caple FGC620 Wall Chimney Hood Instruction Manual

: June 12, 2024
: caple

Table of Contents

caple FGC620 Wall Chimney Hood
Product Information
INTRODUCTION
SAFETY INSTRUCTIONS
WARRANTY
DECLARATIONS OF CONFORMITY
INSTALLATION
OPERATION
CARE AND MAINTENANCE
TROUBLESHOOTING
PRODUCT DIMENSIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

caple FGC620 Wall Chimney Hood

caple-FGC620-Wall-Chimney-Hood-PRODUCT

Product Information

The Wall Chimney Hood is a kitchen appliance designed for home use. It is not suitable for barbecuing, restaurants, or other commercial purposes. The hood and its filter should be cleaned regularly to maintain optimal performance and reduce the risk of fire. This appliance is intended to be used in household and similar applications.

Safety Instructions

Never let children operate the machine.
Clean the cooker hood according to the instruction manual to reduce the risk of fire.
When using a gas hob, do not leave naked flames under the extractor.
Before connecting this appliance, check that the power supply cord is not damaged.
If the room where the hood is to be used contains a fuel-burning appliance such as a central heating boiler, ensure that its flue is of the sealed or balanced flue type. If other types of flue or appliances are fitted, make sure there is adequate air supply to the room.
The air must not be discharged into a flue used for exhausting fumes from appliances burning gas or other fuels.
To ensure the best performance, we recommend using the appliance in accordance with the regulations concerning the discharge of air.
Never immerse the appliance in water.
If the power cable is damaged, it must only be replaced by a Caple-appointed engineer.
Appliances can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the safe use of the appliance.
Children must not play with this appliance.
When not in use and before cleaning, always isolate the appliance from the electrical supply.

Installation
Refer to the instruction manual for detailed installation instructions.

Operation
Follow these steps to operate the Wall Chimney Hood:

Ensure the power supply cord is properly connected and not damaged.
Turn on the hood using the control buttons or switches.
Adjust the fan speed and lighting as desired.
Cook and use your gas hob as usual, ensuring that naked flames are not left under the extractor.
After cooking, turn off the hood and disconnect it from the power supply when not in use.

Care and Maintenance
Refer to the instruction manual for detailed care and maintenance instructions.

Troubleshooting
Refer to the instruction manual for troubleshooting tips and solutions.

Product Dimensions
Refer to the instruction manual for the specific dimensions of the Wall Chimney Hood model you have.

Caple Contact Details
If you need spare parts or further assistance, contact Caple at 0117 938 7420 or visit their website at www.caple.co.uk.

INTRODUCTION

Thank you for choosing this Caple extractor hood.

To ensure that you get the best results from your
new extractor, we strongly suggest that you read this instruction manual thoroughly before use. If treated with care, your Caple extractor should give you years of trouble-free use.
To register ownership, please ensure you complete and return the guarantee card supplied with the appliance or visit www.caple.co.uk and register here.
This instruction manual is designed to provide you with all the required information related to the installation, use and maintenance of the appliance.
This hood is designed to extract unpleasant odours from the kitchen; it is not intended to extract steam. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and use.
The cooker hood uses high quality materials and is made with a streamlined design. Equipped with an electric motor and centrifugal fan, it provides strong extraction with low noise. It also features non-stick grease ﬁlters and an easy installation.

IMPORTANT

This appliance must only be used for the purpose it is intended. Other types of use are not permitted and may prove dangerous. Caple will not be held liable for any damage caused by the incorrect use of the appliance.
Do not use any accessories or attachments not recommended by Caple as this may result in ﬁre, electric shock or injury.
To protect against ﬁre, electrical shock and injury to persons, do not immerse cords or plugs in water or any other liquid.
Never touch the appliance with wet or damp hands.
Never pull the power cable as you could damage it.
If the appliance is faulty, do not attempt to repair it. Isolate it from the mains electric supply and contact Caple Service either by phone 0117 938 7420 or email service@caple.co.uk
Keep all packaging (including plastic bags, polystyrene foam etc) out of the reach and away from children.
Do not rest large or unstable objects on any part of the appliance.

Caple cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that Caple reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualiﬁed personnel.

SAFETY INSTRUCTIONS

Never let children operate the machine.
The cooker hood is for home use only, not suitable for barbecuing, restaurants or other commercial purposes.
The cooker hood and its ﬁlter should be cleaned regularly in order to keep in good working condition.
Clean the cooker hood according to the instruction manual to reduce the risk of ﬁre.
When using a gas hob, do not leave naked ﬂames under the extractor.
Before connecting this appliance check that the power supply cord is not damaged.
If the room where the hood is to be used contains a fuel-burning appliance such as a central heating boiler then its ﬂue must be of the sealed or balanced ﬂue type. If other types of ﬂue or appliances are ﬁtted ensure that there is an adequate supply of air to the room.
The air must not be discharged into a ﬂue that is used for exhausting fumes from appliances burning gas or other fuels.
Regulations concerning the discharge of air have to be conformed to.
Do not ﬂambé under the cooker hood.
Never leave frying pans unattended during use as over-heated fats and oils may catch ﬁre.
To ensure the best performance, we recommend switching on the extractor 15 minutes before cooking and leave it running 15 minutes after. This will ensure that the air in the kitchen is being circulated before cooking commences and the air is being cleaned after cooking has ﬁnished.
The performance of your extractor will vary depending on a number of factors. These include type of extraction, room volume, length of ducting, ventilation available and the cleanliness of the ﬁlters.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and user maintenance must not be made by children without supervision.
Never immerse the appliance in water.
This appliance is intended to be used in household and similar applications such as:
- Staff kitchen areas in shops, ofﬁces and other working environments.
- Farm Houses.
- By clients in hotels, motels and other residential-type environments.
- Bed and breakfast type environments.
To avoid all risk, if the power cable is damaged, it must only be replaced by a Caple-appointed engineer.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children must not play with this appliance.
When not in use and before cleaning, always isolate the appliance from the electrical supply.

ELECTRICAL SHOCK HAZARD

Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualiﬁed engineer.
Failure to follow these instructions can result in death, ﬁre, or electrical shock.
This appliance must be connected to the mains by a competent person. We recommend that the appliance is connected by a qualiﬁed electrician who is a member of the N.I.C.E.I.C who will comply with the I.E.E and local regulations. Electrical information can be found on the rating plate.

ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. This appliance is marked according to the European directive on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local council, your household waste disposal service or the retailer where you purchased the product

WARRANTY

Your new appliance is covered by warranty. The warranty card is enclosed – if it is missing, you must provide the following information to your retailer in order to receive a replacement: date of purchase, model and serial number. Registration can also be completed online by visiting www.caple.co.uk.

Ensure you keep your warranty card safe, you may need to show it to Caple Service together with proof of purchase. If you fail to show your warranty card you will incur all repair charges. Spare parts are only available from Caple Service and spare parts authorised centres.

DECLARATIONS OF CONFORMITY

CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all applicable legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).

UKCA DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all applicable legislation.

TECHNICAL FICHE
This appliance conforms to all current and applicable energy regulations. To view the Technical Fiche that supports the energy labelling data, please visit the product page on our website www.caple.co.uk.

INSTALLATION

PREPARE FOR THE INSTALLATION:

If you have an outlet to the outside, your cooker hood can be connected as per the below picture by means of an extraction duct with an interior diameter of 150mm.
Before installation, turn the unit off and unplug it from the outlet.
The cooker hood should be placed at a minimum distance of 65~76cm above the hob. It is the manufacturer of the hob who determines the clearance required and the clearance quoted by the hob manufacturer must be followed. In the absence of any instructions supplied with a gas hob the minimum distance between the hob and the hood must be at least 760mm.

WARNING:

Observe the warning concerning the operation of the appliance when air is discharged from the room.
When the cooker hood and appliance supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4×10-5 Bar).
Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws and screw plugs provided. $caple-FGC620-Wall-Chimney-Hood-fig- $4$$

Level up the cooker hood and hang onto the wall bracket hook. $caple-FGC620 -Wall-Chimney-Hood-fig- $5$$

After hanging the hood on the bracket, remove the grease filters, mark 2 holes inside the hood for safety screws. After marking, remove the hood, drill two holes and insert 2 wall plugs and finally fix the safety screws with 2 screws (ST4x30mm).

$caple-FGC620-Wall-Chimney-Hood-fig- $6$$

Fix the one-way-valve to the air outlet of the cooker hood. Then, attach the exhaust pipe onto the one-way-valve as shown below.

CHIMNEY INSTALLATION

Place the upper chimney into the lower chimney.
Attach the lower chimney bracket to the lower chimney.
Mark and drill 2 holes to fix the lower chimney bracket with 2 wall plugs and 2 screws ST4x30mm.

$caple-FGC620-Wall-Chimney-Hood-fig- $8$$

Slide the chimney to adjust the chimney height. When the height you require is reached, mark and drill the ﬁxing hole and ﬁx the upper chimney bracket with 2 wall plugs and 2 screws ST4x30mm. Fix the upper chimney with the upper chimney bracket using 2 scews ST4x8mm.

$caple-FGC620-Wall-Chimney-Hood-fig- $9$$

INSTALLATION – RECIRCULATION MODE
If you do not have an outlet to the outside, the exhaust pipe is not required (as shown in the section “Installation – ducted”), and charcoal ﬁlters must be installed.

INSTALLING THE CHARCOAL FILTER (CAP61CF)
An activated charcoal ﬁlter can be used to trap odours. In order to install the charcoal ﬁlter, the grease ﬁlter should be detached ﬁrst. Press the release button and pull it downward as shown below.

Fit the activated charcoal ﬁlter onto the side of the motor and turn it in a clockwise direction to lock into place. Repeat the same on the other side . $caple-FGC620-Wall-Chimney-Hood-fig- $11$$

Scan the QR Code to access the ‘How To’ video.

$caple-FGC620-Wall-Chimney-Hood-fig- $12$$

NOTE:

Make sure the ﬁlter is securely locked. Otherwise, it may loosen and be dangerous.
When using a charcoal ﬁlter, the extraction power may be slightly reduced.
We recommend replacing these ﬁlters every 6 months. Replacement ﬁlters (CAP61CF) can be purchased directly from www.caple.co.uk.

OPERATION

OFF BUTTON
Switches the extraction fan off.
LOW-SPEED BUTTON
Is suitable for simmering and cooking which does not produce much odour.
MEDIUM SPEED BUTTON
Airflow speed is ideal for extracting with standard cooking.
HIGH-SPEED BUTTON
When a high amount of smoke or odour is produced, press the high-speed button for the most effective extraction.
LIGHT BUTTON
Switches the light on and off.

CARE AND MAINTENANCE

IMPORTANT:
Before cleaning or maintenance please switch off the electricity supply and remove the plug from the wall.

REGULAR CLEANING
Use a soft damp cloth with lukewarm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material, abrasive cleaning creams or stiff brushes to clean the appliance.

CLEANING THE GREASE FILTER
Clean the ﬁlter every month to help minimize the risk of ﬁre. The ﬁlter collects grease, smoke and dust, therefore the ﬁlter is directly affecting the efﬁciency of the cooker hood. If not cleaned, the grease residue (which is potentially ﬂammable) will saturate the ﬁlter. It can be easily cleaned with warm water and washing up liquid, alternatively, the ﬁlters can be cleaned in your dishwasher. Please ensure no other items are washed with the ﬁlters, they must be washed separately to prevent food from becoming trapped in the gauze. Cleaning the grease ﬁlters in the dishwasher may lead to discoloration, this is normal and is not a fault with the product.

REPLACING YOUR CHARCOAL FILTER
This only applies if you are using the hood in recirculation mode (not vented to the outside). The charcoal ﬁlter traps your cooking odors and they need to be replaced, this can vary depending on how frequently the cooker hood is used. We recommend replacing them at least every 6 months.

This extractor uses CAP61CF charcoal ﬁlters. Filters can be purchased directly from www.caple.co.uk.

REPLACING THE BULB

NOTE:
The lights must be replaced by a qualified person.

Switch the unit off and unplug the appliance.
Remove the lamp cover by unscrewing the 2 screws.
Replace with the same type and rated bulb/lamp fixing. LED lamp (max.1.5W).

LIGHT SOURCE ENERGY CLASS
This product contains a light source of energy efficiency class G.

TROUBLESHOOTING

FAU LT	CAUSE	SOLUTION
The lights on, but the fan does not work	The fan blade is jammed.	Switch off

the unit and contact

Caple Service. To be repaired by qualified service personnel only.

Caple Service. To be repaired by qualified service personnel only.

The fan motor is not fixed tightly.| Switch off the unit and contact

Caple Service. To be repaired by qualified service personnel only.

The unit is not hung correctly on the bracket.| Take down the unit and check whether the bracket is in the correct location.
The extraction performance is not good| The filter requires cleaning.| Clean the grease filter as directed in the ‘Care and Maintenance’ section. Replace the charcoal filter (if in recirculation mode).

If the above table has not solved the problem please contact Caple Service by phone on 0117 938 7420 or by email service@caple.co.uk.