CubePilot Cube ID Remote ID for Broadcasting Information UAVs Flight User Manual
- June 12, 2024
- CubePilot
Table of Contents
**CubePilot Cube ID Remote ID for Broadcasting Information UAVs Flight User Manual
**
Overview
Cube ID is small size (25mm 13.75mm 3.5mm ) Remote ID which broadcasting information about UAVs in flight through a Bluetooth 5.2 dual-mode unit, supports serial protocol. Use rscan write different codes with one Cube ID only, to adapt to multiple UAVs based on their needs.
Hardware Specification
| Type | Parameter |
|---|---|
| Bluetooth chip | Nordic NRF52840（Bluetooth5.2） |
| Frequency | 2402MHz-2480MHz |
| LDO | MIC5353-3.3 |
| Antenna Name | Wire Antenna |
| Antenna Model | UL1007-26AWG |
| Operation Temperature | -40°C-85°C |
| Dimension | 2513.753.5mm |
| Weight | 10g(with cable and antenna) |
| Protocol | Serial |
Operation instruction
Connect the Cube ID to the TELEM1 Connector of flight control, and view the
transmission data in the mobile phone software Drones.
Installation
Connect the CAN or Serial port on module and flight controller with the sutible cable(weprovide 4 Pin CAN cable,6 Pin and 8 pin Serial cable) . Stick the module to UAV by regular sticker or soft sticker (with slightly vibration isolation). Keep the antenna away from the propeller.
Settings
Remark: Cube ID has not been ready on standard APM firmware . Must create
OpenDroneIDfirmware.Please check following web for build the firmware :
https://ardupilot.org/dev/docs/opendroneid.html#opendroneid
https://www.youtube.com/watch?v=Az8v4Kx4hS0
-
Connect the flight controller to computer via USB cable. Open Mission Planner （latest version）. Install the OpenDroneID firmware firmware by “Load custom firmware”.
-
Go to “Full Parameter List” and find “DID_ENABLE”. Change it to “1” to enableODID.
-
Go to “Full Parameter List” and find “CAN_P1_DRIVER”. Change it to “1” toenable CAN.
（or if you use serial port ,find Serialx_PROTOCAL and change it to mavlink）
-
Go to MissionPlanner homepage select Drone ID to set (1)UAS ID* (2)UADIDType and (3)UA Type
to set (1)UAS ID (2)UAD ID Type and (3)UA Type
Go to Operation to set (1)Operator ID , (2)Oper ID Type , (3)Self
IDDESCand(4)Self ID Type
Testing
Download DroneScanner for IOS， OpenDroneID or DroneScanner for Android to
detect andmonitor nearby UAVs.
Warning
Caution: The user is cautioned that changes or modifications not
expressly approved by theparty responsible for compliance could void the
user’s authority to operate the equipmen.
Second label must be place on the outside of the final device that contains
the following text:
“Contains FCC ID: 2A6CG-HX406252”
The FCC ID can be used only when all FCC compliance requirements are met.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>