COLORSTEEL Profiles Steel Roofing and Cladding User Guide

September 18, 2024
COLORSTEEL

Profiles Steel Roofing and Cladding

“`html

Specifications:

  • THICKNESSES: 0.40, 0.55, 0.75 mm BMT (Base Metal Thickness).
    Other thicknesses available on request.

  • MATERIAL GRADE: G300 or G550.

  • ROOFING: Roof and canopies of all building types.

  • WALL CLADDING: Lined and unlined walls of enclosed
    buildings.

  • CURVING: Can be crimp curved (trapezoidal) or roll curved
    (corrugate).

  • PROFILES:

    • All corrugate profiles
    • All trapezoidal profiles
    • Approved trough section (secret fix) profiles
  • PHYSICAL PROPERTIES:

    • FIBER: Polyester
    • WEIGHT: 80 g/m2
    • THICKNESS: 1.2 mm

Product Usage Instructions:

Design Considerations:

Where safety netting is not used, the use of trafficable
translucent sheeting is recommended to reduce the hazard of
fall-through.

Scope of Use:

The product is suitable for roofing, wall cladding, and curving.
Thickness options are available upon request.

Compliance:

  • The product enhances internal moisture management by absorbing
    condensation and improving natural ventilation.

  • Not recommended for flashings or rainwater accessories.

  • Recommended for corrugate and trapezoidal profiles only.

Transport and Installation:

  • Inspect sheets for damage before installation.

  • Ensure hands and surfaces are clean before handling the
    product.

  • Avoid dragging sheets over rough or dirty surfaces.

  • The supporting structure should comply with NZ 3604 or AS/NZS
    1170 for structural integrity.

Warranty and Assistance:

**WARRANTY OVERVIEW FOR ROOFING ONLY***

MILD: 50 years

MODERATE: 40 years

SEVERE: 30 years

VERY SEVERE: 20 years

EXTREMELY SEVERE: Not recommended

  • This chart is a guide only. For full warranty details and
    technical assistance, contact:
    Phone: 0800 697 833
    Email: specifications@colorsteel.co.nz

FAQ:

Q: What profiles is the product suitable for?

A: The product is suitable for all corrugate profiles, all
trapezoidal profiles, and approved trough section (secret fix)
profiles.

Q: How can I ensure proper ventilation with this product?

A: The product enhances ventilation by absorbing condensation
and improving natural airflow within the roof space.

Q: What is the recommended warranty period for different

environmental categories?

A: The warranty period ranges from 15 to 50 years based on the
environmental category. Refer to the warranty overview for
details.

“`

FOR SUPERIOR MOISTURE MANAGEMENT

Design Guide

2

COLORSTEEL DRIDEX®

Dridex® combines the proven history and performance of COLORSTEEL® with an absorbent fleece material that’s bonded to the underside of the sheet.
This thin layer of absorbent fleece completely replaces the need for traditional roofing underlay, allowing for enhanced absorption of condensation and superior air flow within the roof space. The fleece operates on the same principles as traditional underlay. It will absorb moisture when the cavity space reaches dew point and then release it when ambient conditions improve. Following extensive testing and validation with external assessment, Dridex® has proven performance in the market since 2016.
Enhanced absorption of condensation and superior air flow within the roof space
3

“Using COLORSTEEL DRIDEX® for the Mainfreight depot in Mount Maunganui allowed our team to lay 25m sheets in all wind conditions. No wind delays meant we could keep to a tight building programme and achieve an early enclosure”
TERRY HUNT TH COMMERCIAL ROOFING.

Productivity
Wind often prevents the safe laying of roofing, particularly in the afternoons when the wind typically increases. In Auckland, the wind will interrupt the laying of short lengths of roofing on approximately 30% of days and more frequently for longer lengths.
With no need to lay separate underlay, Dridex® can be laid in 90% of wind conditions so installation is less likely to be interrupted by high winds.
Using Dridex® significantly increases the speed of installation and means an earlier enclosure can be achieved. An independent review conducted by Beacon Pathway found that using Dridex® can save time and improve productivity in excess of 25%.
Healthier
The Asthma and Respiratory Foundation of New Zealand reports that respiratory disease affects 1 in 7 New Zealanders. By delivering superior condensation absorption and enhanced ventilation, Dridex® creates drier and healthier internal environments. This leads to the reduction of mould and pollutants which are often associated with asthma and other respiratory tract inflammations and allergies.
Dridex® has been awarded Sensitive Choice approval for its ability to manage internal moisture and resist mould growth in the ceiling cavity. A dry ceiling cavity is a warm and healthy ceiling cavity.
Improved Aesthetics
Compared to alternate products, Dridex® is less susceptible to degradation from mould, wind or bird attack. The result is a long-lasting clean and tidy appearance.

4

COLORSTEEL DRIDEX®

Absorbency (g/m²)

Why COLORSTEEL DRIDEX®?

Dridex® can be laid in 90% of wind conditions

90%

Using Dridex® can save time and improve productivity in excess of 25%

25%

Dridex® has been awarded Sensitive Choice approval, helping the 1 in 7 New Zealanders affected by respiratory disease

1 in 7

Dridex®

Conventional

400 350 300 250 200 150 100
50 0 COLORSTEEL DRIDEX®

NZS2295 Requirement

Superior Moisture Retention
The use of Dridex® will reduce the chance of excessive moisture build up and condensation run-off. When tested following AS/NZS 4201.6, Dridex® had an absorbency of 349 g/m2 (BRANZ test report DC10841), nearly twice the requirement for underlays detailed in NZS 2295.

Airflow Rate (m³/h)

12000 10000
8000 6000 4000 2000
0 0

5

10

15

20

25

30

Pressure Difference (Pa)

Improved Ventilation
By removing the air barrier of traditional underlay, Dridex® reduces the chance of accumulating moisture in the roof structure and any accompanying insulation.
Tests conducted on a straight gable roof reported that using Dridex® increased the calculated effective free vent area by 133%. This approximately doubled the air flow rates through the roof envelope at all wind pressures (BRANZ test report DC2950).

5

Design Considerations

Dridex® enhances natural ventilation of the ceiling cavity without the need for bulky or costly design additions.
This is especially important in flat roofs, sarked roofs, and skillion roofs, which are required by the MRM Code of Practice to have specific design features to ensure natural ventilation. BRANZ testing showed that on a straight gable roof, replacing roofing underlay with Dridex® increased the effective free vent area to exceed the minimum recommendation of 1:300.
Dridex® can be fastened directly to galvanized steel purlins or dry timber. It may be laid over galvanized netting or safety mesh. For exposed roofs, the use of safety mesh may be replaced by other safety mechanisms such as temporary safety netting or harnesses, to give a clean and uncluttered soffit.

Where safety netting is not used, the use of trafficable translucent sheeting is recommended to reduce the hazard of fall-through.
Blocking the free passage of air at eaves or apexes, using profiled closures or similar, will severely reduce the ventilation attributes of Dridex® and is not recommended. If required, eaves combs can be utilised to prevent the entry of birds.
As with all roofing materials, careful design is required to prevent the accumulation of excessive internal moisture in the ceiling cavity of skillion roofs when using Dridex®. Guidance on such can be found on the CodeMarkTM certificate (CM70050) and in BRANZ publication BU610 “Preventing moisture build up in timber framed skillion roofs”. Minimum roof pitch is not affected by using Dridex®.

COLORSTEEL DRIDEX® delivers a warmer, drier environment, offers superior air flow and saves time during installation.

6

COLORSTEEL DRIDEX®

Scope of Use

S U B S T R AT E Dridex® is supplied on COLORSTEEL® MaxamTM with ActivateTM technology.
THICKNESSES 0.40, 0.55, 0.75 mm BMT (Base Metal Thickness). Other thicknesses available on request.
MATERIAL GRADE G300 or G550.

COLOURS Available in the complete COLORSTEEL® range.
ROOFING Roof and canopies of all building types.
WALL CLADDING Lined and unlined walls of enclosed buildings.

CURVING Can be crimp curved (trapezoidal) or roll curved (corrugate).
ENVIRONMENT Dridex® — Roofing: Mild, Moderate, Severe,
Very Severe — Wall Cladding: Mild, Moderate, Severe,
Very Severe

PROFILES

All corrugate profiles

All trapezoidal profiles

Approved trough section (secret fix) profiles

PHYSICAL PROPERTIES
FIBER Polyester
80 g/m2 WEIGHT
1.2 mm THICKNESS
7

With no need to lay separate underlay, COLORSTEEL DRIDEX® can be installed in 90% of wind conditions

8

COLORSTEEL DRIDEX®

Compliance
COMPLIANCE When used and installed as roof cladding in accordance with the conditions and limitations stated in this document and in the CodeMarkTM certificate (CM70050), Dridex® will comply with the following clauses of the NZ Building Code.
B2 DURABILITY Dridex® is issued as a type 6 product in accordance with AS/NZS 2728.
C3 FIRE Dridex® is rated 1-S under the NZ Building Code clause 3.4(a), representing the best performance category in relation to resistance to flammability and smoke generation (the same rating shared by Zincalume® and COLORSTEEL®).
E2 EXTERNAL MOISTURE The performance of Dridex® products in resisting external moisture is identical to existing COLORSTEEL® products.
E3 INTERNAL MOISTURE The management of internal moisture is enhanced by the action of absorbing condensation and improving natural ventilation which facilitates extraction and drying.
HAZARDOUS MATERIALS As stated in the Material Safety Data Sheet (MSDS), COLORSTEEL® is not a hazardous material under normal conditions. MSDS available on request.
Conditions and Limitations
LIMITATIONS — Dridex® may be used in environments up to and including very
severe for both roofing & cladding. — Dridex® must not be installed in direct contact with absorbent
roofing underlay, except where required at verges. — Not recommended for flashings or rainwater accessories. — Recommended for corrugate and trapezoidal profiles only.
Contact your local Rollformer for advice on secret fix profiles.
BUILDING USE Dridex® recommended for the same residential and commercial building uses as MaxamTM. Specific advice should be sought when used on buildings with aggressive internal environments, such as swimming pools, intensive animal shelters, galvanizing plants and other activities that produce harsh internal environments.
SPECIAL CONDITIONS The drip edges of all sheets must be treated to prevent absorption of discharging rainwater through capillary action.

Transport and Installation
TRANSPORT & HANDLING Transport and loading As a pre-finished cladding material, Dridex® must be handled with due care. While loading, and during transport, the bottom sheets of bundles must be protected from damage. When unloading, bundles must be placed on clean dunnage clear of the ground.
Handling of sheets Inspect sheets for damage, and correct orientation of fleece clear of the overlap. Ensure hands and surfaces are clean of grease or dirt. Do not drag sheets over rough or dirty surfaces or sharp protrusions.
SUPPORTING STRUCTURE The supporting structure should be designed in compliance with NZ 3604 or AS/NZS 1170 to ensure structural integrity. Surfaces should be clean of grease and dirt that may stain the fleece, and free of sharp upstanding edges that will damage the under surface of the cladding.
INSTALLATION In addition to the recommendations and requirements of the COLORSTEEL® Installers Guide, the following requirements specifically apply to installing Dridex®: — To prevent absorption of water through capillary action, all drip
edges, including those discharging into a valley or above a roof penetration, must be treated to make them non-absorbent. This can be done by heat gun or flame, before or after installation. Some roll formers have in-line capacity to perform this end treatment during roll-forming, greatly reducing the need for on-site treatment of factory cut ends. — Minor damage to the fleece incurred during transportation or installation will not affect its performance. The fleece has a built-in pressure sensitive adhesive and marred fleece may be re-adhered to the sheet by use of a hard rubber roller. Alternatively, a patch may be rolled on to cover the damaged area. Major damage can only be repaired by replacing the affected sheet.
MAINTENANCE All COLORSTEEL® products must be maintained in accordance with the COLORSTEEL® Maintenance Recommendations guide or as per the COLORSTEEL® Warranty Certificate. If necessary the underside of the fleece may be cleaned with a low pressure water blaster or a soft brush application of warm water and detergent. Do not use solvent cleaners.

9

Warranty and Assistance

WARRANTY OVERVIEW FOR ROOFING ONLY*

MILD

Environmental Categories

MODERATE

SEVERE

VERY SEVERE

EXTREMELY SEVERE

Perforation¹ DRIDEX®
Paint²

50 years 18 years

40 years 18 years

30 years 15 years

20 years

Not recommended

15 years

Not recommended

  • This chart is a guide only and applies to roofing. Design, position and other factors can influence which product is recommended. For full details, including information on the environmental categories and applications like cladding and guttering, please visit colorsteel.co.nz/warranty.
    ¹ Against perforation as a result of corrosion. ² Covering the paint surface against flaking, peeling and excessive fade.

TECHNICAL ASSISTANCE Phone 0800 697 833 Email specifications@colorsteel.co.nz
TYPICAL DETAILS Available upon request from specifications@colorsteel.co.nz

10

COLORSTEEL DRIDEX®

11

NOTE: Buyers and users of New Zealand Steel Limited products and services must make their own assessment of the products for their own conditions. All queries regarding product specification, purpose or application should be directed to New Zealand Steel Limited, email specifications@colorsteel.co.nz. New Zealand Steel Limited reserves the right to modify products, techniques, equipment and statements to reflect improvements in the manufacture and application of its products. The information contained in this brochure is accurate as at July 2024 and supplied without prejudice to New Zealand Steel Limited’s standard terms and conditions of sale. In the event of conflict between this information and the standard terms and conditions, the standard terms and conditions prevail. This brochure supersedes all previous brochure editions. COLORSTEEL®, MaxamTM and Dridex® are registered trademarks of New Zealand Steel Limited. Copyright© New Zealand Steel Limited. July 2024. CSD03
COLORSTEEL.CO.NZ

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals