SEALEY LED139 13W SMD Rechargeable Underbonnet LED Light Instruction Manual

13W SMD RECHARGEABLE UNDERBONNET
LED LIGHT
MODEL NO: LED139

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE  AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

1.1. GENERAL
It is important to ensure that the lamp is fully charged before initial use.
DO NOT turn the lamp on when it is being charged.
DO NOT shine directly into your, another person’s or an animal’s eyes.
DO NOT allow children to use the lamp.
DO NOT leave battery in a discharged state. Recharge battery immediately.
Recharge the battery at least once every six months of non-use.
‰ WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using this light. Account for all tools being used and DO NOT leave them in or near the engine.
1.2. BATTERY SAFETY
‰ WARNING! To reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
DO NOT expose to temperatures above 60°C (140°).

INTRODUCTION

Rechargeable Underbonnet 1200 Lumen LED work light with 3 brightness settings. 90-degree swivel handle for adjustable lighting angle. Rotating hook and magnets on either end for ease of use within the workshop. 3.7V 4400Ah Li-ion battery and 1.3m USB charging cable included. Maximum 4hr run time.

SPECIFICATION

Model No …………………………………………………………LED139
Battery …………………………………3.7V 4400Ah Li-month Li-ion
Charging Time ……………………………………………………4 – 6hrs
IP Rating ………………………………………………………………IPXX
LED Qty ………………………………………………………………… 100
LED Type …………………………………………………………….. SMD
Lumen Output …………………………………………………… 1200lm
Operating Time ……………………. High 1hr, Mid 2hrs, Low 4hrs
Power ……………………………………………………………………13W

OPERATION

4.1. OPERATIONAL MODES (Refer to fig.1)
4.1.1. Press the On/Off button once to turn the unit on. This will also light up the four LEDs (fig.1) to indicate the battery state. 4 bars lit
indicates 100%, and 1 bar lit indicates 25% (or less).
4.1.2. Press the On/Off button again and the unit operates in full power mode.
4.1.3. Press the On/Off button again and the unit operates in mid-power mode.
4.1.4. Press the On/Off button again and the unit operates in low power mode.
4.1.5. Press the On/Off button again and the unit switches off.
4.2. UNIT MOUNTING AND ADJUSTMENT (Refer to fig.2)
4.2.1. The unit is fitted with a hook at each end to enable suspension from a suitable source.
4.2.2. The unit also has a magnet at each end to allow it to be supported by a ferrous surface/object.
4.2.3. To enable lighting position adjustment, the unit is fitted with hinging/rotating elbows at both ends.
4.2.4. Pull the end caps out to expose the joint (fig.2). Each elbow can be rotated at 180° and in one of 9 set positions.

MAINTENANCE

5.1. Keep the lamp clean and check for damage before every use. If damage is observed, remove from use until unit is repaired.

Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
BATTERY REMOVAL / REPLACEMENT
Remove the screws in the black section of the lamp control section to remove the batteries.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
WEEE REGULATIONS**
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk

© Jack Sealey Limited
Original Language Version
LED139 Issue 1 17/03/22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>