CRYSTORAMA ARA-10267-SB Aragon 7 Light Chandelier Instruction Manual

CRYSTORAMA ARA-10267-SB Aragon 7 Light Chandelier

Product Information

• The CRYS T RAMA model # ARA- 1 0 2 6 7 – S B is a lighting fixture that has been providing illumination for sixty years. It is designed to enhance the ambiance of any space with its stylish and durable construction.
• Assembly of this fixture should be done carefully and in accordance with the provided instructions to ensure proper installation and safe usage.
• Electrical components of the fixture must be installed by a licensed electrician, following the guidelines of the National Electric Code and the relevant local electrical codes. Failure to do so may result in electrical hazards.
• This fixture requires a 7-G9 LED bulb with a maximum wattage of 3.5 watts. For extended usage, it is recommended to use LED bulbs.
• The fixture is dry rated, meaning it can be used in indoor areas that are not exposed to excessive moisture.

Product Usage Instructions

1. Ensure that the power is turned off before starting the assembly or installation process.
2. Follow the provided assembly instructions carefully, ensuring all components are securely attached.
3. If electrical wiring is required, contact a licensed electrician to handle the installation.
4. Select a suitable location for the fixture, considering the desired lighting effect and the availability of power source.
5. Insert the recommended 7-G9 LED bulb into the fixture’s socket, making sure it is properly aligned.
6. Once the assembly and installation are complete, turn on the power to test the functionality of the fixture.
7. If any issues are encountered or if the fixture does not operate as expected, consult the troubleshooting section of the user manual or contact customer support for assistance.

Following these usage instructions will ensure safe and efficient operation of the CRYS T RAMA lighting fixture.

All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes
You will need 7-G9 LED Bulb LED 3.5 Watts Max. USE LED BULBS FOR EXTENDED USE THIS FIXTURE IS DRY RATED

How to install for hanging

Please place the fixture frame on a soft cloth covered table before the installation.
When the fixture is intended to be installed with the shade facing down, please follow the step below:

1. Pull the end caps out of the frame bar by loosening the screws
2. Turn the end cap upside down to making the stud face downward, Insert the end cap back into the ends of the bar and secure with screws.
3. Turn the bar upside down to allow the stud to face upward.

The glass can be installed facing either up or down. Please decide the preferred direction before installing the rod onto the frame

1. Decide the preferred hanging height and choose the correct length of rods needed.
2. Slip the wires through the stems and connect them together. Screw one end of the stem assembly onto the top of the frame and the other end onto the swivel on the canopy.
3. Place the mounting plate over the outlet box and mark four points at the center of the holes on the mounting plate.
4. Drill the holes at the marked points and insert the wall anchors into the hole.Place the mounting plate over outlet box and secure with the anchor screws.
5. Raise the fixture up to the ceiling and do the wire connections. Secure the canopy over the outlet box with the cap nuts.
6. Slide the rubber washer over the socket,and place the crystal shade and check ring over the socket and secure it with the socket ring using the wrench.
7. Install the G9 led bulb into the socket.

DIMENSION

WARNING : This product can expose you to Lead which is known to the state of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov

Part Numbers

• A. Mounting Hardware
  • (1) Mounting Plate
  • (2) Wire Nut
  • (2) Outlet Box Screw
  • (4) Wall anchor and screw
• B. (1) Canopy L56″W4 3/163/4″: XME10267SBCAN56IN
• C. (2) Cap nut
• D. (6) Rod WI/2″*#12″; XME10267SBROD12IN
• E. (2) Rod W1/2″*|6″; XME10267SBROD6IN
• F. (1) Fixture frame
• G. (7) Rubber washer
• H. (7) Crystal Shade W4 S”*H3 H”; XME10261SGLA1. 3IN
• I. (7) Check ring
• J. (7) Socket ring
• K. (7) LED Bulb
• L. (1) Wrench
• M. (1) Wrench

Crystorama.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>