NOVY 42110 Panorama 120 Pro 4 Zones Hob and Hood Instruction Manual
- June 12, 2024
- NOVY
Table of Contents
NOVY 42110 Panorama 120 Pro 4 Zones Hob and Hood Instruction Manual
GENERAL INFORMATION
General
These are the mounting instructions for the Novy hood shown on the cover. The
user manual is a separate booklet that is supplied with the hood. Carefully
read these instructions before installing and commissioning the hood.
A number of symbols are used in these mounting instructions. The meanings of
these symbols are given below.
Safety
Observe the following mounting and safety tips for mounting:
- The installation and electrical connection of the unit shall be carried out by an authorised expert.
- The manufacturer does not accept any responsibility for any damage resulting from faulty building in or connection.
- Check if all mounting materials have been supplied using the drawings on page 4.
- The unit is intended for household use only (preparation of food) excluding any other domestic, commercial or industrial use.
- Safety can only be guaranteed if the unit is connected to an earth wire in accordance with the required regulations.
- Do not use an extension cord for connecting to the electricity grid.
- Replace defective or damaged parts only with original Novy parts.
Important before mounting
Page 4 of these mounting instructions shows the mounting drawings. Observe the following mounting tips before starting the mounting activities:
- For easier mounting of the hood it is recommended to do this with at least 2 persons.
- The housing of the unit to be mounted has the right dimensions.
Make sure that the power circuit to which the unit is connected is switched off.
INSTALLATION
-
Make sure that the power circuit to which the unit is connected is switched off.
-
Check that all the hood accessories are present in the packaging.
-
Check that all the hood parts are present in the packaging.
Warning: pick up the hood only at the frontside to prevent glass damage of the hood. -
Check that all the hob parts are present in the packaging.
5a Built-in height G≥ 760mm surface mounting:
Make cut-out in bottom plate cabinet
5b Built-in height G≥ 760mm flushline mounting:
Make cut-out in bottom plate cabinet
6. Built-in height G < 760mm
When height cabinet + worktop < 760mm, a cut-out in the bottom plate of the
cabinet needs to be performed to install the cooker hood.
To install the cooker hood kit 1821.400 can be used. Follow the steps
described in the corresponding installation manual of the extension kit and
then continue back from step 8.
7. Measure the height left (Y1) and right (Y2) from the hob base plate to the
supporting surface.
Surface mount (L) = Top worktop surface.
Flush mount supporting (R) = Milled edge in worktop.
8. Set the height (Y) with the levelling feet, measure from the top surface
of the hood to the underside of the levelling feet. Measure the height (V)
from the underside of the hood to the underside of the levelling feet (needed
for vertical bend).
9. Secure the levelling feet with the wrench 17.
10. Measure the height (Q) from the base plate to the ground position.
11. Cut the vertical bends to size X = (V+Q) -5mm.
12. Slide the vertical bends into the outlet piece below the hood.
13. Make sure that the hood guides are fully inward and secure this position.
14. Lift the hood through the work top cut-out in the housing.
Warning: hold the hood only at the outside to prevent the glass
breaking.
Warning: this activity is best done by 2 people.
15. Place the positioning guides (42120035) between the worktop cut-out and
the hood. Position the side and rear edge of the hood against these two
guides.
16. Set the bolt to the centre of its range to make fine adjustment of the
hood possible later.
17. Slide the hood guides fully against the side wall of the housing.
Slide the mounting brackets between the bolt and the lock nut of the guide
until they are in the centre of the groove.
Secure this position with the screws supplied.
Perform this action on both the left and right.
18. Secure the position of the guides with the black screws
19. Level the hood at both the left and right by moving it forwards or
backwards at the bottom.
Use a short spirit level (≤ 30cm) and place this on the marked places.
20. Secure the position of both levelling feet in the housing with the plates
n° 1821043 and screws n° 1821153.
21. Adjust the position as necessary with the adjusting bolts on the guides.
The positioning guides must be positioned with minimal clearance between the
worktop cut-out and the hood.
22. Remove the positioning guides.
Warning: Carry out the following action carefully to avoid glass dammage.
23. Check the height of the cooker hood with a ruler, it MUST be levelled with the worktop (surface) or milled edge (flushline). Adjust if necessary with the levelling feet.
24. Apply the waterproof tape 2mm from the rim to the underside of the hob
glass.
If necessary, remove a central piece of the tape from the back of the
hob if it would not be completely flat at the back during installation.
25. Place the induction hob on the hood. Make sure the edge of the cut-out in
the induction hob glass is aligned with the side profiles of the tower.
Do not apply sealant between the bottom side of the hob and the worktop.
26. Carefully place the upper glass with the pins in the cut-outs provided in the hood.
Perform the above action carefully to prevent glass damage and scratches.
27. Surface mounting: Adjust the position of the induction hob until the
spacing around the tower top glass and cut-out is even.
Flushline mounting: Adjust the position (front, back, left and right) of
the cooker hood until the spacing around the tower top glass and cut-out is
even. (STEP 18, 21)
28. Secure the position of the hob on the hood with the 6 screws n° 1821247.
Tighten these bolts only finger tight, do not use a hand-held screwdriver.
29. 30. Adjust as necessary the height of the tower with respect to the top
of the hob.
Turn the bolt with a wrench 10 counterclockwise to raise the tower and
clockwise to lower it.
31. Connect first the hob cable connector to the hood.
32. Hood : connect the plug to the mains supply.
Hob : connect the hob’s power cable according to the relevant connection
diagram.
Optionally, the hob can be set with a power limit, see chapter “Power
limitation induction hob”.
33a Recirculation built-in box option: connect the in-built box to the
hood outlet, if necessary, use optional fittings.
33b Outlet with wall outlet grille option: use optional fittings to make
the connection with the duct work possible.
34. Switch the unit power supply circuit on.
35. Keep the knob pressed for 3 seconds.
If the 4 LEDs on the control flash directly, the safety system of the
tower is activated.
You can manually turn the tower up using a flat screwdriver.
Carefully remove the top glass from the tower and place the screwdriver
in the provided recess of the spindle in the centre of the tower.
Now turn the tower fully up until the safety switch as in step 36 is
visible.
36 The tower now moves to its highest position (30 cm).
37 Remove the safety sticker from the tower. The 4 LEDs on the controller
flash.
38 Slide both lower collection trays into the hood with the short side (K)
facing forward n° 42120039.
39 Place the collection security n° 42120026 in the hood. They should be
positioned against the center of the tower.
40. Slide both upper collection trays n° 1821107 into the hood.
41. Place both grease filters in the hood on the fall protection.
42. Verify the correct placement of the grease filters using the positioning
tab.
43. Place the front glass on the hood tower. Position the tabs of the glass
in the cut-out in the tower and tilt the glass toward the magnets until the
glass snaps into place.
44. Press the knob to re-initialise the tower.
45. The tower now moves to the closed position.
46. Recirculation : Device is set in recirculation mode by default.
Duct out: set device in duct out mode by pressing the key combination “+”
and “-” and during 3 seconds. The led next to will blink 3x to acknowledge the
setting. Repeat these actions for recirculation mode, the led will be on for 3
seconds.
47. OPTIONAL : Installation I/O module n° 990036 Remove the cover from
the connection connector.
48. Plug in the I/O module connection cable into the connector. (See manual
990036 I/O module)
POWER LIMITATION INDUCTION HOB
Power limitation induction hob
The hob is equipped with a power limitation. If the power level on two zones
exceeds the maximum power, the last selected cooking zone will be maintained,
and the other cooking zone will be automatically reduced.
The display of this zone will flash first, then the level is automatically
reduced to the highest appropriate position.
This restriction is set at the factory to 7400W (32A) on the 4 zones hob
reference 42110 and on 10400W (48A) for the 5 zones hob reference 42120.
This power limit can be adjusted if required.
Configuration procedure:
- Make sure there is no more pot on the hob
- Disconnect the appliance from the grid by removing the fuse or turning the circuit breaker off.
- Reconnect the table to the grid
- Start the procedure within 2 minutes after reconnecting the hob to the grid
- Make sure all cooking zones are off.
- Do not press on .
Novy nv reserves the right at any time and without reservation to change the structure and the prices of its products.
NOVY nv
Noordlaan 6
B – 8520 KUURNE
Tel. 056/36.51.00
Fax 056/35.32.51
E-mail: novy@novy.be
http://www.novy.be
France: Tél: 0320.940662
Deutschland und Österreich: Tel: +49 (0)511.54.20.771
Nederland: Tel.: +31 (0)88-0119110
United Kingdom: +44 (0)207 866 2493
España: Tel.: +34 938 700 895
Italia: Tel.: +39 039.20.57.501
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>