Specialized SPEEDZONE II-Bike Computer User Manual
- June 12, 2024
- SPECIALIZED
Table of Contents
Specialized SPEED ZONE II-Bike Computer User Manual
INSTALLATION
- Remove the components from the side of the handlebar intended for the installation of the display mount.
- Fig. 1: Install the display mount and rotate it into position A.
- Tighten until the mount does not slip easily B . Do not overtighten. Recommended torque is 4.4 in-lbf / 0.5 N.
- To install the display, position sideways C then rotate 90° D.
BATTERY REPLACEMENT
- Fig 2: Use a very small flathead screwdriver to lift up the edge of the battery cap, then gently lift the battery out of the cap.
- Fig 3: Replace the display unit battery with a new CR 2032 coin cell battery, and place the new battery into the cap with the text facing inside the cap E . Make sure the seal is not damaged and press the cap back in, making sure the tab of the lid is first aligned with the recess on the display F.
- When the battery is replaced, all information stored on the display (odometer, timer) is erased. If desired, take note of the information before replacing the battery.
- Fig 3: The sensor uses a 23A battery G . To access the battery, rotate the cap using a coin or flathead screwdriver.
DISPLAY FEATURES
MAIN SCREENS
- The battery icon turns on (coin cell battery low).
- No Signal or key for 30 min.
- Clear function data (hold the left button for 2 seconds).
- Show odometer data (hold the right button for 2 seconds).
Wake from shipping mode: After removing the display from the packaging, press and hold the left and right buttons for two (2) seconds to wake up the display for the first time.
LEGEND
SPEED SENSOR INSTALLATION
L Adjust the magnet position so the magnet is aligned with the line on the
bottom of the edge of the sensor. Position with 1/32 – 1/8 in (1-3mm) of
separation. DO NOT overtighten the magnet.
M The sensor should be mounted with the battery door cap toward the ground,
with no more than 24” (in) / 600mm distance between the sensor and the
handlebar.
DEFAULT PAGE SETTINGS/NAVIGATION
- There are 4 preset pages, each of which displays a different combination of information.
- The pages can be navigated using the left/right buttons.
- To clear the Distance, Average speed, Timer, and Max speed data, press the left button for two (2) seconds.
SYSTEM SETUP
SYSTEM SETUP
- Choose the desired time O (12 or 24 hours), hour P, and minute Q.
- Set the units R (km/h or mph).
- Set the wheel S and tire T size (preset or custom).
- If your wheel/tire size is not listed or you want to guarantee the closest accuracy, measure your wheel circumference U (one full rotation of a wheel, using the valve stem V as a marker).
GENERAL INFO
CLEANING/CARE:
- Do not expose the display to intense heat or sunlight for a prolonged period of time. This can damage the display and/or battery.
- Only use a damp or dry soft cloth to clean the display. Do not use harsh cleaning products.
- Do not disassemble or drop the display.
- Make sure the display and mount are firmly installed on the handlebar before riding.
DISPOSAL
Batteries and chargers must not be disposed of in your household trash! All
batteries and chargers must be disposed of in an environmentally friendly
manner, in accordance with the battery disposal regulations in your country or
state. Ask your Authorized Specialized Retailer for information about how to
dispose of a battery or charger and any applicable take-back program.
REGULATORY STATEMENTS
RoHS: Specialized Bicycle Components, Inc. certifies that this product and its
packaging are in compliance with European Union Directive 2011/65/EU on the
Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronics Equipment, commonly known as RoHS. FCC Statement: This device
complies with part 15 of the FCC Rules. Caution: If any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference and (2) it must accept any interference received, including
interference that may cause undesired operation. This grantee is not
responsible for any changes or modifications not expressly approved by the
party responsible for compliance. Such modifications could void the user’s
authority to operate the equipment. The RF Exposure Compliance distance is 20
millimeters.
NOTE : This equipment has been tested and found to comply with limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in
residential installations. This equipment generates, uses, and can radiate
radio frequency energy, and if not# installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio or television
equipment reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SYSTEM SETUP (custom tire size)
When selecting the custom (CUST) W option from the wheel diameter options, Data Field 2 will flash. Enter the tire circumference size in millimeters. To scroll quickly, press and hold the left button to scroll down or the right button to scroll up.
ISED Canada Statement: This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device. CAN ICES-3(B)/NMB-3(B). The device meets the exemption from the
routine evaluation limits in section 2.5 of RSS 102 and compliance with
RSS-102 RF exposure, users can obtain Canadian information on RF exposure and
compliance. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This equipment should be
installed and operated with a minimum distance of 20 millimeters between the
radiator and your body
FUNCTION OPTIONS / SPECIFICATIONS
FUNCTION OPTIONS / SPECIFICATIONS
DATA FIELD 1 & 2
KPH/MPH| Speed| 0.0 – 99.9 kph / mph
AVG| Average Speed| 0.0 – 99.9 kph / mph
DIST| Distance| 0.0 – 999.9 km/mi
TIMER| Trip Time| 0:00” – 59:59” (second)
01:00’ – 99.59’ (minute)
MAX| Max Speed| 0.0 – 99.9 kph / mph
ODO| Odometer| 0.0 – 9999 km/mi/
DISPLAY
Clock| 00:00 – 23:59 (24hr) / 12:00 – 11:59 (12hr)
Auto sleep / Auto wake| 30 minutes / < 8 seconds
Battery type| Coin Cell 2032
Dimensions| 62mm x 46mm x 14mm
Operating temperature| -10° C — +60° C / +14° F — +140° F
Water/dust protection| IP67 (< 1 meter for 30 minutes)
Operating Frequency| 120 KHz
Max. Power| < 0.1 mW
ODOMETER SETUP
- After replacing the battery, the odometer can be set manually X , separately from the system setup.
- Press the right button for four (4) seconds, set the first digit, then press the left and right buttons together to move to the next digit and set it. Repeat for all four digits until the odometer is set.
SPECIALIZED BICYCLE COMPONENTS
15130 Concord Circle, Morgan Hill, CA 95037
408-779-6229 0000133769_UM_R4, 09/19 We
may occasionally issue updates and addendums to this document. Please
periodically check www.specialized.com or
contact Rider Care to make sure you have the latest information. Info:
ridercare@specialized.com /
877-808-8154
Download PDF:Specialized SPEED ZONE II-Bike Computer User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>