the required current to the load. Energy consumption can be reduced by as much as 75%. coolStep allows substantial energy savings, especially for motors which see varying loads or operate at a high duty cycle. Because a stepper motor application needs to work with a torque reserve of 30% to 50%, even a constant-load application allows significant energy savings because coolStep automatically enables torque reserve when required. Reducing power consumption keeps the system cooler, increases motor life, and allows reducing cost.
Order Codes
Order code | Description | Size (mm 3) |
---|---|---|
TMCM-1140- option | Single axis bipolar stepper motor controller / driver | |
electronics with integrated sensOstep encoder and coolStep feature | 37 x 37 x |
11.5
Table 2.1 Order codes
The following options are available:
Firmware option | Description | Order code example: |
---|---|---|
-TMCL | Module pre-programmed with TMCL firmware | TMCM-1140- TMCL |
-CANopen | Module pre-programmed with CANopen firmware | TMCM-1140- CANopen |
Table 2.2 Firmware options
A cable loom set is available for this module:
Order code | Description |
---|---|
TMCM-1140-CABLE | Cable loom for TMCM-1140: |
• 1x cable for power and communication connector (length 200mm)
– 1x cable for multipurpose In/Out connector (length 200mm)
– 1x cable for motor connector (length 200mm)
– 1x USB type A connector to mini-USB type B connector cable (length 1.5m)
Table 2.3 Cable loom order codes
Please note that the TMCM-1140 is available with NEMA17 stepper motors, too.
Refer to the PD-1140 documents for more information about these products.
Mechanical and Electrical Interfacing
3.1 Dimensions and Mounting Holes
The dimensions of the controller/driver board are approx. 37 mm x 37 mm x 11.5
mm in order to fit on the back of a 42 mm stepper motor. Maximum component
height (height above PCB level) without mating connectors is around 8mm above
PCB level and 2 mm below PCB level. There are two mounting holes for M3 screws
for mounting to a NEMA17 stepper motor.
3.2 Board mounting considerations
The TMCM-1140 offers two metal plated mounting holes. Both mounting holes are
connected to system and signal ground (same as power supply ground).
In order to minimize distortion of signals and radiation of HF signals
(improve EMC compatibility) especially in sensitive / noisy environments it is
important to ensure a solid ground connection within the system. In order to
support this, it is recommended to connect both mounting holes of the board
in addition to the supply ground connection to system power supply ground.
Nevertheless, this might not always be an option e.g. in case the metal system
chassis / TMCM-1140 mounting plate is already connected to earth and a direct
connection between supply ground (secondary side) and mains supply earth
(primary side) is not desired / not an option. In this case plastic (e.g. made
of nylon) spacers / distance bolts and screws should be used.
3.3 Connectors of TMCM-1140
The controller/driver board of the TMCM-1140 offers four connectors including
the motor connector which is used for attaching the motor coils to the
electronics. The power and communication connector is used for power supply,
CAN interface, and RS485 interface. The 8pin multipurpose I/O connector
offers four multipurpose inputs and two general purpose outputs. Further,
there is a connector for the USB interface.
Label | Connector type | Mating connector type |
---|
Power and Communication Connector
|
CI0106P1VK0-LF
CVIlux CI01 series, 6 pins, 2mm pitch
| Connector housing CVIlux: CI01065000-A
Contacts CVIlux: CI01T011PE0-A
or
Connector housing JST: PHR-6 Contacts JST: SPH-002T-P0.5S
Wire: 0.22mm2
Multipurpose I/O Connector| CI0108P1VK0-LF
CVIlux CI01 series, 8 pins, 2mm pitch| Connector housing CVIlux: CI01085000-A
Contacts CVIlux: CI01T011PE0-A
or
Connector housing JST: PHR-8 Contacts JST: SPH-002T-P0.5S
Wire: 0.22mm2
Motor Connector| CI0104P1VK0-LF
CVIlux CI01 series, 4 pins, 2mm pitch
| Connector housing CVIlux: CI01045000-A Contacts CVIlux: CI01T011PE0-A
or
Connector housing JST: PHR-4 Contacts JST: SPH-002T-P0.5S
Wire: 0.22mm2
Mini-USB Connector| Molex 500075-1517
Mini USB Type B vertical receptacle| Any standard mini-USB plug
Table 3.1 Connectors and mating connectors, contacts and applicable wire
3.3.1 Power and Communication Connector
A 6pin CVIlux CI0106P1VK0-LF 2mm pitch single row connector is used for power
supply, RS485 and CAN serial communication. Please note the additional power
supply information in chapter 3.3.1.1.
Note: CAN interface will be de-activated in case USB is connected due to
internal sharing of hardware resources.
| Pin| Label| Direction| Description
---|---|---|---|---
1| GND| Power (GND)| System and signal ground
2| VDD| Power (Supply)| VDD (+9V…+28V)
3| RS485+| Bidirectional| RS485 interface, diff. signal (non-inverting)
4| RS485-| Bidirectional| RS485 interface, diff. signal (inverting)
5| CAN_H| Bidirectional| CAN interface, diff. signal (non-inverting)
6| CAN_L| Bidirectional| CAN interface, diff. signal (inverting)
Table 3.2 Connector for power supply and interfaces
3.3.1.1 Power Supply
For proper operation care has to be taken with regard to power supply concept
and design. Due to space restrictions the TMCM-1140 includes about 40µF/35V of
supply filter capacitors. These are ceramic capacitors which have been
selected for high reliability and long life time. The module includes a 28V
suppressor diode for over-voltage protection.
CAUTION!
| Add external power supply capacitors!
It is recommended to connect an electrolytic capacitor of significant size
(e.g. at least 470µF/35V) to the power supply lines next to the TMCM-1140!
Rule of thumb for size of electrolytic capacitor: c = 1000 μF/ A ×
ISUPPLY
In addition to power stabilization (buffer) and filtering this added capacitor
will also reduce any voltage spikes which might otherwise occur from a
combination of high inductance power supply wires and the ceramic capacitors.
In addition it will limit slew-rate of power supply voltage at the module. The
low ESR of ceramic-only filter capacitors may cause stability problems with
some switching power supplies.
---|---
| Do not connect or disconnect motor during operation!
Motor cable and motor inductivity might lead to voltage spikes when the
motor is disconnected / connected while energized. These voltage spikes might
exceed voltage limits of the driver MOSFETs and might permanently damage them.
Therefore, always disconnect power supply before connecting / disconnecting
the motor.
| Keep the power supply voltage below the upper limit of 28V!
Otherwise the driver electronics will seriously be damaged! Especially,
when the selected operating voltage is near the upper limit a regulated power
supply is highly recommended. Please see also chapter 7, operating values.
| There is no reverse polarity protection!
The module will short any reversed supply voltage due to internal diodes
of the driver transistors.
3.3.1.2 RS485
For remote control and communication with a host system the TMCM-1140 provides
a two wire RS485 bus interface.
For proper operation the following items should be taken into account when
setting up an RS485 network:
-
BUS STRUCTURE:
The network topology should follow a bus structure as closely as possible. That is, the connection between each node and the bus itself should be as short as possible. Basically, it should be short compared to the length of the bus. -
BUS TERMINATION:
Especially for longer busses and/or multiple nodes connected to the bus and/or high communication speeds, the bus should be properly terminated at both ends. The TMCM-1140 does not integrate any termination resistor. Therefore, 120 Ohm termination resistors at both ends of the bus have to be added externally. -
NUMBER OF NODES:
The RS485 electrical interface standard (EIA-485) allows up to 32 nodes to be connected to a single bus. The bus transceivers used on the TMCM-1140 units (hardware V1.2: SN65HVD3082ED, since hardware V1.3: SN65HVD1781D) have a significantly reduced bus load and allow a maximum of 255 units to be connected to a single RS485 bus using TMCL firmware. Please note: usually it cannot be expected to get reliable communication with the maximum number of nodes connected to one bus and maximum supported communication speed at the same time. Instead, a compromise has to be found between bus cable length, communication speed and number of nodes. -
COMMUNICATION SPEED:
The maximum RS485 communication speed supported by the TMCM-1140 hardware V1.2 is 115200 bit/s and 1Mbit/s since hardware V1.3. Factory default is 9600 bit/s. Please see separate TMCM-1140 TMCL firmware manual for information regarding other possible communication speeds below the upper limit in hardware. -
NO FLOATING BUS LINES:
Avoid floating bus lines while neither the host/master nor one of the slaves along the bus line is transmitting data (all bus nodes switched to receive mode). Floating bus lines may lead to communication errors. In order to ensure valid signals on the bus it is recommended to use a resistor network connecting both bus lines to well defined logic levels.
There are actually two options which can be recommended:
Add resistor (Bias) network on one side of the bus, only (120R termination resistor still at both ends):
Or add resistor (Bias) network at both ends of the bus (like Profibus™ termination):
Certain RS485 interface converters available for PCs already include these additional resistors (e.g. USB-2485 with bias network at one end of the bus).
3.3.1.3 CAN
For remote control and communication with a host system the TMCM-1140 provides
a CAN bus interface. Please note that the CAN interface is not available in
case USB is connected. For proper operation the following items should be
taken into account when setting up a CAN network:
-
BUS STRUCTURE:
The network topology should follow a bus structure as closely as possible. That is, the connection between each node and the bus itself should be as short as possible. Basically, it should be short compared to the length of the bus. -
BUS TERMINATION:
Especially for longer busses and/or multiple nodes connected to the bus and/or high communication speeds, the bus should be properly terminated at both ends. The TMCM-1140 does not integrate any termination resistor. Therefore, 120 Ohm termination resistors at both ends of the bus have to be added externally. -
NUMBER OF NODES:
The bus transceiver used on the TMCM-1140 units (TJA1050T) supports at least 110 nodes under optimum conditions. Practically achievable number of nodes per CAN bus highly depend on bus length (longer bus > less nodes) and communication speed (higher speed -> less nodes).
3.3.2 Multipurpose I/O Connector
An 8pin CVIlux CI0108P1VK0-LF 2mm pitch single row connector is available for
all multipurpose inputs and outputs.
| Pin| Label| Direction| Description
---|---|---|---|---
1| GND| Power (GND)| System and signal ground
2| VDD| Power (Supply)| VDD, connected to VDD pin of the power and
communication connector
3| OUT_0| Output| Open-drain output (max. 1A) Integrated freewheeling diode to
VDD
4| OUT_1| Output| +5V supply output (max. 100mA) Can be switched on/off in
software
5
|
IN_0
|
Input
| Dedicated analog input, Input voltage range: 0..+10V
Resolution: 12bit (0..4095)
6
| IN_1, STOP_L, ENC_A| Input| General purpose digital input (+24V compatible)
Alternate function 1: left stop switch input
Alternate function 2: external incremental encoder channel A input
7
| IN_2, STOP_R, ENC_B|
Input
| General purpose digital input (+24V compatible)
Alternate function 1: right stop switch input
Alternate function 2: external incremental encoder channel B input
8| IN_3, HOME, ENC_N| Input| General purpose digital input (+24V compatible)
Alternate function 1: home switch input
Alternate function 2: external incremental encoder index / zero channel input
Table 3.3 Multipurpose I/O connector
Note:
- All inputs have resistor based voltage input dividers with protection diodes. These resistors also ensure a valid GND level when left unconnected.
- For all digital inputs (IN_1, IN_2, IN_3) a 2k2 pull-up resistor to +5V can be activated (default setting with all more recent TMCL firmware versions). Then these inputs have a default (unconnected) logic level of 1 and an external switch to GND can be connected. This might be especially interesting in case these inputs are used as STOP_L / STOP_R and HOME switch inputs (alternate function 1) or as encoder input for an external incremental A/B/N encoder with open-collector outputs (pull-ups are not necessary for encoder with push-pull outputs).
3.3.2.1 Digital Inputs IN_1, IN_2, IN_3
The eight pin connector of the TMCM-1140 provides three multipurpose digital
inputs IN_1, IN_2 and IN_3. All three inputs accept up to +24V (nom.) input
signals and offer the same input circuit with voltage resistor dividers,
limiting
diodes against over- and under-voltage and programmable 2k2 pull-up resistors.
The pull-ups can be switched on or off for all three inputs at once in
software.
With TMCL firmware command SIO 0, 0, 0 will switch-off the pull-ups and
command SIO 0, 0, 1 will switch them on (see separate TMCL firmware manual,
command SIO for more detailed information). The three digital inputs have alternate
functionality depending on configuration in software. The following functions
are available:
Label (pin)| Default function| Alternate function 1|
Alternate function 2
---|---|---|---
IN_1 (6)| General purpose digital input
_TMCL: GIO 1, 0 // get digital value of input IN1| STOP_L – left stop
switch input, connected to processor and TMC429 REF input (supporting
left stop functionality in hardware)
_TMCL: GAP 11, 0 // get digital value of STOPL input
| ENC_A – external incremental encoder input channel A, connected to
processor encoder counter input
IN_2 (7)| General purpose digital input
_TMCL: GIO 2, 0 // get digital value of input IN2| STOP_R – right stop
switch input, connected to processor and TMC429 REF input (supporting right
stop switch functionality in hardware)
_TMCL: GAP 10, 0 // get digital value of STOPR input| ENC_B – external
incremental encoder input channel B, connected to processor encoder counter
input
IN_3 (8)| General purpose digital input
_TMCL: GIO 3, 0 // get digital value of input IN3| HOME – home switch
input, connected to processor
TMCL: GAP 9, 0 // get digital value of HOME input| ENC_N – external
incremental encoder input index / zero channel, connected to processor
interrupt input
Table 3.4 Multipurpose inputs / alternate functions
– All three digital inputs are connected to the on-board processor and can be
used as general purpose digital inputs (default).
– In order to use IN_1 and IN_2 as STOP_L and STOP_R inputs, this function has
to be enabled explicitly in software (factory default: switched off). With
TMCL firmware the stop switch functionality can be enabled using SAP 12, 0, 0
(STOP_R / right limit switch) and SAP 13, 0, 0 (STOP_L / left limit switch).
As the names already indicate: the status of the left limit switch (STOP_L)
will be significant during motor left turns and the status of the right limit
switch during motor right turns (positive direction), only. Reading out input
values using the GAP commands as listed in the table above is possible at any
time. Please see separate TMCL firmware manual for additional information.
– External encoder: an external incremental A/B/N encoder can be connected to
the TMCM-1140 and used in addition or as an alternative to the internal
sensOstep™ encoder. Using TMCL the encoder counter value for this second
encoder can be read out via TMCL command GAP 216, 0 (see separate TMCL
firmware manual for more details). Factory default scaling of the encoder
counter is 1:1 – that is, after one encoder rotation the encoder counter will
be incremented / decremented by the number of encoder ticks (encoder lines x
4). When using an external encoder connect encoder channel A to IN_1, channel
B to IN_2, the N or zero channel to IN_3 (optional), encoder ground to module
supply ground (e.g. Pin 1 of the Multipurpose I/O connector) and the +5V
supply input of the encoder to OUT_1 (all on the Multipurpose I/O connector).
Please note that in order to supply the encoder with +5V the output OUT_1 has
to be activated first using SIO 1, 2, 1 (see also chapter 3.3.2.3).
3.3.2.2 Analog Input IN_0
The eight pin connector of the TMCM-1140 provides one dedicated analog input
IN_0. This dedicated analog input offers a full scale input range of approx.
0… +10 V (0..+10.56V nom.) with a resolution of the internal analog-to digital
converter of the microcontroller of 12bit (0… 4095).
The input is protected against higher voltages up to +24 V using voltage
resistor dividers together with limiting diodes against voltages below 0 V
(GND) and above +3.3 V DC (see figure below). With TMCL firmware the analog
value of this input may be read using command GIO 0, 1. The command will
return the raw value of the 12bit analog-to-digital converter between 0 ..
4095. It is also possible to read the digital value of this input using TMCL
command GIO 0, 0. The trip point (between 0 and 1) will be at approx. +5V
input voltage (half the analog input range).
3.3.2.3 Outputs OUT_0, OUT_1
The eight pin connector of the TMCM-1140 offers two general purpose outputs
OUT_0 and OUT_1. OUT_0 is an open-drain output capable of switching (sinking)
up to 1A. The output of the N-channel MOSFET transistors is connected to a
freewheeling diode for protection against voltage spikes especially from
inductive loads (relais etc.) above supply voltage (see figure below).
OUT_0 should not be connected to any voltage above supply voltage of the
module due to the internal freewheeling diode.
With TMCL firmware OUT_0 can be switched on (OUT_0 pulled low) using command
SIO 0, 2, 1 and off again (OUT_0 floating) using command SIO 0, 2, 0 (this is
also the factory default setting of this output). In case a floating output
is not desired in the application an external resistor to e.g. supply voltage
may be added.
In contrast OUT_1 is able to supply +5V (sourcing 100mA max.) to an external
load. An integrated P-channel MOSFET allows switching on / off this +5V supply
in software (see figure below). This output might be used in order to supply
+5V to an external encoder circuit. Please note that the +5V supply has to be
activated explicitly in software.With TMCL firmware OUT_1 can be
switched on (supply +5V to external circuit) using command SIO 1, 2, 1 and off
(output pulled low via 10k pull-down resistor) using command SIO 1, 2, 0 (this
is also the factory default setting of this output).
3.3.3 Motor Connector
As motor connector a 4pin CVIlux CI0104P1VK0-LF 2mm pitch single row connector
is available. The motor connector is used for connecting the four motor wires
of the two motor coils of the bipolar stepper motor to the electronics.
| Pin| Label| Direction| Description
---|---|---|---|---
1| OB2| Output| Pin 2 of motor coil B
2| OB1| Output| Pin 1 of motor coil B
3| OA2| Output| Pin 2 of motor coil A
4| OA1| Output| Pin 1 of motor coil A
Table 3.5 Motor connector
Example for connecting the QSH4218 NEMA 17 / 42mm stepper motors:
| TMCM-1140| QS4218 Motor|
Motor connector pin| Cable color| Coil| Description
1| Red| B| Motor coil B pin 1
2| Blue| B-| Motor coil B pin 2
---|---|---|---
3| Green| A-| Motor coil A pin 2
4| Black| A| Motor coil A pin 1
3.3.4 Mini-USB Connector
A 5pin mini-USB connector is available on-board for serial communication (as
alternative to the CAN and RS485 interface). This module supports USB 2.0
Full-Speed (12Mbit/s) connections.
CAN interface will be de-activated as soon as USB is connected due to internal
sharing of hardware resources.
| Pin| Label| Direction| Description
---|---|---|---|---
1| VBUS| Power
(supply input)
| +5V supply from host
2| D-| Bidirectional| USB Data –
3| D+| Bidirectional| USB Data +
4| ID| Power (GND)| Connected to signal and system ground
5| GND| Power (GND)| Connected to signal and system ground
Table 3.6 Connector for USB
For remote control and communication with a host system the TMCM-1140 provides
a USB 2.0 full-speed (12Mbit/s) interface (mini-USB connector). As soon as a
USB-Host is connected the module will accept commands via USB.
USB BUS POWERED OPERATION MODE
The TMCM-1140 supports both, USB self powered operation (when an external
power is supplied via the power supply connector) and USB bus powered
operation, (no external power supply via power supply connector).
On-board digital core logic will be powered via USB in case no other supply is
connected (USB bus powered operation). The digital core logic includes the
microcontroller itself and also the EEPROM. The USB bus powered operation
mode has been implemented to enable configuration, parameter settings, read-
outs, firmware updates, etc. by just connecting an USB cable between module
and host PC. No additional cabling or external devices (e.g. power supply) are
required.
Please note that the module might draw current from the USB +5V bus supply
even in USB self powered operation depending on the voltage level of this
supply.
Motor movements are not possible in this mode. Therefore, always connect a
power supply to the Power and Communication Connector for motor movements.
Motor driver current
The on-board stepper motor driver operates current controlled. The driver
current may be programmed in software for motor coil currents up-to 2A RMS
with 32 effective scaling steps in hardware (CS in table below).
Explanation of different columns in table below:
Motor current setting in software (TMCL)
These are the values for TMCL axis parameter 6 (motor run current) and 7
(motor standby current). They are used to set the run / standby current using
the following TMCL commands:
SAP 6, 0,
SAP 7, 0,
Motor current IRMS [A] Resulting motor current based on motor current setting
Motor current setting in software (TMCL)| Current scaling
step (CS)| Motor current I COIL_PEAK [A]| Motor
current I COIL_RMS [A]
---|---|---|---
0..7| 0| 0.092| 0.065
8..15| 1| 0.184| 0.130
16..23| 2| 0.276| 0.195
24..31| 3| 0.368| 0.260
32..39| 4| 0.460| 0.326
40..47| 5| 0.552| 0.391
48..55| 6| 0.645| 0.456
56..63| 7| 0.737| 0.521
64..71| 8| 0.829| 0.586
72..79| 9| 0.921| 0.651
80..87| 10| 1.013| 0.716
88..95| 11| 1.105| 0.781
96..103| 12| 1.197| 0.846
104..111| 13| 1.289| 0.912
112..119| 14| 1.381| 0.977
120..127| 15| 1.473| 1.042
128..135| 16| 1.565| 1.107
136..143| 17| 1.657| 1.172
144..151| 18| 1.749| 1.237
152..159| 19| 1.842| 1.302
160..167| 20| 1.934| 1.367
168..175| 21| 2.026| 1.432
176..183| 22| 2.118| 1.497
184..191| 23| 2.210| 1.563
192..199| 24| 2.302| 1.628
200..207| 25| 2.394| 1.693
208..215| 26| 2.486| 1.758
216..223| 27| 2.578| 1.823
224..231| 28| 2.670| 1.888
232..239| 29| 2.762| 1.953
240..247| 30| 2.854| 2.018
248..255| 31| 2.946| 2.083
In addition to the settings in the table the motor current may be switched off completely (free-wheeling) using axis parameter 204 (see TMCM-1140 firmware manual).
Reset to Factory Defaults
It is possible to reset the TMCM-1140 to factory default settings without establishing a communication link. This might be helpful in case communication parameters of the preferred interface have been set to unknown values or got accidentally lost.For this procedure two pads on the bottom side of the board have to be shortened.
Please perform the following steps:
- Power supply off and USB cable disconnected
- Short two pads as marked in Figure 5.1
- Power up board (power via USB is sufficient for this purpose)
- Wait until the on-board red and green LEDs start flashing fast (this might take a while)
- Power-off board (disconnect USB cable)
- Remove short between pads
- After switching on power-supply / connecting USB cable all permanent settings have been restored to factory defaults
On-Board LEDs
The board offers two LEDs in order to indicate board status. The function of
both LEDs is dependent on the firmware version. With standard TMCL firmware
the green LED should be flashing slowly during operation and the red LED
should be off.
When there is no valid firmware programmed into the board or during firmware
update the red and green LEDs are permanently on.
BEHAVIOR OF LEDS WITH STANDARD TMCL FIRMWARE
Status | Label | Description |
---|---|---|
Heartbeat | Run | This green LED flashes slowly during operation. |
Error | Error | This red LED lights up if an error occurs. |
Operational Ratings
The operational ratings show the intended or the characteristic ranges and
should be used as design values.
In no case shall the maximum values be exceeded!
Symbol | Parameter | Min | Typ | Max | Unit |
---|---|---|---|---|---|
VDD | Power supply voltage for operation | 9 | 12… 24 | 28 | V |
ICOIL_peak | Motor coil current for sine wave peak (chopper regulated, | ||||
adjustable via software) | 0 | 2.8 | A | ||
ICOIL_RMS | Continuous motor current ( RMS ) | 0 | 2.0 | A | |
IDD | Power supply current | << ICOIL | 1.4 * ICOIL | A | |
TENV | Environment temperature at rated current (no forced cooling required) | ||||
-30 | +50 | °C | |||
TENV_1A | Environment temperature at 1A RMS motor current / half max. | ||||
current (no forced cooling required) | -30 | +70 | °C |
Table 7.1 General operational ratings of module
OPERATIONAL RATINGS OF MULTIPURPOSE I/OS
Symbol | Parameter | Min | Typ | Max | Unit |
---|---|---|---|---|---|
VOUT_0 | Voltage at open drain output OUT_0 | 0 | +VDD | V | |
IOUT_0 | Output sink current of open drain output OUT_0 | 1 | A | ||
VOUT_1 | Voltage at output OUT_1 (when switched on) | +5 | V | ||
IOUT_1 | Output source current for OUT_1 | 100 | mA | ||
VIN_1/2/3 | Input voltage for IN_1, IN_2, IN_3 (digital inputs) | 0 | +VDD | V | |
VIN_L 1/2/3 | Low level voltage for IN_1, IN_2 and IN_3 | 0 | 1.1 | V | |
VIN_H 1/2/3 | High level voltage for IN_1, IN_2 and IN_3 | 3.4 | +VDD | V | |
VIN_0 | Measurement range for analog input IN_0 | 0 | +10*) | V |
Table 7.2 Operational ratings of multipurpose I/Os
*) approx. 0…+10.56V at the analog input IN_0 is translated to 0..4095
(12bit ADC, raw values). Above approx.
+10.56V the analog input will saturate but, not being damaged (up-to VDD).
OPERATIONAL RATINGS OF RS485 INTERFACE
Symbol | Parameter | Min | Typ | Max | Unit |
---|---|---|---|---|---|
NRS485 | Number of nodes connected to single RS485 network | 256 | |||
fRS485 | Maximum bit rate supported on RS485 connection | 9600 | 115200 | ||
1000000*) | bit/s |
Table 7.3: Operational ratings of RS485 interface
*) hardware revision V1.2: max. 115200 bit/s, hardware revision V1.3: max.
1Mbit/s
OPERATIONAL RATINGS OF CAN INTERFACE
Symbol | Parameter | Min | Typ | Max | Unit |
---|---|---|---|---|---|
NCAN | Number of nodes connected to single RS485 network | > 110 | |||
fCAN | Maximum bit rate supported on CAN connection | 1000 | 1000 | kbit/s |
Table 7.4 Operational ratings of the CAN interface
Functional Description
The TMCM-1140 is a highly integrated controller/driver module which can be
controlled via several serial interfaces. Communication traffic is kept low
since all time critical operations (e.g. ramp calculations) are performed on
board. The nominal supply voltage of the unit is 24V DC. The module is
designed for both, standalone operation and direct mode. Full remote control
of device with feedback is possible. The firmware of the module can be updated
via any of the serial interfaces.
In Figure 8.1 the main parts of the TMCM-1140 are shown:
– the microprocessor, which runs the TMCL operating system (connected to TMCL
memory),
– the motion controller, which calculates ramps and speed profiles internally
by hardware,
– the power driver with stallGuard2 and its energy efficient coolStep feature,
– the MOSFET driver stage, and
– the sensOstep encoder with resolutions of 10bit (1024 steps) per revolution.
The TMCM-1140 comes with the PC based software development environment TMCL-
IDE for the Trinamic Motion Control Language (TMCM). Using predefined TMCL
high level commands like move to position a rapid and fast development of
motion control applications is guaranteed.
Please refer to the TMCM-1140 Firmware Manual for more information about TMCL
commands.
TMCM-1140 Operational Description
9.1 Calculation: Velocity and Acceleration vs. Microstep and Fullstep
Frequency
The values of the parameters sent to the TMC429 do not have typical motor
values like rotations per second as velocity. But these values can be
calculated from the TMC429 parameters as shown in this section.
PARAMETERS OF TMC429
Signal | Description | Range |
---|---|---|
fCLK | clock-frequency | 16 MHz |
velocity | – | 0… 2047 |
a_max | maximum acceleration | 0… 2047 |
**** pulse_div | divider for the velocity. The higher the value is, the less | |
is the maximum velocity default value = 0 | 0… 13 |
ramp_div
| divider for the acceleration. The higher the value is, the less is the maximum acceleration
default value = 0
| 0… 13
Usrs| microstep-resolution (microsteps per fullstep = 2usrs)| 0… 8
Table 9.1 TMC429 velocity parameters
MICROSTEP FREQUENCY
The microstep frequency of the stepper motor is calculated with
FULLSTEP FREQUENCY
To calculate the fullstep frequency from the microstep frequency, the
microstep frequency must be divided by the number of microsteps per
fullstep.
The change in the pulse rate per time unit (pulse frequency change per second – the acceleration a) is given by
This results in acceleration in fullsteps of:
EXAMPLE
Signal | value |
---|---|
f_CLK | 16 MHz |
velocity | 1000 |
a_max | 1000 |
pulse_div | 1 |
ramp_div | 1 |
usrs | 6 |
CALCULATION OF THE NUMBER OF ROTATIONS
A stepper motor has e.g. 72 flusters per rotation.
Life Support Policy
TRINAMIC Motion Control GmbH & Co. KG does not authorize or warrant any of its
products for use in life support systems, without the specific written consent
of TRINAMIC Motion Control GmbH & Co. KG.
Life support systems are equipment intended to support or sustain life, and
whose failure to perform, when properly used in accordance with instructions
provided, can be reasonably expected to result in personal injury or
death.![TRINAMIC TMCM 1140 Single Axis Stepper Motor Controller Driver Module
- icon13](https://manuals.plus/wp-content/uploads/2023/07/TRINAMIC-TMCM-1140
-Single-Axis-Stepper-Motor-Controller-Driver-Module-icon13.png)
© TRINAMIC Motion Control GmbH & Co. KG 2013 – 2015
Information given in this data sheet is believed to be accurate and reliable.
However neither responsibility is assumed for the consequences of its use nor
for any infringement of patents or other rights of third parties, which may
result from its use.
Specifications are subject to change without notice.
All trademarks used are property of their respective owners.
Revision History
11.1 Document Revision
Version | Date | Author | Description |
---|---|---|---|
0.90 | 2011-DEC-22 | GE | Initial version |
0.91 | 2012-MAY-02 | GE | Updated for TMCM-1140_V11 pcb version |
1.00 | 2012-JUN-12 | SD | First complete version including new chapters about: |
– reset to factory defaults, and
– LEDs
1.01| 2012-JUL-30| SD| Internal circuit of inputs corrected.
1.02| 2013-MAR-26| SD| Names of inputs changed:
AIN_0 IN_0
IN_0 IN_1
IN_1 IN_2
IN_2 IN_3
Names of outputs changed:
OUT_1 = OUT_0
OUT_0 = OUT_1
1.03| 2013-JUL-23| SD| – Connector types updated.
– Chapter 3.3.1.1 updated.
1.04| 2015-JAN-05| GE| – New hardware version V13 added
– Motor driver current settings added (chapter 4)
– Several additions
Table 11.1 Document revision
11.2 Hardware Revision
Version | Date | Description |
---|---|---|
TMCM-1040_V10*) | 2011-MAR-08 | Initial version |
TMCM-1140_V11*) | 2011-JUL-19 | – Optimization of multipurpose I/O circuits |
– Clock generation and distribution changed (16MHz oscillator)
TMCM-1140_V12)| 2012-APR-12| – Further cost optimization incl. different
sensor IC with 10bit max. resolution
TMCM-1140_V13)| 2013-AUG-22| – Stepper motor driver MOSFETs: The MOSFETs of
the driver stage have been replaced. The new MOSFETs offer less heat
dissipation than the previous / currently used ones. Apart from that the
performance and settings including driver output current and output waveform
are essentially the same.
– General purpose outputs OUT_0 / OUT_1: The MOSFETs used for switching these
outputs on / off have been replaced. The new MOSFETs offer less heat
dissipation than the previous / currently used ones. Apart from that the
functionality and ratings are essentially the same.
– RS485 transceiver: the RS485 transceiver has been replaced with the
SN65HVD1781 transceiver offering better fault protection (up-to 70V fault
protection) and supporting higher communication speeds (up-to 1Mbit/s).
– In progress (coming soon): Conformal coating of both sides of the PCB.
Provides improved protection against humidity and dust / swarf (e.g. in case
of the motor mounted versions PD42-x-1140: tiny metal parts on the
Version| Date| Description
---|---|---
| | PCB attracted by the encoder magnet might lead to malfunction of the
unprotected device).
Table 11.2 Hardware revision
*): V10, V11: prototypes only.
**) V12: series product version. Is replaced with V13 series product version
due to EOL (end-of-life) of MOSFETs. Please see
“PCN_1014_08_29_TMCM-1140.pdf” on our Web-site, also
References
[TMCM-1140 TMCL] | TMCM-1140 TMCL Firmware Manual |
---|---|
[TMC262] | TMC262 Datasheet |
[TMC429] | TMC429 Datasheet |
[TMCL-IDE] | TMCL-IDE User Manual |
TRINAMIC Motion Control GmbH & Co. KG
Hamburg, Germany
www.trinamic.com
Please refer to www.trinamic.com.
www.trinamic.com
Downloaded from Arrow.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>