TRINAMIC TMCM-1160 1 Axis Stepper Controller Driver Instruction Manual
- June 10, 2024
- TRINAMIC
Table of Contents
- TRINAMIC TMCM-1160 1 Axis Stepper Controller Driver
- Product Information
- Product Usage Instructions
- Features
- Order Codes
- Mechanical and Electrical Interfacing
- Jumpers
- Reset to Factory Defaults
- On-board LED
- Operational Ratings
- Functional Description
- TMCM-1160 Operational Description
- Life Support Policy
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TRINAMIC TMCM-1160 1 Axis Stepper Controller Driver
Product Information
The Module for Stepper Motors is a hardware device with version V1.1 that serves as a one-axis stepper controller and driver with a 2.8A/48V capacity. It features USB, RS485, and CAN Step/Dir Interfaces, as well as sensOstep TM Encoder. The product is manufactured by TRINAMIC Motion Control GmbH & Co. KG in Hamburg, Germany. The device comes with a hardware manual and unique features such as real-time motion profile calculation, on-the-fly alteration of motor parameters, high-performance microcontroller for overall system control and serial communication protocol handling, bipolar stepper motor driver with up to 256 micro steps per full step, high-efficient operation, low power dissipation, dynamic current control, integrated protection, stallGuard2 feature for stall detection, and cool Step feature for reduced power consumption and heat dissipation.
Product Usage Instructions
- Dimensions and Mounting Holes: The product has specific dimensions and mounting holes that should be considered when installing the device.
- Power Connector: The power connector should be connected to the power supply with the correct voltage to ensure proper functioning of the device.
- Serial Communication Connector: The serial communication connector can be connected to either RS485 or CAN interface for communication purposes.
- Step/Direction Connector: The step/direction connector should be connected to the corresponding inputs for step/direction/enable functions.
- Encoder Connector: The encoder connector should be connected to the encoder inputs for encoder functions.
For optimal usage of the Module for Stepper Motors, it is recommended to refer to the hardware manual provided by the manufacturer. The manual contains detailed information on the mechanical and electrical interfacing of the device, order codes, and other essential information for proper installation and usage of the device.
Features
The TMCM-1160 is a single axis controller/driver module for 2-phase bipolar stepper motors with state of the art feature set. It is highly integrated, offers a convenient handling and can be used in many decentralized applications. The module can be mounted on the back of NEMA 23 (57mm flange size) or NEMA 24 (60mm flange size) stepper motors and has been designed for coil currents up to 2.8 A RMS and 12, 24 or 48 V DC supply voltage. With its high energy efficiency from TRINAMIC’s coolStep™ technology cost for power consumption is kept down. The TMCL™ firmware allows for both, standalone operation and direct mode.
MAIN CHARACTERISTICS
Motion controller
- Motion profile calculation in real-time
- On the fly alteration of motor parameters (e.g. position, velocity, acceleration)
- High performance microcontroller for overall system control and serial communication protocol handling
Bipolar stepper motor driver
- Up to 256 microsteps per full step
- High-efficient operation, low power dissipation
- Dynamic current control
- Integrated protection
- stallGuard2 feature for stall detection
- coolStep feature for reduced power consumption and heat dissipation
Encoder
- sensOstep magnetic encoder (1024 increments per rotation) e.g. for step-loss detection under all operating
- conditions and positioning supervision
- Interface for connection of external incremental a/b/n encoder
Interfaces
- RS485 interface
- CAN (2.0B up to 1Mbit/s) interface
- USB full speed (12Mbit/s) interface
- Step/Direction interface (optically isolated)
- 3 inputs for stop switches and home switch (+24V compatible) with programmable pull-up
- 2 general purpose inputs (+24V compatible) and 2 general purpose outputs (open collector)
- Incremental a/b/n encoder interface (TTL and open-collector signals supported directly)
Safety features
- Shutdown input – driver will be disabled in hardware as long as this pin is left open or shorted to ground
- Separate supply voltage inputs for driver and digital logic – driver supply voltage may be switched off externally while supply for digital logic and therefore digital logic remains active
Software
- TMCL: standalone operation or remote controlled operation, program memory (non volatile) for up to 2048 TMCL commands, and PC-based application development software TMCL-IDE available for free.
- Ready for CANopen
Electrical and mechanical data
- Supply voltage: common supply voltages +12 V DC / +24 V DC / +48 V DC supported (+9 V… +51 V DC)
- Motor current: up to 2.8 A RMS (programmable)
Refer to separate TMCL Firmware Manual, too.
TRINAMICS UNIQUE FEATURES – EASY TO USE WITH TMCL
stallGuard2™
stallGuard2 is a high-precision sensorless load measurement using the back EMF
on the coils. It can be used for stall detection as well as other uses at
loads below those which stall the motor. The stallGuard2 measurement value
changes linearly over a wide range of load, velocity, and current settings. At
maximum motor load, the value goes to zero or near to zero. This is the most
energy-efficient point of operation for the motor.
Figure 1.1 stallGuard2 load measurement SG as a function of load
coolStep™
coolStep is a load-adaptive automatic current scaling based on the load
measurement via stallGuard2 adapting the required current to the load. Energy
consumption can be reduced by as much as 75%. coolStep allows substantial
energy savings, especially for motors which see varying loads or operate at a
high duty cycle. Because a stepper motor application needs to work with a
torque reserve of 30% to 50%, even a constant-load application allows
significant energy savings because coolStep automatically enables torque
reserve when required. Reducing power consumption keeps the system cooler,
increases motor life, and allows reducing cost.
Order Codes
Order code | Description | Size (mm 3) |
---|---|---|
TMCM-1160- option | Single axis bipolar stepper motor controller / driver | |
electronics with integrated sensOstep encoder and coolStep feature | 60 x 60 x |
15
Table 2.1 Order codes
The following options are available:
Firmware option | Description | Order code example |
---|---|---|
-TMCL | Module pre-programmed with TMCL firmware | TMCM-1160- TMCL |
Table 2.2 Firmware options
A cable loom set is available for this module:
Order code | Description |
---|---|
TMCM-1160-CABLE | Cable loom for TMCM-1160: |
- 1x cable loom for power connector (length 200mm)
- 1x cable loom for communication connector (length 200mm)
- 1x cable loom for multi-purpose I/O connector (length 200mm)
- 1x cable loom for S/D connector (length 200mm)
- 1x cable loom for encoder connector (length 200mm)
- 1x cable loom for motor connector (length 200mm)
- 1x USB type A connector to mini-USB type B connector cable (length 1.5m)
Table 2.2 Cable loom order codes
Please note that the TMCM-1160 is available with NEMA23 or NEMA24 stepper motors, too. Refer to the PD-1160 documents for more information about these products.
Mechanical and Electrical Interfacing
Dimensions and Mounting Holes
- The dimensions of the TMCM-1160 controller/driver board are approx. 60 mm x 60 mm in order to fit on the back side of the 60 mm stepper motor.
- Maximum component height above PCB level without mating connectors is around 10.5 mm (jumpers for RS485 / CAN termination included).
- Maximum component height below PCB level is around 4 mm.
- There are four mounting holes for M3 screws for mounting the board either to a NEMA23 (two mounting holes at opposite corners) or a NEMA24 (other two mounting holes at opposite corners) stepper motor.
Connectors of TMCM-1160
The TMCM-1160 offers seven connectors including the motor connector which is
used for attaching the motor coils to the electronics. In addition to the
power connector there are two connectors for serial communication (mini-USB
connector and 5pin connector for RS485 and CAN) and three connectors for
Step/Direction, multipurpose input/output signals, and for an external
encoder.
The multipurpose connector offers two general purpose outputs, two general
purpose inputs, two inputs for stop switches and one for an additional home
switch.
The power supply connector offers separate inputs for driver and for logic
power supply plus hardware shutdown input. Leaving the shutdown input open or
tying it to ground will disable the motor driver stage in hardware. For
operation, this input should be tied to supply voltage.
Label | Connector type | Mating connector type |
---|---|---|
Power Connector | JST B4B-EH-A (JST EH series, 4pins, 2.5mm pitch) | Connector |
housing: JST EHR-4 Contacts: JST SEH-001T-P0.6
Wire: 0.33mm2, AWG 22
Serial communication Connector| JST B5B-PH-K-S (JST PH series, 5pins, 2mm
pitch)| Connector housing: JST PHR-5 Contacts: JST SPH-002T-P0.5S
Wire: 0.22mm2, AWG 24
Multi-purpose I/O Connector| JST B8B-PH-K-S (JST PH series, 8pins, 2mm pitch)|
Connector housing: JST PHR-8 Contacts: JST SPH-002T-P0.5S
Wire: 0.22mm2, AWG 24
Step/Direction Connector| JST B4B-PH-K-S (JST EH series, 4pins, 2mm pitch)|
Connector housing: JST PHR-4 Contacts: JST SPH-002T-P0.5S
Wire: 0.22mm2, AWG 24
Encoder Connector| JST B5B-PH-K-S (JST EH series, 5pins, 2mm pitch)| Connector
housing: JST PHR-5 Contacts: JST SPH-002T-P0.5S
Wire: 0.22mm2, AWG 24
Motor Connector| JST B4B-EH-A (JST PH series, 4pins, 2.5mm pitch)| Connector
housing: JST EHR-4 Contacts: JST SEH-001T-P0.6
Wire: 0.33mm2, AWG 22
Mini-USB
Connector
| Molex 500075-1517
Mini USB Type B vertical receptacle| Any standard mini-USB plug
Power Connector
This module offers separate power supply inputs for digital logic (pin 2) and
driver/power stage (pin 1). Both supply inputs use common ground connections
(pin 4). This way, power supply for the driver stage may be switched off while
still maintaining position and status information when keeping digital logic
supply active. Due to internal diode the digital logic supply has to be equal
or higher than the driver/power stage supply. Otherwise the diode between
driver/power stage supply and digital logic supply might short the separate
supplies.
+UDRIVER SUPPLY ONLY
In case power supply is provided only to the power section (pin 1) an internal
diode will distribute power to the logic section. So, when separate power
supplies are not required it is possible to just use pin 1 and 4 for powering
the module. If so, pin 2 (logic supply) and pin 3 (/SHUTDOWN input) can be
connected together in order to enable the driver stage.
ENABLING THE DRIVER STAGE
Connect /SHUTDOWN input to +UDriver or +ULogic in order to activate the driver
stage. Leaving this input open or connecting it to ground will disable driver
stage.
A 4-pin JST EH series B4B-EH connector is used as power connector on-board.
| Pin| Label| Description
---|---|---|---
| 1| +VDriver| Module + driver stage power supply input
2| +VLogic| (Optional) separate digital logic power supply input
| 3| SHUTDOWN| Shutdown input. Connect this input to +VDriver or +VLogic in
order to activate driver stage. Leaving this input open or connecting it to
ground
| | | will disable driver stage
| 4| GND| Module ground (power supply and signal ground)
Table 3.2 Connector for power supply
Power Supply
For proper operation care has to be taken with regard to the power supply
concept and design. Due to space restrictions the TMCM-1160 includes about 20
µF / 100 V of supply filter capacitors. These are ceramic capacitors which
have been selected for high reliability and long life time.
HINTS FOR POWER SUPPLY CABLES
- Keep power supply cables as short as possible.
- Use large diameters for power supply cables.
CAUTION!
**| Add external power supply capacitors!**
It is recommended to connect an electrolytic capacitor of significant size
(e.g. 2200 µF / 63 V) to the power supply lines next to the TMCM-1160
especially if the distance to the power supply is large (i.e. more than 2-3m)!
Rule of thumb for size of electrolytic capacitor: c = 1000 × IMOT
A In addition to power stabilization (buffer) and filtering this added capacitor will also reduce any voltage spikes which might otherwise occur from a combination of high inductance power supply wires and the ceramic capacitors. In addition it will limit slew-rate of power supply voltage at the module. The low ESR of ceramic-only filter capacitors may cause stability problems with some switching power supplies.
---|---
**| Do not connect or disconnect motor during operation!
Motor cable and motor inductivity might lead to voltage spikes when the
motor is disconnected / connected while energized. These voltage spikes might
exceed voltage limits of the driver MOSFETs
**| and might permanently damage them. Therefore, always disconnect power
supply before connecting / disconnecting the motor .
**| Keep the power supply voltage below the upper limit of 51V!
Otherwise the driver electronics will seriously be damaged! Especially,
when the selected operating voltage is near the upper limit a regulated power
supply is highly recommended. Please see also chapter Fehler! Verweisquelle
konnte nicht gefunden werden.Fehler! Verweisquelle konnte nicht gefunden
werden. (operating values) .
**| There is no reverse polarity protection!
The module will short any reversed supply voltage due to internal diodes
of the driver transistors.
Serial Communication Connector
The module supports RS485 and CAN communication via this connector.
CAN interface will be de-activated in case USB is connected due to internal sharing of hardware resources.
A 2mm pitch 5-pin JST B5B-PH-K connector is used for serial communication.
| Pin| Label| Description
---|---|---|---
1| CAN_H| CAN bus signal (dominant high)
2| CAN_L| CAN bus signal (dominant low)
3| GND| Module ground (system and signal ground)
4| RS485+| RS485 bus signal (non inverted)
5| RS485-| RS485 bus signal (inverted)
Table 3.3 Connector for serial communication
RS485
For remote control and communication with a host system the TMCM-1160 provides
a two wire RS485 bus interface. For proper operation the following items
should be taken into account when setting up an RS485 network:
-
BUS STRUCTURE:
The network topology should follow a bus structure as closely as possible. That is, the connection between each node and the bus itself should be as short as possible. Basically, it should be short compared to the length of the bus.
Figure 6.4 Bus structure -
BUS TERMINATION:
Especially for longer busses and/or multiple nodes connected to the bus and/or high communication speeds, the bus should be properly terminated at both ends. The TMCM-1160 does offer on-board termination resistors which can be activated with the help of a jumper. The jumper has to be removed for units not connected to one end of the bus! -
NUMBER OF NODES:
The RS485 electrical interface standard (EIA-485) allows up to 32 nodes to be connected to a single bus. The bus transceiver used on the TMCM-1160 units (SN65HVD485ED) has 1/2 of the standard bus load and allows a maximum of 64 units to be connected to a single RS485 bus. -
NO FLOATING BUS LINES:
Avoid floating bus lines while neither the host/master nor one of the slaves along the bus line is transmitting data (all bus nodes switched to receive mode). Floating bus lines may lead to communication errors. In order to ensure valid signals on the bus it is recommended to use a resistor network connecting both bus lines to well defined logic levels. In contrast to the termination resistors this network is normally required just once per bus. Certain RS485 interface converters available for PCs already include these additional resistors (e.g. USB-2-485).
CAN
For remote control and communication with a host system the TMCM-1160 provides a CAN bus interface. Please note that the CAN interface is not available in case USB is connected. For proper operation the following items should be taken into account when setting up a CAN network: -
BUS STRUCTURE:
The network topology should follow a bus structure as closely as possible. That is, the connection between each node and the bus itself should be as short as possible. Basically, it should be short compared to the length of the bus.
Figure 3.6 CAN bus structure -
BUS TERMINATION:
Especially for longer busses and/or multiple nodes connected to the bus and/or high communication speeds, the bus should be properly terminated at both ends. The TMCM-1160 does offer on-board termination resistors which can be activated with the help of a jumper (see chapter 7). The jumper has to be removed for units not connected to one end of the bus! -
NUMBER OF NODES:
The bus transceiver used on the TMCM-1160 units (TJA1050T or similar) supports at least 110 nodes under optimum conditions. Practically achievable number of nodes per CAN bus highly depends on bus length (longer bus -> less nodes) and communication speed (higher speed -> less nodes).
Multipurpose I/O Connector
A 2mm pitch 8-pin JST B8B-PH-K connector is used for connecting general
purpose inputs, home and stop switches and outputs to the unit:
| Pin| Label| Description
---|---|---|---
1| OUT_0| General purpose output, open drain (max. 1A) Integrated freewheeling
diode connected to +VLogic
2| OUT_1| General purpose output, open drain (max. 1A) Integrated freewheeling
diode connected to +VLogic
3| IN_0| General purpose input (analog and digital), +24V compatible
Resolution when used as analog input: 12bit (0..4095)
4| IN_1| General purpose input (analog and digital), +24V compatible
Resolution when used as analog input: 12bit (0..4095)
5| STOP_L| Left stop switch input (digital input), +24V compatible,
programmable
internal pull-up to +5V
6| STOP_R| Right stop switch input (digital input), +24V compatible,
programmable internal pull-up to +5V
7| HOME| Home switch input (digital input), +24V compatible, programmable
internal pull-up to +5V
8| GND| Module ground (system and signal ground)
Table 3.4 Multipurpose I/O connector
All inputs have resistor based voltage dividers with protection diodes. These resistors also ensure a valid GND level
For reference switch inputs (STOP_L, STOP_R, HOME) a 1k pull-up resistor to +5V can be activated (separately for each input). Then these inputs have a default (unconnected) logic level of “1” and an external switch to GND can be connected.
Digital Inputs STOP_L, STOP_R, and HOME
The eight pin connector of the TMCM-1160 provides three reference switch
digital inputs STOP_L, STOP_R and HOME. All three inputs accept up to +24 V
input signals. They are protected against these higher voltages using voltage
resistor dividers together with limiting diodes against voltages below 0 V
(GND) and above +3.3 V DC.
Figure 3.6 STOP_L, STOP_R and HOME inputs (simplified input circuit)
All three digital inputs are connected to the on-board processor and can be used as general purpose digital inputs!
General Purpose Inputs IN_0 and IN_1
The eight pin connector of the TMCM-1160 provides two general purpose
inputs which may be used as either digital or analog inputs.
GENERAL PURPOSE INPUTS AS ANALOG INPUTS
As analog input they offer a full scale input range of 0… +10 V with a
resolution of the internal analog-to-digital converter of the microcontroller
of 12bit (0… 4095). The input is protected against higher voltages up to +24 V
using voltage resistor dividers together with limiting diodes against voltages
below 0 V (GND) and above +3.3 V DC.
Figure 3.7 General purpose inputs (simplified input circuit)
Outputs OUT_0, OUT_1
The eight pin connector of the TMCM-1160 offers two general purpose outputs
OUT_0 and OUT_1. These two outputs are open-drain outputs and can sink up to 1
A each. The outputs of the N-channel MOSFET transistors are connected to
freewheeling diodes each for protection against voltage spikes especially from
inductive loads (relays etc.) above supply voltage.
- In case free-wheeling diodes are connected to VDD supply voltage: none of the two outputs should be connected to any voltage above supply voltage of the module.
- It is recommended to connect +Vlogic of the power connector to the power supply output in case the outputs OUT_0/1 are used to switch inductive loads (e.g. relays etc.).
Figure 3.8 General purpose outputs
Step/Direction Connector
A 2mm pitch 4-pin JST B4B-PH-K connector is used for step and direction input
signals. This is an option in case the on-board controller is used for
configuration of the driver stage, only. The Step/Direction input is optically
isolated and will allow direct control of the driver stage.
Please do not attach any signal to this input if the on-board motion controller is used! Otherwise step or direction signal connected here might interfere with signals generated on-board.
| Pin| Label| Description
---|---|---|---
1| COM| Common supply for the opto-coupler inputs (+5V… +24V)
2| ENABLE| Enable signal input (function depends on firmware)
STEP| Step signal input (connected to step input of TMC262 driver IC)
4| DIRECTIO| Direction signal (connected to direction input of TMC262
driver IC)
Table 3.4 Connector for step/direction signals
Step / Direction / Enable Inputs
The inputs Step, Direction and Enable are electrically (optically) isolated
from the power supply and all other signals of the TMCM-1160 module. These
inputs have one common reference input COMMON.
The COMMON input should be connected to a positive supply voltage between +5 V
and +24 V. Step / Direction / Enable signals might be driven either by open-
collector / open-drain outputs or by push-pull outputs.
In case of push-pull outputs the COMMON supply voltage should be equal /
similar to the high signal voltage level of the push-pull drivers.
Figure 3.9 Step / Direction / Enable inputs
Encoder Connector
The module supports an external incremental a/b/n encoder via this connector.
The external encoder may be used in addition or as an alternative to the
internal / on-board sensOstep encoder.
A 2mm pitch 5-pin JST B5B-PH-K connector is used for connecting an external
encoder with TTL (+5 V push-pull) or open-collector signals directly:
| Pin| Label| Description
---|---|---|---
1| GND| Module ground (system and signal ground)
2| +5V| +5V supply output for external encoder circuit (100 mA max.)
3| ENC_A| Encoder a channel input (internal pull-up)
4| ENC_B| Encoder b channel input (internal pull-up)
5| ENC_N| Optional encoder n / index channel input (internal pull-up)
Table 3.5 Connector for an external incremental encoder
Encoder Inputs
The TMCM-1160 offers a dedicated encoder input for incremental a/b encoders
with optional n / index-channel.
Encoders with +5 V push-pull (TTL) signals or open-collector signals (on-board
pull-ups) might be connected directly. This connector offers a +5 V supply
output for supply of the encoder circuit. Up to 100mA might be drawn from this
output.
Connecting an external encoder is an option. An external encoder might be used
in addition or as alternative to the internal sensOstep encoder.
Figure 3.9 Encoder a/b/n inputs
Motor Connector
Both motor coil windings (bipolar stepper motor) are connected to the motor
connector.
| Pin| Label| Description
---|---|---|---
1| OA1| Motor coil A
2| OA2| Motor coil A
3| OB1| Motor coil B
4| OB2| Motor coil B
Figure 3.3 Motor connector
TMCM- 1160 | Q5718 motor |
---|---|
Motor connector pin | Cable colour |
1 | Black |
2 | Green |
3 | Red |
4 | Blue |
Mini-USB Connector
A 5-pin standard mini-USB connector is available on board. This module
supports USB 2.0 full-speed (12Mbit/s) connections.
Please note:
- On-board digital core logic (mainly processor and EEPROM) will be powered via USB in case no other supply is connected. The USB connection might be used to set parameters / download TMCL programs or perform firmware updates while power supply for the module (and the rest of the machine) has been switched off or is not connected.
- CAN interface will be de-activated as soon as USB is connected due to internal sharing of hardware resources.
| Pin| Label| Description
---|---|---|---
1| VBUS| +5V supply from host
2| D-| Data –
3| D+| Data +
4| ID| Not connected
5| GND| Module ground (system and signal ground)
Table 3.6 Mini USB connector
For remote control and communication with a host system the TMCM-1160 provides
a USB 2.0 full-speed (12Mbit/s) interface (mini-USB connector). As soon as a
USB-Host is connected the module will accept commands via USB.
USB BUS POWERED OPERATION MODE
The TMCM-1160 supports both, USB self powered operation (when an external
power is supplied via the power supply connector) and USB bus powered
operation, (no external power supply via power supply connector).
On-board digital core logic will be powered via USB in case no other supply is
connected (USB bus powered operation). The digital core logic comprehends the
microcontroller itself and also the EEPROM. The USB bus powered operation mode
has been implemented to enable configuration, parameter settings, read-outs,
firmware updates, etc. by just connecting an USB cable between module and host
PC. No additional cabling or external devices (e.g. power supply) are
required.
Please note that the module might draw current from the USB +5 V bus supply
even in USB self powered operation depending on the voltage level of this
supply.
Motor movements are not possible in this operation mode. Therefore, connect the power connector and change to USB self powered operation mode.
Jumpers
Most settings of the board are done through the software. Nevertheless, two jumpers are available for configuration.
Figure 4.1 RS485 and CAN bus termination
RS485 Bus Termination
The board includes a 120 Ohm resistor for proper bus termination of the RS485
interface. When this jumper is closed, the resistor will be placed between the
two differential bus lines RS485+ and RS485-.
CAN Bus Termination
The board includes a 120 Ohm resistor for proper bus termination of the CAN
interface. When this jumper is closed, the resistor will be placed between the
two differential bus lines CAN_H and CAN_L.
Reset to Factory Defaults
It is possible to reset the PD-1160 to factory default settings without
establishing a communication link. This might be helpful in case communication
parameters of the preferred interface have been set to unknown values or got
accidentally lost.
For this procedure two pads on the bottom side of the board have to be
shortened (see Figure 5.1).
Figure 5.1 Reset to factory default settings
PERFORM THE FOLLOWING STEPS:
- Power supply off and USB cable disconnected
- Short two pads as marked in Figure 5.1
- Power up board (power via USB is sufficient for this purpose)
- Wait until the on-board red and green LEDs start flashing fast (this might take a while)
- Power-off board (disconnect USB cable)
- Remove short between pads
- After switching on power-supply / connecting USB cable all permanent settings have been restored to factory defaults
On-board LED
The board offers two LEDs in order to indicate board status. The function of
both LEDs is dependent on the firmware version. With standard TMCL firmware
the green LED should be flashing during operation and the red LED should be
off.
When there is no valid firmware programmed into the board or during firmware
update the red and green LEDs are permanently on.
Figure 6.1 On-board LEDs
BEHAVIOR OF LEDS WITH STANDARD TMCL FIRMWARE
Status | Label | Description |
---|---|---|
Heartbeat | Run | The green LED flashes during operation. |
Error | Error | The red LED lights up if an error occurs. |
Operational Ratings
The operational ratings show the intended or the characteristic ranges and should be used as design values. In no case shall the maximum values be exceeded!
GENERAL OPERATIONAL RATINGS OF THE MODULE
Symbol | Parameter | Min | Typ | Max | Unit |
---|---|---|---|---|---|
+VDriver / +VLogic | Power supply voltage for operation | 9 | 12, 24, 48 | 51 | V |
DC )
IUSB| USB supply current when USB bus powered (+5V USB supply)| | 70| | mA
ICOIL_peak| Motor coil current for sine wave peak (chopper regulated,
adjustable via software)| 0| | 4| A
ICOIL_RMS| Continuous motor current (RMS)| 0| | 2.8| A
ISUPPLY| Power supply current| | << ICOIL| 1.4 ICOIL| A
TENV| Environment temperature at +48V supply and rated current (100% duty-
cycle, no forced cooling required)| | | 40| °C
TENV| Environment temperature at +24V supply and rated current (100% duty-
cycle, no forced cooling
required)
| | | 50| °C
Table 7.1 General operational ratings of module
- Attention: due to the internal diode between VDriver and VLogic VLogic should be always equal or higher than VDriver.
GENERAL OPERATIONAL RATINGS OF STEP/DIRECTION INPUT
Symbol | Parameter | Min | Type | Max | Unit |
---|---|---|---|---|---|
VCOMMON | Supply voltage for common supply input for step, direction and enable | ||||
(inputs have negative logic) | 5… 24 | 27 | V |
VSTEP/DIR/ENABLE_O
N
| Signal voltage at step, direction and enable input (active, opto-coupler
on)| 3.5| 4.5… 24| 30| V
VSTEP/DIR/ENABLE_OF
F
| Signal voltage at step, direction and enable input (inactive, opto-coupler
off)| -5.5| 0| 2| V
VSTEP/DIR/ENABLE_O
N
| Opto-coupler current when switched on (internally
regulated)| | 6… 8| | mA
fSTEP| Step frequency| | | 1 *)| MHz
Table 7.2 Operational ratings of Step/Direction input
- Maximum frequency for +5 V TTL level step signals is with 50 % duty cycle.
OPERATIONAL RATINGS OF THE GENERAL PURPOSE INPUTS/OUTPUTS
Symbol | Parameter | Min | Type | Max | Unit |
---|---|---|---|---|---|
VSTOP_L/R/HOME | Input voltage for STOP_L/R/HOME | 0 | 24 | V | |
VSTOP_L/R/HOME_L | Low level voltage for STOP_L/R/HOME | 0 | 1.3 | V | |
VSTOPL/R/HOME_H | High level voltage for STOP_L/R/HOME (internal programmable | ||||
1k pull-up to +5V) | 3 | 24 | V | ||
VIN_0/1_digital | Input voltage for IN_0 and IN_1 when used as digital input | ||||
0 | 24 | V | |||
VIN_0/1_analog | Full range input voltage for IN_0 and IN_1 when used as analog | ||||
input | 0 | 10 | V | ||
VIN_0/1_L | Low level voltage for IN_0 and IN_1 when used as digital input | ||||
(internal 10k pull-down) | 0 | 1.3 *) | V | ||
VIN_0/1_H | High level voltage for IN_0 and IN_1 when used |
as digital input
| 3 *)| | 24| V
VOUT_0/1| Voltage at open collector output| 0| | VLOGIC +
0.5 **)
| V
IOUT_0/1| Output sink current at open collector outputs| | | 1| A
Table 7.3 Operational ratings of the general purpose inputs/outputs
- this voltage is programmable (internal 12bit ADC)
- limited to module supply voltage + 0.5V due to integrated freewheeling diode between general purpose output and module supply voltage
Functional Description
The TMCM-1160 is a highly integrated controller/driver module which can be
controlled via several serial interfaces. Communication traffic is kept low
since all time critical operations (e.g. ramp calculations) are performed on
board. Common supply voltages are +12VDC / +24VDC / +48VDC. The module is
designed for both, standalone operation and direct mode. Full remote control
of device with feedback is possible. The firmware of the module can be updated
via any of the serial interfaces.
In Figure 8.1 the main parts of the TMCM-1160 are shown:
- the microprocessor, which runs the TMCL operating system (connected to TMCL memory),
- the motion controller, which calculates ramps and speed profiles internally by hardware,
- the power driver with stallGuard2 and its energy efficient coolStep feature,
- the MOSFET driver stage, and
- the sensOstep encoder with resolutions of 10bit (1024 steps) per revolution.
Figure 8.1 Main parts of the TMCM-1160
The TMCM-1160 comes with the PC based software development environment TMCL-
IDE for the Trinamic Motion Control Language (TMCM). Using predefined TMCL
high level commands like move to position a rapid and fast development of
motion control applications is guaranteed.
Please refer to the TMCM-1160 Firmware Manual for more information about TMCL
commands.
TMCM-1160 Operational Description
Calculation: Velocity and Acceleration vs. Microstep and Fullstep
Frequency
The values of the parameters sent to the TMC429 do not have typical motor
values like rotations per second as velocity. But these values can be
calculated from the TMC429 parameters as shown in this section.
PARAMETERS OF TMC429
Signal | Description | Range |
---|---|---|
fCLK | clock-frequency | 16 MHz |
velocity | – | 0… 2047 |
a_max | maximum acceleration | 0… 2047 |
pulse_div | divider for the velocity. The higher the value is, the less is the | |
maximum velocity default value = 0 | 0… 13 | |
ramp_div | divider for the acceleration. The higher the value is, the less is | |
the maximum acceleration default value = 0 | 0… 13 | |
Usrs | microstep-resolution (microsteps per fullstep = 2usrs) | 0… 8 |
Table 9.1 TMC429 velocity parameters
MICROSTEP FREQUENCY
The microstep frequency of the stepper motor is calculated with
FULLSTEP FREQUENCY
To calculate the full step frequency from the microstep frequency, the
microstep frequency must be divided by the number of microsteps per full step.
The change in the pulse rate per time unit (pulse frequency change per second – the acceleration a) is given by
This results in acceleration in full steps of:
EXAMPLE:
Signal | value |
---|---|
f_CLK | 16 MHz |
velocity | 1000 |
a_max | 1000 |
pulse_div | 1 |
ramp_div | 1 |
usrs | 6 |
CALCULATION OF THE NUMBER OF ROTATIONS
A stepper motor has e.g. 72 full steps per rotation.
Life Support Policy
TRINAMIC Motion Control GmbH & Co. KG does not authorize or warrant any of its
products for use in life support systems, without the specific written consent
of TRINAMIC Motion Control GmbH & Co. KG.
Life support systems are equipment intended to support or sustain life, and
whose failure to perform, when properly used in accordance with instructions
provided, can be reasonably expected to result in personal injury or death.
© TRINAMIC Motion Control GmbH & Co. KG 2013
Information given in this data sheet is believed to be accurate and reliable.
However neither responsibility is assumed for the consequences of its use nor
for any infringement of patents or other rights of third parties, which may
result from its use.
Specifications are subject to change without notice.
Revision History
Document Revision
Version| Date| Author
GE – Göran Eggers SD – Sonja Dwersteg| Description
---|---|---|---
0.91| 2012-MAY-03| GE| Initial version
1.00
| ****
2012-JUN-13
| ****
SD
| First complete version including the following chapters:
- Reset to factory defaults,
- LEDs
1.01| 2012-JUL-27| SD| Figure 3.6 (general purpose inputs) corrected.
1.02| 2013-JUL-08| SD| Chapter 3.2.1.1 updated
Table 11.1 Document revision
Hardware Revision
Version | Date | Description |
---|---|---|
TMCM-1160_V10 | 2011-JUL-20 | Initial version |
TMCM-1160_V11 | 2012-JAN-24 | Inputs IN_0 and IN_1 can be used as analog inputs, |
also
Table 11.2 Hardware revision
References
- [TMCM-1160 TMCL] TMCM-1160 TMCL Firmware Manual
- [TMC262] TMC262 Datasheet
- [TMC429] TMC429 Datasheet
- [TMCL-IDE] TMCL-IDE User Manual
- [QSH5718] QSH5718 Manual
- [QSH6018] QSH6018 Manual
Please refer to www.trinamic.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>