Delta Crib Instruction Eclipse 4-in-1 Crib User Guide

Delta Crib Instruction Eclipse 4-in-1 Crib

READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store from where it was purchased before contacting Delta Children’s Products Customer Service..
Make sure that all preassemble parts are tight. The appearance of your product may be different from that pictured in this booklet.
To register your product for important safety alerts and updates to your product please visit http://deltaenterprise.com/register.asp

CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES.

WARNING: CRIB

Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an infant.
Failure to follow these warnings and the assembly instructions could result in serious injury or death.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.

ADULT ASSEMBLY REQUIRED DUE TO SMALL PARTS.

• Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
• Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
• Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
• Strangulation Hazard: Do not place crib near window where cords from blinds or drapes may strangle a child.
• Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib has an adjustable mattress support. For the convenience of the parent when the baby is very small, the mattress support may be used in the highest position. Important: with the mattress support and mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches higher then the top surface of the mattress. If it is not, lower the mattress support and the mattress to the next highest position.
• Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (90cm), whichever occurs first. The child should be placed in a youth or regular bed.
• Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly and frequently during use. Do not use crib if any parts are missing, damaged or broken. Contact Delta Children’s Products for replacement parts and instructional literature if needed. Do not substitute parts.
• Follow warnings on all products in a crib.
• Do not use a water mattress with this crib.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
• Infants can suffocate in gaps between crib sides and a mattress that is too small.
• Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that every component is properly and securely in place.
• To avoid head injury, do not allow any child to play underneath the crib.
• Never add an accessory such as a bassinet or changing table that extends over the sleeping area.

WARNING: DO NOT USE THIS CRIB IF THE ENCLOSED OR ATTACHED INSTRUCTIONS CANNOT BE STRICTLY ADHERED TO. DO NOT USE THIS CRIB IF THE CHILD IS ABLE TO CLIMB OUT UNAIDED OR IS TALLER THAN 90 CM. DO NOT PLACE CORDS, STRAPS OR SIMILAR ITEMS THAT COULD BECOME WOUND AROUND THE CHILD’S NECK IN OR NEAR THIS CRIB.

ENSURE THAT THE SIDES ARE PROPERLY LATCHED OR LOCKED IN PLACE WHEN THE CRIB IS OCCUPIED. THE MATTRESS USED WITH THIS CRIB SHOULD NOT BE MORE THAN 15 CM THICK AND SHOULD BE OF SUCH LENGTH AND WIDTH THAT THE GAP BETWEEN THE MATTRESS AND THE SIDES OF THE CRIB IS NOT MORE THAN 3 CM WHEN THE MATTRESS IS PUSHED INTO THE CORNER OF THE CRIB.

TODDLER BED

WARNING ENTRAPMENT/STRANGULATION HAZARD

• INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT AND STRANGULATION. Failure to follow these warnings and the assembly instructions could result in serious injury or death.
• Never use bed with children under 15 months.
• Never place bed near windows where cords from blinds or drapes may strangle a child.
• Do not place items with a string, cord, or ribbon around a child’s neck, such as hood strings or pacifier cords.
• Do not suspend strings over a toddler bed for any reason.
• The users maximum weight shall not be greater than 50 lb (22.7kg).
• The mattress intended for use on the bed shall be a full-size crib mattress having minimum dimensions of 51 5/8 in. (1310 mm) in length, 27 1/4 in. (690 mm) in width and 4 in. (100 mm) in thickness.
• Stabilizer bar must be used when converted to a toddler bed.

NOTES ON ASSEMBLY:

• During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape specified in the instructions.
• To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON USE:

Keep children and others safe by following these simple rules:

• Do not allow any child to play on furniture
• Do not allow climbing on any piece of furniture.
• Do not allow hanging from any piece of furniture.
• Always monitor your child’s activity when in the nursery.

NOTES ON CARE AND MAINTENANCE:

• Do not scratch or chip the finish.
• Inspect the product periodically, contact delta children’s products for replacement parts or questions.
• Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement. These extremes can cause a loss of structural integrity.
• To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad under any items you place on the finish.
• Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
• Do not use abrasive chemicals.
• Do not spray cleaners directly onto furniture.
• Lift slightly when moving on carpeting to prevent leg breakage.
• Use of a vaporizer near furniture will cause wood to swell and finish to peel.

PARTS

MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.

POUCH ATT ACHED T O MATTRESS SUPPORT

• KEE P INSTRUCTIONS AND AN Y EXTR A HARD W ARE AND T OOLS IN THIS POUCH AFTER ASSEMBLY WARNINGS REL A TED T O THE SAFE USE OF THIS CRIB ARE PRINTED ON THE POUCH

HARDWARE AND TOOLS

CRIB ASSEMBLY

STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP

ATTACH (1) LEFT CRIB END (PART E) TO (1) LEFT REAR LEG (PART C) AND (1) LEFT FRONT LEG (PART G) USING (1) M4x30mm METAL PINS (PART T), (2) M6x45mm BOLTS (PART P) AND (3) M6x40mm BOLTS (PART R). TIGHTEN WITH THE M4 ALLEN WRENCH. USE THE FLAT HEAD SCREWDRIVER TO HOLD THE BARREL NUT IN THE PROPER ALIGNMENT.
REPEAT ON THE RIGHT CRIB END (PART F).

NOTE: AFTER ASSEMBLY, THE “STEPPED HOLES” IN BOTH POSTS ARE ON THE SAME SIDE.

STEP 2

ATTACH (1) BACK RAIL BOTTOM (PART B) TO THE ASSEMBLIES FROM STEP 1 USING (4) M6x55mm BOLTS (PART P) .
INSERT THE TENON OF THE BACK RAIL TOP (PART A) INTO THE SLOT ON TOP OF THE BACK RAIL BOTTOM (PART B), THEN INSERT THE M6x55mm BOLTS (PART N), THROUGH THE LEGS INTO THE INSERT NUTS ONTO THE BACK RAIL TOP (PART A) AS SHOWN.
TIGHTEN WITH THE M4 ALLEN WRENCH.

NOTE: THE SLOT IN PART B MUST FACE UP.

STEP 3

ATTACH THE MATTRESS SUPPORT (PART L) IN ALL CORNERS USING (1) M6x15mm BOLT (PART S) IN EACH CORNER.TIGHTEN WITH THE M4 ALLEN WRENCH.

THE WARNINGS PRINTED ON THE POUCH ATTACHED TO THE MATTRESS SUPPORT MUST FACE UP, THE SPRINGS MUST FACE UP.
THIS CRIB HAS (3) ADJUSTMENT POSITIONS, USE THE HIGHEST ONLY FOR NEW BORNS, MOVE THE MATTRESS DOWN AS THE CHILD GROWS.

WARNING:
FALL HAZARD : WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.

STEP 4

ATTACH (1) FRONT RAIL (PART J) TO THE ASSEMBLY FROM STEP 3 USING (8) M6x55mm BOLTS (PART N). TIGHTEN WITH THE M4 ALLEN WRENCH.

STEP 5

STORE THE ASSEMBLY INSTRUCTION BOOKLET AND THE ALLEN WRENCH IN THE POUCH ATTACHED TO THE MATTRESS SUPPORT.

WARNING: SEE PAGE 2 FOR INFORMATION

TODDLER BED CONVERSION

STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP

REMOVE THE FRONT RAIL INSTALLED IN STEP 4 OF SECTION 1 CRIB ASSEMBLY.

STEP 2

ATTACH (1) STABILIZER BAR (PART K) TO THE ASSEMBLY FROM STEP 1 SECTION 2 USING (2) M4x30 mm METAL PINS (PART T), (2) M6x80 mm BOLTS (PART M) AND (2) BARREL NUTS (PART U).
GENTLY PULL THE LEFT AND RIGHT FRONT LEG APART. TO INSTALL THE STABILIZER BAR – BE VERY CAREFUL NOT TO SCRATCH THE FINISH.
USE THE FLAT HEAD SCREWDRIVER TO HOLD THE BARREL NUT IN THE PROPER ALIGNMENT.
TIGHTEN WITH THE ALLEN WRENCH.

STEP 3

WARNING
SEE PAGE 3 FOR TODDLER BED WARNINGS

THE MATTRESS SUPPORT MUST BE IN THE LOWEST POSITION.
STORE ALL HARDWARE SAFELY.
READ ALL WARNINGS ON PAGE 3

AS SHOWN, USE AS A DAY BED OR LOVE SEAT SOFA.
DO NOT USE WITHOUT STABILIZER BAR INSTALLED.

STABILIZER BAR MUST BE USED WHEN CONVERTED TO A TODDLER BED.

A TODDLER BED GUARDRAIL IS AVAILABLE FOR THIS CRIB.
PLEASE SEE YOUR CRIB RETAILER, VISIT WWW.DELTACHILDRENSPRODUCTS.COM OR CONTACT DELTA CONSUMER CARE
FOR MORE INFORMATION.
THIS CRIB USES DELTA STYLE #__
GUARDRAIL.

FULL SIZE BED CONVERSION

STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP

YOU HAVE THE OPTION TO CONVERT THE CRIB TO A FULL SIZE BED. SIMPLY FOLLOW STEPS IN REVERSE ORDER TO DISASSEMBLE THE CRIB. THEN REMOVE THE REAR LEGS FROM THE LEFT CRIB END (PART E) AND RIGHT CRIB END (PART F) WITH THE M4 ALLEN WRENCH AS SHOWN.

ATTACH THE LEFT FRONT LEG (PART G) AND THE RIGHT FRONT LEG (PART H) TO THE FRONT RAIL (PART J) WITH (8) M6 x 55mm BOLTS (PART N),USING THE M4 ALLEN WRENCH AS SHOWN.
STORE ALL PARTS AND HARDWARE IN A SAFE PLACE.

STEP 2

ATTACH ADAPTER PLATES (V) TO BOTTOM OF REAR SIDE RAIL LEGS USING (4) M6x15mm BOLTS (PART S). HAND TIGHTEN BOLTS IN PLACE.
ADJUST UP OR DOWN TO ALLOW FOR CONNECTION TO BED RAIL. ADAPTER “TABS” WILL KEEP ADAPTER PLATE FROM ROTATING .

STAND HEADBOARD UP. ATTACH TO BED FRAME WITH BOLTS AND NUTS (SUPPLIED BY BED FRAME MANUFACTURER). ADAPTER PLATES (V) CAN BE ADJUSTED UP OR DOWN TO BEST SUIT BED FRAME. TIGHTEN ALL BOLTS ONCE BED RAIL IS ADJUSTED.

NOTE: BED FRAMES ARE NOT SUPPLIED WITH THIS SYSTEM, BUT CAN BE PURCHASED AT MATTRESS STORES.

Customer Service:
Web Site: www.deltachildrensproducts.com
Delta Children’s Products
114West 26th Street
New York, NY 10001
Tele.212-645-9033

Warranty: This Delta Crib is warranted to be free from defects for a period of 1 year from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.

To register your product for important safety alerts and updates to your product please visit http://deltaenterprise.com/register.asp

Please do not return this item to the store before contacting us about missing parts or with any questions.

To report a problem, please log on to www.deltachildrensproducts.com and click the Customer Service
Tab, log on to www.deltaenterprise.com/customer_service.asp, or contact us by phone at 212-645-9033.
In the event that you need to contact our customer service department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be found on the label on the Crib End bottom rail.
Style No.:
Lot No. :
Pack Date:
Date of Purchase: _____ (you should also keep your receipt)

Download PDF:Delta Crib Instruction Eclipse 4-in-1 Crib User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>