Moes ZigBeeRF Smart Curtain Blinds Shutter Touch Switch Instruction Manual
- June 12, 2024
- MOES
Table of Contents
Moes ZigBeeRF Smart Curtain Blinds Shutter Touch Switch
Product Description
This new designed glass panel wireless touch smart curtain switch is designed with many new updates.The ZigBee+RF version easily replaces traditional switches with a variety of ways to control. Multi-control association is added into Tuya Smart Life App as a new feature to control with other smart switches,together with the backlight on/off and relay status when power off.Its scratch resistance glass panel is suitable for different decoration styles with its best value.
Safety Information
Risk of Electric Shock: Electricity can cause personal injury and property damage if handled improperly. If you are not sure about any part of these instructions, please seek professisonal assistance from a qualified electrician.
Technical Parameters
- Model: ZTS-EUR-C / ZTS-USR-C
- Working Voltage: 90-250V AC 50/60Hz
- Current: 2.5A
- Load Power: ≤600W
- Standby Power:≤ 0.5W
- Wireless Protocol: Z igBee 3.0+RF 433MHz
- Standby Consumption: 0.1mA
- Wireless Range: 30 Meters(Indoor)
- Switch Standard: 8686mm / 11872mm
Warnings: Turn off the power at the circuit breaker and test that power is off before wiring.
Installation
Note:
- Make sure that the power at the circuit breaker is off before wiring.
- Neutral Wire is required.Confirm the wall box contains a Neutral Wire(typically white).If the wall box don’t have a Neutral Wire,please try another location at your home or call a professional electrician to install the switch.
- The wire colors indicated in this manual are the usual colors and may differ in some houses.
- Ensure the wire conductors are securely fastened to each wire.
- Ensure the Wi-Fi signal is steady and normally working before wiring.
- If you don’t have any wiring experience,please call a professional electrician.
Step 1
Step 2
- Remove the old switch
Step 3
- Remove the switch and pull it away from the wall.
ldentify Line/Load Wire(Note:The color of your wire may be different from the color shown on the manual.)
Verify power is off
- We recommend you remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit.
- You may need to turn off more than one circuit breaker.
Step 4
Take pictures of the wiring
Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.
Step 5
Open the switch panel from the bottom of the switch with a screwdriver
Mount the switch with the provided screws and snap the wall plate on it.
Step 6
Turn the power back on at the circuit breaker and then switch the light on.
Add Devices
Download Smart Life
Please scan the QR code or download Smart Life on App store.
Registration or Log in
- Download “Smart Life”Application
- Enter the Register/Login interface;tap “Register” to create an account by entering your phone number to get verification code and “Set password”.Choose “Log in” if you already have a Smart Life account.
Configure the APP to the switch
Preparation : Ensure the switch has been connected with electricity; ensure your phone has been connected to Wi-Fi and is able to connect to the Internet.
Note:
The switch only supports 2.4G network.If you have connected 5G network,please disconnect 5G network firstly and connect 2.4G network.
ZigBee link method
- Re-pair and clear up the ZigBee code
- Press the switch button for 6 times,hold on on the 6th time and then release your finger until the blue indicator flashes fast for succseeful pair.
-
Open the App, select “+” on top right,choose “Switch (Zigbee)” to add device.And select the right Gateway to confirm the connection.
Note: Make sure you have successfully connected one Zigbee gateway hub .
-
Confirm the Zigbee switch blue indicator is flash fast (twice a second).
-
The connecting will take about 10-120 seconds to complete depending on your network condition.
-
When pairing is done, the Zigbee curtain switch will be shown on the App.
How to Reset/Re-pair ZigBee code
Press the switch button for 6 times,hold on on the 6th time and then release
your finger until the blue indicator flashes
1fast for succseeful reset.
Remote radio frequency(RF)link method: 2Pair and clear up the RF code
-
How to pair the RF cod e
Long press the switch button for 5 seconds for learning the code and it will automatically exit when it fails to learn and pair. The indicator will recover to its original state when the code is learned successfully. -
How to clear up the RF code
Long press the switch button for 5 seconds and do not release your finger until the indicator stops blinking for successful code clearing.
Note: This operation can only clear one button,repeat the operations for clearing other codes.
Set your Echo speaker by Alexa APP
-
If you have finished installing Smart Life,just open Amazon Alexa App;log into your Alexa account with password.
-
Click the menu on the top left -click “settings”,choose “Set up a new device”(choose a device like Echo)
Note:
When below page appears,long press the small dot on your Echo device until the light turns to yellow.Then click “Continue”on the App.
Attention: The mobile phone can not open a variety of VPN software. -
Choose your own Wi-Fi and wait for a few minutes.After watching an introduction video,click “next step”,then it will enter Home page automatically.Now the Echo has been connected to Wi-Fi successfully.
Enter Smart Life Skill in Alexa APP
-
Complete product networking configuration in the App
Complete the device’s networking configuration according to the prompts in the App.
Note: In the App, change the name of the device to an easily identifiable name such as Alexa; names are usually in English, such as “bed light”. -
Configure the Amazon Echo device
(If you have already configured Amazon Echo, you can skip this step. The following instructions are based on the iOS client.)- Make sure you Amazon Echo device is powered on and connected to a Wi-Fi network.
- Open the Alexa App on your phone. After successful login, tap on the menue in the upper left corner of the Home page, select “Settings” and tap “Set Up A New Device” to set up the Amazon Echo.
- Choose your Amazon Echo device type and language for connecting. Press and hold the small dot on the device until the light turns yellow. Then tap “Continue” to connect to the hotspot.
- After connecting to the Amazon Echo hotspot, return to the page. At this point, the connection is successful.
Tap “Continue” to proceed to the next step. Choose a Wi-Fi network to connect to. Amazon Echo will take a few minutes to try to connect to the network.
After the network connection is successful, tap “Continue”. An introduction video will appear. After the video ends, tap “Continue” to jump to the Alexa Home page. You have now completed the Amazon Echo’s configuration process.
-
Key step —— Link Skill
Tap on “Skills” in the Alexa App menu.
-
Then search for “App Name”. Tap “Enable” to enable the Skill.
-
Enter the App account and password, then tap “Link Now” to link your App account to enable the Skill. Now you can start your smart home journey.
Common commands
- Control the device via voice commands, now you can control your smart device with Echo. You can control your device (such as your bedroom light) with the following commands:
- Alexa, turn on/off bedroom light. (Turn on/off the light) Alexa, set bedroom light to 50 percent. (Set the light to any brightness)
- Alexa, brighten/dim bedroom light. (Increase/weaken the brightness of the light)
- Alexa, set bedroom light to green. (Adjust the color of the light)
SERVICE
- During the free warranty period, if the product breaks down during normal use, we will offer free maintenance for the product.
- Natural disasters/man-made equipment failures, disassembly and repair without the permission of our company, no warranty card, products beyond the free warranty period, etc., are not within the scope of free warranty
- Any commitment (oral or written) made by the third party (including the dealer/service provider) to the user beyond the warranty scope shall be executed by the third party
- Please keep this warranty card to ensure your rights
- Our company may update or change the products without notice. Please refer to the official website for the updates.
RECYCLING INFORMATION
All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.
WARRANTY CARD
Product Information
- Product Name_____
- Product Type_____
- urchase date__
- Warranty Period___
- Dealer Information_____
- Customer’s Name__
- Customer Phone___
- Customer Address_____
Maintenance Records
Thank you for your support and purchase at we Moes, we are always here for
your complete satisfaction, just feel free to share your great shopping
experience with us.
If you have any other need, please do not hesitate to contact us first, we will
try to meet your demand.
FOLLOW US
- FB: @moessmart
- TW: @moes_smart
- INST: @moes_smart
- Y OUTUBE : moes
- TIKTOK: @moes_smart
- E: www.moes.net
Wenzhou Nova New Energy Co.,Ltd.
- Address: 4th Floor, Building 2, Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
- Tel: +86-577-57186815
- Email:service@moeshouse.com
- AMZLAB GmbH Laubenhof 23, 45326 Essen
- Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>