FOSSiBOT F3600 Portable Power Station User Manual

F3600
User Manual

Company official website: https://www.fossibot.com
Technical service email: support@fossibot.com

Precautions For Use

Please avoid long-term storage and use of this product in environments with high temperature and humidity or direct sunlight to avoid shortened battery life and other failures. The product should not be close to the fire source, otherwise it may cause a major fire or accident.
This product must not be disassembled or modified. Improper operation may cause product malfunction or even fire.
Be careful not to drop or drop the product from a high place, so as not to damage the product.
Please store or use this product out of the reach of children, otherwise the product may be dropped or collided and may cause bodily injury to children.
Please use our original accessories, and we will not guarantee the defec-tive products caused by the use of non-original accessories.
Please directly plug in the wall socket to charge the product, do not use extension cords or cable taps, otherwise there is a risk of damage to the extension cords and cable taps or even a fire; If the extension socket is plugged in to charge this product, please do not connect other electrical appliances to this socket, otherwise the household meter may trip.
When the product is not in use or idle, please turn it off and unplug the power cable.
If it needs to be idle for a long time, please consume the product from a fully charged state to an uncharged state, then recharge it to about 50% of the battery level and store it. In order to prolong the life of the product, please take three months as a cycle, operate and keep it in this way.
If the product reaches scrap conditions, please discard or recycle the product in accordance with local laws.

Packing list

Product Introduction

This product is a portable power station with a built-in battery pack with charge/discharge function. It includes both AC output interface and DC output interface such as USB output, cigarette lighter output, DC output, etc. It also has functions such as display, interface control, protection, and alarm. Moreover, this product can be charged by AC mains, solar panels and vehicle charging.
The following are the main features of this product:

• Equipped with EVE brand LiFePO4 battery, the battery capacity is as high as 3840Wh, and the safety level is extremely high.
• Pure sine wave AC output can meet almost all daily electronic equipment and small household appliances.
• Two-way fast charging technology is adopted to fully charge the product within 2 hours.
• A great variety of output interfaces such as USB-A, Type-C PD3.0, DC5521, XT60, cigarette lighter output, etc., meet many different application scenarios.
•  In UPS mode, the switchover time is less than 10ms which is truly seamless switching.
• Multiple protection mechanisms such as battery, circuit, structure, etc., guarantee the product safety.

Button Function Introduction

1. Power ON/OFF Button

2. USB ON/OFF Button

3. LED Light Button (switch to different mode)

4. DC ON/OFF Button

5. LCD Screen

6. Input Power Knob

7. Cooling Air Duct

8. AC Button (manually switch to 50/60Hz)

9. XT90 Input Port ( for solar panel)

10. AC input

11. Overload Protection Button

12. Removable Flashlight

13. Power ON/OFF Button
    Instructions: Press and hold the power button for 3s to turn on/off the whole system.

14. USB ON/OFF Button
    Instructions: Short press the USB button to turn on the USB output ports, and short press it again to turn them off.

15.  Light Button
    Instructions: Short press the LIGHT button, the LED light is on; short press it again, the LED light enters the SOS mode, short press in turn, enters the strobe mode, and finally the LED light is turned off (LED light in any mode, long press the LIGHT button for ? 1 second , directly turn it off ).

16. DC ON/OFF Button
    Instructions: Short press the DC button to turn on the DC output ports, and short press it again to turn them off.

17.  LCD Screen
    Display the product’s battery level and usage status tips.

18. Input Power Knob
    When the product is connected to the AC mains for charging, the power is adjusted according to the actual input voltage. The clockwise rotation increases the input power, and the counter clockwise rotation decreases the input power. It is worth noting that charging this product at low power is beneficial for extending battery life.

19. Cooling Suction/Exhaust Port
    When the product reaches the temperature threshold set by the system, the cooling fan will automatically run, accompanied by a certain fan noise. Do not block the cooling suction/exhaust port during use of this product, and do not place any object within the range of 30CM.

20. AC Button
    AC control (AC output*3, rated power 3600W) Operation: short press to switch on/off.
    Note:
    1. Please confirm the output voltage and frequency before use.
    2. Press the button for 2 seconds to enter the frequency change mode and 50Hz and 60Hz will flash on the display. Press the key again, to select the correct frequency and then wait until the frequency light stops blinking and you get the desired frequency. 3. Short press 10 times to switch voltage to 220V or 230V.

21. 90 Port (Solar Panel Input)
    This interface supports solar panel input or car charger input. For details, please refer to “Solar Panel Connection” on page 8 of this manual and “CarNehicle Charging” on page 9.

22. AC Input
    Charging the product by a household socket can achieve 2200W fast charging. It only takes 2 hours to fully charge from 0 to 100%. When charging in this way, please pay attention to the following points:
    Please directly plug in the wall socket to charge the product, do not use extension cords or cable taps, otherwise there is a risk of damage to the extension cords and cable taps or even a fire.
    If the extension socket is plugged in to charge this product, please do not connect other electrical appliances to this socket, otherwise the household meter may trip.

23.  Overload Protection Button
    When the power supply current is unstable due to lightning or other reasons, and there is a large current input at the AC Input, in order to protect the product, the overload protection function (safety circuit breaker) will activate and cut off the AC input port. Please follow the sequence below to restore the AC input function: 1) Tum off the power button and unplug all ports. 2) After confirming that there is no abnormality in each part, turn on the power button. 3) Press the overload protection button, connect the AC Cable to restore the AC input.

24. Removable Flashlight Torch
    This flashlight torch can be removed from the power station and work as a portable torch. For detailed specifications, please refer to the Flashlight Torch User Manual.

Introduction of Display Interface

1 Remain Using/ Recharging Time
2 Fan Status
3 High/Low Temperature Protection
4 Battery Level Percentage| 5 Input Power in Total
6 Output Power in Total
7 LED Light ® AC Output| 8 Type-C
9 USB-A QC3.0
10 Connected to the AC Mains
11 XT90 Port| 12 DC (12V) Output
13 Cigar Lighter (12V) Output
15 XT60 (12V) Output
16 Battery Progress Bar
---|---|---|---

Screen Display Description
Power display: When the product is in the charging state, the battery progress bar rotates continuously in the form of a clockwise marquee, and the battery level percentage gradually increases; when the prod-uct battery level is 0, the battery level percentage icon flashes. Input and output status: When the product is working, the total input power, total output power and the cursor corresponding to the working area will be displayed on the screen. Alarm prompt: See the following troubleshooting table for details.

Troubleshooting Sheet

the switch in the area corresponding to the icon to remove the alarm.
The temperature warning
icon flashes and beeps.| The temperature of the prod -uct is too high or too low.| Take the product out of the charging state remove all loads, turn the power off, wait for the device to reach a suitable working temperature, then the alarm is removed.
The icon of connecting to the AC mains flashes and the product cannot be charged.| The charging cable is poorly connected.| Veify the connection status of the cable and the power supply.

UPS Mode

• UPS Feature
  This product has the function of backup uninterruptible power supply. The usage and operation precautions are as follows: As shown in Pic 1 below, when the product is connected between the wall socket and the electrical appliance, and the power supply and AC switch of the product are in the ON state, the product enters the UPS working mode. The AC mains in the socket supplies power to the electrical appliance through the bypass circuit, and also charges the product. In this working state, the rated power of the electrical appliance must be lower than 2500W, otherwise overload protection may be triggered.

As shown in Pic 2 below, when the AC mains at the socket end is disconnected, the bypass output inside the product stops working, the product switches to a bidirectional inverter circuit within 10ms, and the circuit outputs supply power to the electrical appliance to ensure that the electrical appliance is uninterrupted and works normally during the process.

Connection of Solar Panels

Under the condition of sunlight, this product can be connected to the solar panel and getting charged. The charging power is determined according to the conditions of sunlight and weather. In this charging mode, we support solar panel input within 2000W, and the input voltage cannot exceed 160V, otherwise the product abnormality caused by it will not be covered by the warranty.
We recommend the following two charging schemes:

• Solar panel charging

Scheme one
Portable Power Station Charging Area

Scheme two
Portable Power Station Charging Area

Car/Vehicle Charging

When the car is in the process of starting, connect the car charging port on the car and the product through the car charging cable to charge the product. The connection method is shown in the picture below: This product supports 12V/24V car charger charging, please pay attention to the following two points when using this method to charge:
Please do it when the car started, otherwise the car battery may be exhausted.
Vehicle charging power is usually in the range of 90W-120W or 200W-240W, and the charging time is long. If fast charging is required, the AC mains charging is recommend-ed.

Product Specifications

overload, short circuit protection
USB-A Output| QC3.0 18W X2
Type-C 0 Output| PD2OW X3
Type-C 0 Output| PD100W Max.
DC 5521| 12V/3A X2
XT-60 Output| 12V/25A
Cigarette Lighter Output| 12V/10A
Shutdown Current| < 500uA
Working Temperature| -10∼40 ° C
Environment Humidity| 590%RH
Cycle Times| 6500+ times**

Battery Specifications

Disclaimer

Before use, please read the user manual of this product to ensure full understanding and correct use. After reading, keep the user manual properly for future reference. If you do not operate this product correct- ly, you could cause serious injury to yourself or others, or result in damage to the product and property. Once you use this product, you are deemed to have understood, recognized and accepted all terms and content of this document. Users undertake to be responsible for their own actions and all consequences arising therefrom. We are not responsible for all losses caused by the user’s failure to use the product in accordance with the User Manual.
In compliance with the law, the company has the final right to interpret this document and all related documents of the product. If it is updated, revised or terminated without prior notice, please visit our official web- site for the latest product information.

Warranty

Warranty

Product Model|
User Name|
Address|
Phone Number|
Email|
Sales Contact|
Purchasing Date|
Please fill in all of the above items.

This product comes with a 24-month warranty from the date of purchase

•  If there is a quality problem within the scope of normal use, we provide warranty.
• After purchasing our company’s products, please keep this product together with invoices and other items, and please provide information according to our company’s reliance request when maintenance services are required.
• Warranty service may not be provided if the warranty card is damaged, altered, etc., and it is considered to be incorrect, or if the warranty card is not stamped by the store where it was sold.
•  Damage caused by use beyond the normal use range is not covered by the warranty service.
• The content of the warranty scope is subject to the content recognized by the company.
• Even within the scope of the warranty, there are times when an equivalent product can be exchanged. Shipping and maintenance costs for products not covered by the warranty shall be borne by the customer.
• Product specifications and features are sometimes changed without prior notice.
• Please refer to our updated guideline on our website below.
  Manufacturer: Shenzhen Qichang Intelligent Technology Co., Ltd.
  Address: Room 510, 5th Floor, Bld 7, Yunli Smart Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China
  Technical service email: support@fossibot.com
  Company official website: https://www.fossibot.com

https://eulossibot.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>