PELOTON PL-01 Home Exercise Bike User Guide

June 12, 2024
Peloton

PELOTON logo

BIKE HOME ASSEMBLY GUIDE

WARNINGS AND SAFETY INSTRUCTIONS

Read all warnings and instructions before beginning to assemble the Peloton Bike. Assemble the Bike according to the procedures described in this guide. Peloton is not responsible for damage, injury, or equipment failure caused by improper assembly or use.

Keep children and pets away from the Bike at all times.

The Bike and Bike package are extremely heavy and require more than one person to lift or carry. Lifting heavy objects can cause muscle strain and back injuries. Use lifting aids and proper lifting techniques when moving or assembling the Peloton Bike.

Perform a complete visual inspection of the Peloton Bike and test all features and functions prior to use.

It is the owner’s responsibility to ensure that all users are aware of all warnings and precautions. Read the Peloton Bike User Manual for full safety information and usage instructions before operating the Bike, and use only as described.

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

GETTING READY

A Touchscreen
B Handlebars
C Handlebar Post
D Resistance Knob / Emergency Brake
E Handlebar Height L-Handle
F Water Bottle Holder
G Flywheel
H Wheels
I Front Stabilizer
J Power Supply
K Pedals
L Rear Stabilizer
M Leveling Feet
N Crank Arms
O Seat Height L-Handle
P Seat Depth L-Handle
Q Weight Holders
R Saddle

PELOTON PL-01 -Features

PELOTON PL-01 - QR Code 1

VIDEO INSTRUCTIONS

Scan the QR code or go to onepeloton.com/setup/bike to access assembly video and instructions online.

PREPARE YOUR WORKSPACE

CAUTION: The Bike and Bike package are extremely heavy and require more than one person to lift or carry.

  • Find a location for your Bike. Peloton recommends assembling the Bike on a solid, level surface in the same space where it will be used, to limit movement after assembly. Refer to the Bike User Manual for location requirements.
  • Clear a 5 ft by 5 ft space for assembly.
  • Locate a pair of scissors or a similar tool. The Bike includes all the tools you will need for assembly, but you will need scissors to unpack it.
  • If you can, have somebody available to help you. A second person isn’t required for assembly, but can make some steps easier.

PELOTON PL-01 - PREPARE YOUR WORKSPACE

  1. The power cord should be able to reach an outlet without passing under the Bike.
  2. A mat helps protect your Bike and floor
  • There should be 24 in of empty space on each side of the bike.
UNPACK YOUR BIKE

1 Open the outer carton. Inside, find the inner bike carton, the home assembly kit, and the touchscreen box. Clear away the rest of the cardboard, but leave the unfolded outer carton under the Bike–it will protect the Bike and your floor during the assembly process.

PELOTON PL-01 - UNPACK YOUR BIKE 1

  1. BIKE CARTON
    BOX A
    BOX B
    BOX C

  2. HOME ASSEMBLY KIT

  3. TOUCHSCREEN BOX

  4. OUTER CARTON

2 Using a pair of scissors, cut the (3) plastic straps on the inner carton.

3 Lift the carton lid off the base. It should slide off easily.

4 Find and set aside boxes A, B and C.

5 Clip the zip ties on the frame and remove the handlebars and monitor arm.

6 Remove the remaining packaging materials from the carton.

BIKE CARTON

Bike Frame
PELOTON PL-01 - BIKE CARTON 1

Handlebars                                 Monitor Arm

Box B                                                  Box A
PELOTON PL-01 - BIKE CARTON 4

Box C

IDENTIFY PARTS

Before beginning to assemble your Bike, locate and identify all parts and tools.

HOME ASSEMBLY KIT

Bike Assembly Guide         Cardboard Stabilizer Insert

Long Allen Wrenches                 Pedal Wrench
3mm               5mm

BAG 1                                      BAG 2

BOX A

Front Stabilizer
PELOTON PL-01 - BOX A1

Weight Holders
LEFT                   RIGHT

Bolt G          Washer H            Washer I

4x                   4x                  4x

BOX B

Rear Stabilizer
PELOTON PL-01 - BOX B1

Weight Holders

BOX C

Pedals
LEFT                          RIGHT
           

Water Bottle Holders
PELOTON PL-01 - BOX C3

Allen Wrenches
3mm                4mm                5mm


Large Hardware Bag*          Velcro Strap


Hexagon Multitool        15 mm Combination Wrench


6mm Allen Wrench and Phillips head screwdriver

  • The large hardware bag in Box C contains the same bolts and washers as hardware bags 1 & 2.
    You shouldn’t need it to assemble your Bike, but if you need a spare bolt or washer, you can find it here.
TOUCHSCREEN BOX

Touchscreen                              Touchscreen hardware bag
PELOTON PL-01 - TOUCHSCREEN BOX 1 Bolt J  4x

Power Supply

ASSEMBLING THE BIKE
REMOVING THE BIKE FROM THE CARTON

1 Make sure the L-handles at the front of the Bike and seat tube point straight down. If either L-handle sticks out sideways, pull the handle out and rotate it to point down.

PELOTON PL-01 - ASSEMBLING THE BIKE 1

2 Fit the cardboard stabilizer insert onto the frame as shown. Make sure it sits flush against the flywheel.

PARTS AND TOOLS

CAUTION: Lifting heavy objects can cause muscle strain and back injuries. Use lifting aids and proper lifting techniques when moving or assembling the Peloton Bike. A second person may be helpful when raising and lowering the Bike.

3 Slowly lower the Bike onto its left side. Make sure the stabilizer insert stays in place.

PELOTON PL-01 - ASSEMBLING THE BIKE 3

4 Remove the carton base from the bottom of the Bike.

ADDING THE STABILIZERS

1 Fit the front stabilizer tightly against the front foot of the Bike.

Note: Make sure you have the correct stabilizer. The front stabilizer has wheels and the rear stabilizer does not.

2 Using the 6mm Allen wrench and (4) bolts A , secure the front stabilizer to the foot of the Bike. Make sure you fully tighten all four bolts.

PELOTON PL-01 - ASSEMBLING THE BIKE 4

3 Fit the rear stabilizer onto the back foot of the Bike.

4 Using the 6mm Allen wrench and (4) bolts A , secure the back stabilizer to the foot of the Bike. Make sure you fully tighten all four bolts.

CAUTION:  Make sure all bolts are tight before moving to the next step. Shake each stabilizer to make sure it is held securely against the frame. If there is any movement, tighten each bolt again.

5 Carefully lift the Bike and set it upright.

PARTS AND TOOLS

PELOTON PL-01 - BOX A1

A ×4         6mm

PELOTON PL-01 - BOX B1

A ×4         6mm

ASSEMBLING THE HANDLEBARS

1 Fit the handlebar post onto the handlebar base. Make sure the letters on the post will be upright when the handlebars are right-side up.

2 Add two washers C and two bolts B to the front of the handlebar base. Screw them in using your 5mm Allen wrench.

3 Add two flat washers C and two bolts D to the sides of the handlebar base. Screw them in using the 5mm Allen wrench.

PELOTON PL-01 - ASSEMBLING THE BIKE 5

4 Loosen the L-handle at the front of the Bike by turning it counterclockwise. Insert the handlebar post into the head tube and move it to its lowest position–you’ll need access to the bottom of the post.

PARTS AND TOOLS

B ×2        C ×2

****5mm

D ×2        C ×2

****5mm

Having trouble inserting the handlebar post?

A plastic clip inside the head tube may be getting in the way. Reach into the head tube and press both sides of the clip flat.

PELOTON PL-01 - ASSEMBLING THE BIKE 7

  1. HEAD TUBE TOP VIEW
  2. Plastic clip

5 Add bolt E to the end of the handlebar post. Screw it in using a Phillips head screwdriver.

6 Tighten the L-handle and wiggle the handlebars. Any movement could mean that the bolts aren’t fully tight. Then move the handlebars to the highest position and perform the same check.

CAUTION:  Make sure all bolts are tight before moving to the next step. If there is any movement when you wiggle the handlebars, tighten each bolt again.

PARTS AND TOOLS

E ×1        Phillips

ADDING THE WATER BOTTLE HOLDERS

1 Fit one water bottle holder against the side of the front shroud. *** Attach it using two bolts F** and the long 3mm Allen wrench from the Home Assembly Kit. Fit the Allen wrench through the outer openings in the water bottle holder for easier access to the bolts.

PELOTON PL-01 - ASSEMBLING THE BIKE 9

2 Using the remaining two bolts F , attach the second water bottle holder to the other side of the shroud.

***** The two water bottle holders are identical, so you can use either one on either side of the Bike.

PARTS AND TOOLS

       F ×2

Long 3mm

       F ×2

Long 3mm

INSTALLING THE PEDALS

CAUTION: Identify the right and left pedals before beginning installation. Make sure each pedal is correctly threaded before screwing it in. Misaligning the threads or turning a pedal in the wrong direction could lead to injury and damage the pedal and Bike.

LEFT                      RIGHT

1 Rotate the crank arms until both are parallel with the floor. Then turn the resistance knob all the way clockwise to lock the flywheel.

2 Screw in the right pedal. You may need to turn it slightly counterclockwise to seat it. Then hold the pedal steady and turn the axle clockwise to tighten it.

3 Screw in the left pedal. You may need to turn it slightly clockwise to seat it. Then hold the pedal steady and turn the axle counterclockwise to tighten it.

PELOTON PL-01 - ASSEMBLING THE BIKE 11

4 Once both pedals are hand-tight, use your pedal wrench to fully tighten them. Remember to turn the wrench toward the front of the Bike on both sides.

PELOTON PL-01 - ASSEMBLING THE BIKE 12

PARTS AND TOOLS

RIGHT

NOTE: The pedals are marked R and L for right and left. Make sure you know which one is which. The left pedal is reverse-threaded, so both pedals tighten when turned towards the front of the Bike.

    LEFT

ADDING THE WEIGHT HOLDERS

1 Make sure the L-handle under the seat points straight down. If it’s pointed up, pull the handle out and rotate it to point down.

2 Locate the (4) bolts G , (4) flat washers H , and (4) spring washers I. Add one spring washer and one flat washer to each bolt.

PELOTON PL-01 - ASSEMBLING THE BIKE 13

3 Identify the left and right weight holders. Hold the right weight holder against the right side of the seat slider and secure it using your 4mm Allen wrench and two bolts with washers.

PELOTON PL-01 - ASSEMBLING THE BIKE 14

4 Add the left weight holder to the left side of the seat slider using the remaining two bolts with washers.

5 Check both weight holders to make sure that all bolts are tight and both weight holders are firmly attached to the seat slider.

PARTS AND TOOLS

G ×4            H ×4

I ×4

R

L

ATTACHING THE TOUCHSCREEN

1 Carefully lay the touchscreen face down on a towel or mat. Remove the square panel from the back of the touchscreen.

PELOTON PL-01 - ASSEMBLING THE BIKE 15

2 Set the mounting plate perpendicular to the monitor arm.

PELOTON PL-01 - ASSEMBLING THE BIKE 16

PARTS AND TOOLS

3 Align the plate with the screw holes on the back of the touchscreen. Secure the touchscreen to the monitor arm using your Phillips head screwdriver and (4) bolts J.

PELOTON PL-01 - ASSEMBLING THE BIKE 17

Having trouble turning the mounting plate?

  • Snap the plastic caps off the mounting plate hinge.
  • Use the hexagon multitool to hold the nut in place. Then use the 6 mm Allen wrench to rotate the bolt about one half-turn counterclockwise.
  • Test the hinge again. You should be able to move it, but it should still be stiff enough to hold the weight of the monitor without moving. If you’re still having trouble moving it, continue to loosen in half-turn increments.
  • When you’re done, snap the plastic caps onto the hinge again.

PARTS AND TOOLS

        J ×4

Phillips

4 Snap the square panel back onto the touchscreen.

5 Insert the monitor arm into the handlebar base. Push it in as far as it will go and make sure the touchscreen is fully upright.

PELOTON PL-01 - ASSEMBLING THE BIKE 18

6 Tighten the bolt at the side of the handlebar base using your 6mm Allen wrench.

CAUTION: Make sure all bolts are tight before moving to the next step. Tilt the touchscreen forward and back to check for wobble between the touchscreen and mounting plate. If there is any movement, tighten each bolt again.

PARTS AND TOOLS

6mm

CONNECTING THE TOUCHSCREEN

1 Open the plastic clamp at the back of the touchscreen. This may require some force.

2 Locate the monitor cable at the left of the flywheel. Plug the cable connectors into the power and data ports. Make sure both connectors are fully seated, then close the clamp.

  1. POWER
  2. DATA

3 Using the velcro strap, secure the cable to the monitor arm. Make sure there is enough slack on both sides of the strap to raise the handlebars to their highest position and to tilt the touchscreen up and down.

PELOTON PL-01 - ASSEMBLING THE BIKE 20

CAUTION: Make sure that the monitor cable sits clear of the flywheel and brake assembly. Contact with moving parts could damage the cable.

PARTS AND TOOLS

LEVELING THE BIKE

1 Gently push the seat and handlebars from side to side to check if the bike rocks or wobbles.

2 If there is any wobble, check each of the four leveling feet. If any foot does not rest firmly against the floor, turn it clockwise to lower it. Note that the center foot on each stabilizer cannot be adjusted.

PELOTON PL-01 - ASSEMBLING THE BIKE 21

3 Using the 15 mm wrench, tighten the nut on each leveling foot. The nut should sit against the underside of the stabilizer.

PLEASE SEE THE PELOTON BIKE USER MANUAL FOR NEXT STEPS, INCLUDING PLUGGING IN THE POWER CORD, ADJUSTING THE BIKE TO FIT YOUR BODY, AND CONNECTING YOUR PELOTON ACCOUNT.

PARTS AND TOOLS

© Peloton 2022, Peloton Interactive, Inc. All rights reserved.

onepeloton.com

PL-01 | 40008795-B

Documents / Resources

| PELOTON PL-01 Home Exercise Bike [pdf] User Guide
PL-01, PL-01 Home Exercise Bike, Home Exercise Bike, Exercise Bike, Bike
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals