virtufit VFWALP100 Walkingpad 100 User Manual
- June 12, 2024
- virtufit
Table of Contents
virtufit VFWALP100 Walkingpad 100
Product Information
- Product Name: Walkingpad 100
- Model Number: VFWALP100
- Manufacturer: VirtuFit
- Website: www.virtufit.com
- Serial Number: SERIENUMMER SERIENNUMMER NUMERO DE SERIE
SAFETY INSTRUCTIONS
WARNING! Consult your doctor before you start exercising. This is particularly important for people with health problems. Please read all instructions before using the machine. VirtuFit assumes no responsibility for injury or property damage resulting from the use of this equipment. Please read this manual carefully before assembling and/or using the machine.
- Make sure that the machine is properly assembled and that all nuts and bolts are tight before using it.
- Lubricate all moving parts annually with petroleum jelly (acid- free) or silicone spray.
- Do not wear loose clothing to avoid getting caught in moving parts.
- Install and use the unit on a solid, level surface.
- Always wear clean sports shoes when using the appliance.
- Keep children and pets away from the appliance when in use.
- Maintain your balance when using the device.
- Do not place your fingers or other objects in the moving parts.
- Before exercising, consult your physician to determine the appropriate frequency, duration and intensity of exercise for your age and physical condition. Stop exercising immediately if you experience nausea, shortness of breath, fainting, headache, chest pain, tightness or any other discomfort.
- Do not hold the machine by the seat when moving.
- This machine should only be used by one person at a time.
- This machine is designed for domestic use and the maximum user weight is 100 kg.
- Leave 1-2 metres of space behind the machine to avoid accidents.
- Place the machine on a clean, flat surface. Do not place it on a thick carpet, as this may hinder the ventilation of the machine. Do not place the machine outdoors or near water.
- Keep the storage area dry, clean and level to prevent damage. Do not use the device for any purpose other than training.
- Use the device only in an environment where the ambient temperature is between 10°C and 35°C. Store the device only in an environment where the temperature is between 5°C and 45°C.
GUARANTEE
Warranty claims are excluded if the cause of the defect is the result of:
- Maintenance and repair work not carried out by an official dealer.
- Improper use, negligence and/or poor maintenance.
- Failure to maintain the appliance in accordance with the manufacturer’s instructions.
ADJUSTING
Adjusting the running belt
- The treadmill veers to the left: Turn on the treadmill, set the speed to 2 to 3 km/h without forcing. Use the Allen key to turn the screw on the left side of the end of the treadmill a quarter turn to the right (1). Run the treadmill for 1 to 2 minutes without a load. Repeat the process until the treadmill is exactly in the middle.
- The treadmill turns to the right: start the treadmill, set the speed to 2 to 3 km/h without a load on the treadmill. Using the hexagonal key, turn the screw on the right side of the end of the treadmill a quarter turn to the right (2). Run the treadmill for 1 to 2 minutes without a load.
- The treadmill has jammed: Use the Allen spanner to turn the screw on the right side of the end half a turn to the right and the screw on the left side of the end half a turn a to the right as well. Repeat the process until the blockage is resolved (3).
MAINTENANCE
Safe and efficient use can only be achieved if the appliance is properly installed and maintained. It is your responsibility to ensure that the appliance is maintained regularly. Parts that have been used and/or damaged must be replaced before the appliance is used again. The appliance should only be used and stored indoors. Long-term exposure to weather and temperature/humidity changes can have a serious impact on the electrical components and moving parts of the unit. Always unplug the power cord from the unit before cleaning or servicing it.
Daily maintenance
- Clean and remove sweat and moisture after each use.
- Check that the unit is free of dust and dirt.
- Do not use aggressive cleaning agents and keep the device away from moisture.
Semi-annual maintenance
- Inspect all bolts and nuts connected to the moving parts of the unit. Tighten bolts and nuts as necessary and appropriate.
- Check the mobility of moving parts and components of the unit. Use silicone spray if necessary and appropriate.
We recommend the following:
- Clean the unit after use.
- Use a dry cloth to clean the control panel and the areas around the on/off switch.
- Use a soft, clean cloth and detergent to remove stubborn marks and dirt from the unit.
- Store the unit in a safe, dry place away from heat and water.
- Repairs must be carried out by a professional technician, unless otherwise specified by the supplier or manufacturer.
- To avoid slipping during exercise, the treadmill belt should not be too loose. To avoid abrasion between the roller and the treadmill and to ensure proper operation of the machine, the treadmill should not be too tight. The distance between the step and the belt can be adjusted. The distance between the step and the belt should be 50 to 75 mm on both sides.
Cleaning
General cleaning of the unit will extend its life. Keep the appliance clean
by dusting it regularly. Regular maintenance will prolong the life of your
appliance and prevent injuries! For more information, please visit
https://www.virtufit.nl/service/faq/
CAUTION! Wear clean shoes to reduce the risk of soiling the machine. At least once a year, remove the cover to remove dust.
LUBRICATING THE TREADMILL
The treadmill is equipped with a low-maintenance, pre-lubricated treadmill. Wear and tear on the treadmill plays an important role in the operation and life of the treadmill, so it should be lubricated periodically. We recommend that you inspect the belt regularly. Contact us as soon as you notice any damage to the treadmill.
Recommended lubrication of the treadmill
- Low usage (less than 3 hours per week): once a year.
- Medium use (3 to 5 hours per week): every six months.
- Heavy use (more than 5 hours per week): every three months.
As a general rule: Lubricate if the mat appears dry. If in doubt, contact the manufacturer. The use of Vaseline (acid-free) or silicone oil is recommended for lubricating the treadmill.
Instruction
- Lift the mat.
- Apply two to three drops of silicone oil along the length of the treadmill.
- Turn on the treadmill and run for three minutes without stressing the treadmill (i.e. without standing on the treadmill).
CAUTION! Regular maintenance will extend the life of the treadmill and prevent injury!
TROUBLESHOOTING
- The display does not show any values: Check that the sensor and console cables are properly attached and undamaged. If this does not solve the problem, carefully bend the sensor.
- The device squeaks: Check that all bolts and nuts are tight. If necessary. No power: Check that all cables are connected.
- Motor failure: Check that the motor needs to be replaced.
- Power failure: Check that the sensor cable is properly connected.
- Safety Key does not work properly: Check that the safety key is properly attached.
ERROR CODES
- Err(or E00): Security key is missing from the panel or is not properly attached.
- Solution: Attach the security key to the yellow part of the panel.
- E2: Control board is broken.
- Solution: Replace the control board.
- E4: Control board is broken.
- Solution: Replace the control board.
- E5: Short circuit in the control board or the motor is blocked.
- Solution: Check if the motor is blocked. If this does not solve the problem, please contact the supplier.
- E6: Motor broken or motor not connected properly
- Solution: Check if the motor is broken or incorrectly connected, reconnect the wiring if necessary. If this does not solve the problem, please contact the supplier.
- E7: Wires from control board to panel damaged or not connected properly.
- Solution: Check if the wires are connected properly and not damaged, if necessary connect the wires again. If this does not solve the problem, please contact the supplier.
- E8: Appliance is receiving too much electrical power or is overloaded.
- Solution: Check that the load capacity is not exceeded. Reconnect power and restart the treadmill. If this does not correct the problem, contact the supplier.
CONTROL PANEL
- SPORTS MODE Press “START” to start treadmill.
- COUNTDOWN MODE Press “M” to select TIME, DISTANCE or CALORIES mode.
- PRESET PROGRAM (P01-P12) Select program and press “+” or “-” to set time.
Functies
- TIME Displays the training time (0:00 ~ 99:59 minutes). You can also set a training time (5:00 ~ 99:00 minutes). The time is adjusted from the set value to 0, after which the treadmill slowly stops. END” is shown in the display. The treadmill will go into standby mode after 5 seconds.
- STEP Displays steps (0 ~ 9999 steps). The display will toggle from exercise time to number of steps taken. Press “M” to select a single display mode.
- DISTANCE Displays the distance. A distance can also be set. The distance is accumulated from 0 to the set value and then the treadmill stops slowly. END” is displayed. The treadmill will go into standby mode after 5 seconds.
- CALORIES Displays the calories burned. You can also set a goal. The goal is counted down from the set value to 0 and the treadmill stops slowly. END” is displayed. The treadmill will go into standby mode after 5 seconds. The display will change from calories burned to distance. Press “M” to select a single display mode.
- SPEED Displays the speed. The speed can be increased or decreased by pressing “+” or “-“.
NOTE!
- P01 – P12 is displayed under the auto selection setting.
- After the treadmill starts, the display will jump to different views every 5 seconds. Press “M” to select a display mode.
REMOTE CONTROL
-
START/STOP
- Standby or countdown mode: Press “START/STOP” to start the treadmill.
- Program mode: Press “START/STOP” to start the preset program.
- During exercise: Press “START/STOP” to slowly stop the treadmill and put it in standby mode.
- After exercise: Press the button and the treadmill will stop slowly. The data will be retained until the unit is turned off.
-
SPEED
Increase or decrease the speed. -
MODE
- Standby mode: Switch to a different display (TIME – DISTANCE – CALORIES).
- During exercise: Switch between the scrolling display and single display mode.
PROGRAMS
When the treadmill is in standby mode, you can select from 12 preset programs. The programs are shown on page 03.
-
VOLUME
To mute the sound. Press again to restore volume. -
RESET
In standby mode: Resets the data.
Linking the remote control
- Turn off the treadmill.
- Press and hold “SPEED” and “M” on the new remote control for 6 seconds.
- Turn on the treadmill within 5 seconds. The new remote control is paired.
TRAINING GUIDELINES
A successful training program includes a warm-up, the actual training and a cool-down. Perform the complete training program at least twice, but preferably three times a week and keep a rest day between training sessions. After a few months, the intensity of the training can be increased, for example to four or five times a week.
The warm-up
The purpose of a warm-up is to prepare the body for training and to reduce the risk of injury. Warm up your body for two to five minutes before starting a cardio or strength training session. Do exercises that increase the heart rate and warm up the working muscles. Examples of this type of activity are running, jogging, jumping jacks, skipping and running in place.
Stretching
Stretching while the muscles are warm is very important after a good warm-up and cool-down. It reduces the risk of injury. Stretching exercises should be held for 15-30 seconds. Here are some examples of stretching exercises:
- Toe touch (Fig. D-1)
- Inner thight stretch (Fig. D-2)
- Hamstring stretch (Fig. D-3)
- Achilles stretch (Fig. D-4)
- Side stretch (Fig. D-5)
Coolin down
The purpose of the cool-down is to return the body to its (near) normal
resting position at the end of the workout. A good cool-down slowly reduces
your heart rate and promotes recovery.
COMPANY INFORMATION
For an ongoing service request or to purchase parts, please visit;
service@virtufit.nl. Always state the service
number (ITS number) with a question about the current application for a quick
and efficient settlement. A service request must always be submitted via the
service form. So the request not to request service via
info@virtufit.nl.
Do you have a problem with your VirtuFit fitness equipment and would you like
to submit a service request? Then scan the QR code on the right and fill in
our service form.
VIRTUFIT Twekkelerweg 263 7553 LZ Hengelo The Netherlands info@virtufit.nl
ASSEMBLY VIDEO
Documents / Resources
|
virtufit VFWALP100 Walkingpad
100
[pdf] User Manual
VFWALP100, VFWALP100 Walkingpad 100, Walkingpad 100
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>