XGIMI Elfin Flip Stand Equipped Projectors User Guide

XGIMI Elfin Flip Stand Equipped Projectors

Scan the QR code for other languages

XGIMI Technology Co., Ltd.
Building A4, No. 1129 Century City Road, New and High-tech Zones, Chengdu City, China
service@xgimi.com www.xgimi.com

Please read the user guide carefully before using this product.
Thank you for buying and using XGIMI products. You should read this user guide carefully before using the product for both your safety and interest.
XGIMI assumes no responsibility for any personal injury, damage to property or other loss caused due to failure to operate this product according to the instructions or precautions in this user guide.

About this user guide
The copyright of this user guide belongs to XGIMI.
The trademarks and names mentioned in this user guide belong to their respective owners.
The content in the user guide may differ from the product.

Any objections to any content or clause found within the Instructions should be reported to XGIMI Technology in written form within 7 days after the purchase otherwise, it will be assumed that you agree to, understand, and accept all the content of the Instructions.

OVERVIEW

Remote

Ports

Projector Status

• Screen Off: Only switch off the display. Other parts are still working.
• Sleep : The projector will reboot quickly next time.
• Restart : Restart the projector completely.
• Shutdown : Switch off the projector completely.

Device on/off

First startup:

1. Connect the power supply and rotate the body to reveal the power button.
2. Press the power button to turn on the projector.
3. Rotate the body to a suitable angle and enter viewing mode.

Sleep:

• a Press the power button on the remote control for the projector to enter sleep mode.
• b Press the power button on the projector body for the projector to enter sleep mode.

Shutdown:

• a Long-press the power button on the remote control, select ‘Shutdown’ from the on-screen menu, and the projector will power off.
• b Press the power button on the projector body for 5 seconds to turn off the power.

Sleep to quick startup:
When the projector is asleep, it can be quickly started in the following ways.Rotate the body to a suitable angle for viewing:

• a Press the power button on the projector to turn on the projector.
• b Press the power button on the remote control to turn on the projector.

Remote Control Pairing
Position the remote control within 10cm of the device, long-press simultaneously. An indicator light will begin flashing as the remote control enters pairing mode. Release the buttons when the flashing begins. After hearing a” ding” sound, the connection is successful.
If pairing fails, wait for 30 seconds and repeat the steps above.

Functions of the Remote Control

Focus adjustment
Use the focus button on the remote control for focusing.
Short-press for auto-focus.
Long-press for manual focus, adjust manually using the left and right buttons on the D-pad.

System Upgrade

Online upgrade
Online upgrades can be performed through the system settings.
You can access system settings by pressing the button.

Important Precautions

• Do not stare directly into the projector lens or have it facing you as the light may be harmful to your eyes.
• Do not block the device’s air inlet/outlet to prevent heat dissipation issues and damage to the internal electronic components.
• Do not wipe the lens with cleaning paper, cloth, or other materials as doing so may damage the lens. Please use an air blower to remove dust from the lens instead.
• Do not wash the device with cleaning chemicals, detergents, or any other liquid to prevent the circuit board from corroding. Avoid exposing the device to rainwater, moisture, and mineral-ccntaining liquids.
• Keep the device, its components and accessories, out of the reach of children.
• Make sure that the device is used in a dry and ventilated environment.
• Do not store the device in extremely hot or cold temperatures as doing so will shorten the life of the device. Place and use the device in an environment of 0°C-40°C.
• Do not put the device into any heating equipment (such as a dryer or microwave oven) for drying.
• Do not squeeze the device or place any obstructions above or behind it to avoid damaging the device and blocking the light path.
• Do not throw, strike, or sharply vibrate the device to prevent damaging the internal circuit board.
• Do not try to disassemble and assemble the device yourself. If any issue occurs, please ccntact the after-sales service of XGIMI.
• Do not repair any product on your own. If the device or any component does not work properly, ccnsult the after-sales service of XGIMI in a timely manner or return the defective product to XGIMI for repair.
• Due to different HDMI specifications, some HDMI cables and devices may not be compatible with the product. Using uncertified HDMI cables may cause display or connection failures. Please use HDMI cables with good radiation shielding.
• Please sleep or turn off the device before closing the body and frame.
• As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5,2015

FCC Warning

This device complies with Part 15 of the FCC rules. Operation is subjected to the following two ccnditions.
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radiofTV technician for help.

ISED Warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions,
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-003(B)/NMB-003(B)
WARNING Please refer the information on exterior bottom enclosures for electrical and safety information before installing or operating the apparatus.

CAUTION

• Risk of fire or explosion if the battery is replaced by an incorrect type.
• Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types):
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion:
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

Wireless Specification

• Bluetooth transmitter frequency range, 2402 MHz -2480 MHz
• Bluetooth transmitter power, < 10 dBm (EIRP)
• Wi-Fi network, IEEE 802.11 a/b/g/n/ac (2.4GHz/5GHz)
• 2.4G Wi-Fi transmitter frequency range,2412 – 2472 MHz
• 2.4G Wi-Fi transmitter power, < 20 dBm (EIRP)
• 5G Wi-Fi transmitter frequency range,5.15-5.35GHz,5.470-5.725GHz,5.725-5.850GHz
• 5G Wi-Fi transmitter power, 5.15-5.25GHz< 23dBm(EIRP),5.25-5.35GHz< 20dBm (EIRP) 5.470-5.725GHz< 20dBm (EIRP),5.725-5.825GHz< 13.98dBm (EIRP)
  Note : This power is for EU only.

CE Maintenance

1. This product shall only be connected to a USB interface of version USB2.0 (5VDC, 0.5A) .

2. Adapter shall be installed near the equipment and shall be easily accessible.

3. Adapter,
   The plug considered as disconnect device of adapter.
   Power supply and ADP (rating),
   Input, AC 100 V-240V, 50/60 Hz, 1.5A
   Output, DC 19.0V, 3.42A

4. The device complies with RF specifications when it is used at a distance of 20 cm away from your body.

5. To prevent possible damage to hearing, do not listen at high volume levels for long periods.

Declaration of Conformity
XGIMI Technology Co., Ltd. hereby declares that the radio equipment type WK03C is in compliance with Directive 2014/53/EU.

This product is allowed to be used in some of EU member states.
For example, the device can be used in the following Member States,
Operations in the 5.15-5.35 GHz band are restricted to indoor usage only.
This Frequency applies to the following Member States or the geographical area within a Member State where restrictions on putting into service or requirements for authorization of use exist.

Radiation Exposure Statement
For remote control, this device complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment.
The transmitter must not be placed or operated in conjunction with any other antenna or transmitter.
For the LED projector, the device meets FCC and IC radiation exposure limits specified for uncontrolled environments. In the installation and operation of the device, the distance between the transmitter and a human body should be at least 20 cm.

Notes:
The 5.150-5.250 GHz frequency range is only for indoor use.
This frequency applies to member states or geographical areas within member states where restrictions on use or authorization requirements exist.

Disposal instructions for used products

1. Only use attachments and accessories specified or provided by the manufacturer (such as the dedicated power supply adapter).
2. This product may emit harmful light radiation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>