CareCo MS08090002 Mobility Scooter Alarm Instruction Manual
- June 12, 2024
- CareCo
Table of Contents
MS08090002 Mobility Scooter Alarm
Instruction Manual
MS08090002 Mobility Scooter Alarm
Triaxial Accelerometer Sensor, 7 Stages
Sensitivity for adjustment.
SOS Emergency Help Function, 6 Tones
Loud Siren Sound Selectable
3*AAA Batteries for Power Supply, Life
lasts for 6-10 months
| Waterproof: | P55 |
|---|---|
| Range: | 40-80M |
| Volume: | 13dB |
| Operating Temperature: | -20~60°c |
| Operating Humidity: | <80% |
| Storage Conditions: | -30~70°c |
Structure
Instructions
21 Method of loading & replacing battéries
2.1.1 Normally batteries are Loaded after production.
Occasionally, do s the below figure. Remove the screw from the bottom, and
then Load 3 pieces of AAA alkaline batteries, It is succeed if the alarm
sounds 3 beeps. Unload the batteries if won’t use the alarm for long time.
Remove the screw from the bottom, use triangle slice to apart the plate from cover from the bottom o sides.
2.2 Usages and Settings
2.2.1 ARM RDISARM Mode Setting
Press[ ] button on remote once, the alarm will sound “Do.Le.M”, then a beep
after 5s,it becomes ARM alert state If any vibration or movement detected, the
alarm will sound awarning beep for 25 in a certain tone, if triggering the
alarm again within 2-125, it will alarm for 305 in 6 ringtones automatically.
To stop the alarm or exit ARM mode, press [ ] button on remote once, it will
sound “Mi.Le..Do”
Sensitivity Adjustment
Stages from Do Le Mi Fa So La Si, defavlt sensitivity is Do (highest).
Adjustment way: press and hold [ ] alarm will sound “Me.Le..Do” for 2 or
3times when LED indicator goes off and display for a long pause then be
bright, loosen your finger then press [ ] button once it will sound Do Le
MiFa So La Si, then press [ ] button again once, you will hear “Do’, press
again “Le”etc.. from highest to lowest then sound in circulation Once any
sensitivity you need, just stop and press [ ] button to exit the setting
2.2.3 Select Tones
Press [ ] button to select tone, 6 tones in all (Invalid for ARM Mode)
2.2.4 Vehicle Finder function:
press [ ] button, it will sound certain tone you can set different tones by [
] button, vehicle finder tone is the same tone once you set by [ ] button
2.2.5 .3 Erase all remotes: Be caution for this operation. Keep the alarm in disarm mode Jong press [ ] button on paired remote, when LED indicator goes off and display for a long pause then be bright, after a beep ,press [ ] button, 3 beeps will erase all paired remotes .
2.2.6 SOS Function Setting
2.2.6.1 SOS function is off in default mode .Notification: SOS function
will recognize the installation status of alarm. Please do not change
direction after installation, or this function will be invalid.
2.2.6.2 Turn on SOS: Press and hold [ ] button, when LED indicator goes
off and display for a long pause then be bright, press [ ] button, the alarm
will sound a beep, then 5 beeps ,the function is on. If 2 long beeps, setting
is failure. ( keep the alarm still when setting )
2.2.6.3 Turn off SOS : press and hold [ Er ] button, when LED indicator
goes off and display for a long pause then be bright ,press [ ] button, then 2
long beeps will turn off the function. Next, press [ ] button to exit the
setting. Power off the alarm will turn off SOS function too.
2.2.6 .4 When the alarm is in disarm mode with SOS function on, tilt the
vehicle at 45 degree angle, it will sound SOS tone automatically, straighten
the vehicle will stop the sound .
2.2.7 Low Battery Indication
2.2.7.1 For alarm, please replace batteries in time if you hear
“Du..Du”when arming/disarming .
2.2.7.2 For remote, please replace battery if you notice that the LED
indicator goes dark or wireless range becomes shorter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>