SunTouch 500120 ConnectPlus Smart Sensor User Manual
- June 12, 2024
- SunTouch
Table of Contents
SunTouch 500120 ConnectPlus Smart Sensor
SunTouch® ConnectPlus™ Smart Sensor
Description
The ConnectPlus™ Smart Sensor is a temperature and water leakage sensor that pairs to the ConnectPlus thermostat. This device can be used as an optional floor temperature sensor for the radiant floor heating system. Detected water leaks produce audible and visual alarms, and notifications are transmitted to the thermostat.
Where to Use
Temperature Sensor
Place the Smart Sensor directly on a heated section of the floor to use as a
floor control sensor.
Water Leakage Sensor
Place the Smart Sensor directly on the floor where there is a risk of water
leakage (near water lines, washing machines, hot water tanks, …) within range
of the ConnectPlus thermostat.
Specifications
- Power: 2 x AA batteries included
- Battery Life : 1 year
- Range: 75 ft, line-of-sight
- Pairing limit: 6 devices
- Operating Temperature range : 32°F to 104°F (0°C to 40°C)
- Operating Humidity range : 0 to 100% humidity
- Storage temperature range : -4°F to 122°F (-20°C to 50°C)
- IP Waterproof Class : IP67
- Diameter 33⁄8″ (85mm), Height 111⁄16″ (43mm)
WARNING
Please read carefully before proceeding with installation.
Your failure to follow any attached instructions or operating parameters may
lead to the product’s failure.
Keep this Manual for future reference
Setup
Wireless Pairing:
- Put the ConnectPlus into pairing mode: Menu > Settings > Paired Devices > Pair Device
- Press and hold button on the Smart Sensor for 3 seconds Wake: short button press
Status Indicators
Not paired Orange blink
Pairing Orange blink
Paired Green steady
Water Leak Red/Green blink & buzzer
Error Red steady
Low Battery Red blink
Pairing Mode : hold the button down for 3 sec (30 sec timeout)
Silence Buzzer: short button press
Limited 3 Year Warranty
SunTouch warrants this control (the product) to be free from defect in
material and workmanship for a period of (3) years from the date of original
purchase from authorized dealers.
During this period, SunTouch will replace the product or refund the original
cost of the product at SunTouch’s option, without charge, if the product is
proven defective in normal use.
Please return the control to your distributor to begin the warranty process.
This limited warranty does not cover shipping costs. Nor does it cover a
product subjected to misuse or accidental damage. This warranty does not cover
the cost of installation, diagnosis, removal or reinstallation, or any
material costs or loss of use.
This limited warranty is in lieu of all other warranties, obligations, or
liabilities expressed or implied by the company. In no event shall SunTouch be
liable for consequential or incidental damages resulting from installation of
this product. Some states or provinces do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above exclusions or limitations may not apply to
you. This warranty gives you specific legal rights and you may also have other
rights that vary from state to state.
ConnectPlus™ Smart Sensor
The ConnectPlus™ Smart Sensor is a temperature and water leakage sensor that
pairs to the ConnectPlus thermostat. This device can be used as an optional
floor temperature sensor for the radiant floor heating system. Detected water
leaks produce audible and visual alarms, and notifications are transmitted to
the thermostat.
Specifications
| Literature | IOM-ST-CPSS, ES-ST-CPSS |
|---|---|
| Power | 2 x AA Batteries Included |
| Battery Life | 1 Year |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Operating Humidity Range | 0 to 100% humidity |
| Storage Range | -4°F to 122°F (-20°C to 50°C) |
| IP Waterproof Case | IP67 |
| Dimensions | Diameter 33 ⁄8″ (85.38mm), Height 111⁄16″ (42.87mm) |
NOTICE
The ConnectPlus Smart Sensor is only compatible with the SunStat® ConnectPlus model. Does not connect to older model SunStat thermostats.
Status Indicators
Not paired Orange blink
Pairing Green blink
Paired Green steady
Water Leak Red/Green blink & buzzer
Error Red steady
Low Battery Red blink
FCC ID: 2AFJT – CIMDOF18815
IC: 20938 – CIMDOF18815
CAUTION
This Engineering Sheet is not intended to provide full installation instructions and safety information. In order to avoid property damage or injury, please refer to the complete installation manual and product safety information provided with the product.
| Qty | Description | Model# | Order# |
|---|---|---|---|
| ConnectPlus Smart Sensor | 500120 | 81020611 |
SunTouch product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact SunTouch Technical Service. Suntouch reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on SunTouch products previously or subsequently sold. Refer to the owner’s manual for warranty information.
CUSTOMER SERVICES
USA: T: 888-432-8932
• F: 417-831-4067 •
SunTouch.com
Canada: T: 888-208-8927
F: 905-481-2316
Latin America: T: (52) 55-4122-0138
• SunTouch.com
ES-ST-ConnectPlus Smart Sensor 2128 © 2021 Watts
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>