XZENT X-F275 ARGO Series Car Specific Infotainer Instruction Manual

June 12, 2024
XZENT

XZENT X-F275 ARGO Series Car Specific Infotainer

Product Information

The X-F275 is a car-specific infotainer from the ARGO Series by XZENT. It is designed for use in FIAT DUCATO III models of types 250/251, with different model years supported.

Compatibility List

Model Version Model Year
250/251 2006 – 2011
250/251 2011 – 2014
250/251 as of 2014
250/250D/250L as of 2006
250/251 as of 2006

Caution:

  • The installation of the XZENT system should be carried out by an authorized installer. Incorrect installation can cause damage to the vehicle and the XZENT system.
  • Correct functioning can only be guaranteed when using the XZENT original accessories included in the kit or optionally available. Modifying or altering the system or accessories can cause damage.

Note:

  • The vehicle must be factory configured with preinstallation for a radio system. The XZENT system is not compatible with vehicles equipped with an OE radio or an OE navigation system from the factory.
  • Specific adjustments to the battery, charging systems, and power harness layout implemented by the motorhome manufacturer brand are not taken into account in these installation instructions. Contact the relevant motorhome manufacturer for further information.
  • The XZENT system is equipped with an integrated DAB+ receiver. A suitable DAB antenna (not included) must be connected to the system. If the vehicle is equipped with an ex-work OE DAB antenna, a FAKRA to SMB adapter is required for connection.
  • For better radio reception, it is recommended to equip the vehicle with an active antenna system (FM / DAB).
  • If the target vehicle has a resistor-based multifunction steering wheel, no additional accessories are needed to support the steering wheel remote control functions.
  • Software updates to the XZENT system are installed with a USB memory device. Ensure that the USB connection of the XZENT system remains accessible after installation (installation of USB extension cable).
  • If you have questions or problems relating to the XZENT system, please contact the dealer from whom you purchased it.

Kit Includes

No. Item Qty
1 XZENT X-F275 device 1
2 IR remote control 1
3 Two-part metal mounting frame 1
4 Self-tapping Philips screws 4
5 10PIN adaptor cable for 4.2 channel line-out 1
6 6PIN adaptor cable for A/V monitor-in 1
7 12PIN adaptor cable cam power + video-in 1

Product Usage Instructions

To ensure proper installation and functioning of the X-F275 infotainer, follow these usage instructions:

  1. The installation of the XZENT system should be done by an authorized installer who has the specific knowledge and tools required for the installation. Incorrect installation can cause damage to the vehicle and the XZENT system.
  2. Use only the original accessories included in the kit or optionally available from XZENT. Modifying or altering the system or accessories can cause damage.
  3. The target vehicle must be factory configured with preinstallation for a radio system. The XZENT system is not compatible with vehicles equipped with OE radio or OE navigation system from the factory.
  4. Refer to the compatibility list provided to ensure that your vehicle model and year are supported.
  5. If your vehicle is equipped with an ex-work OE DAB antenna, you will need a FAKRA to SMB adapter for connecting the DAB antenna to the XZENT system.
  6. To improve radio reception, it is recommended to equip the vehicle with an active antenna system for FM/DAB.
  7. If your target vehicle has a resistor-based multifunction steering wheel, no additional accessories are needed to support the steering wheel remote control functions.
  8. Software updates to the XZENT system can be installed using a USB memory device. Ensure that the USB connection of the XZENT system remains accessible after installation by using a USB extension cable if necessary.
  9. If you have any questions or problems with the XZENT system, contact the dealer from whom you purchased it.

COMPATIBILITY LIST

Model Model Version Model Year
Fiat Ducato III 250/251 2006 – 2011
Fiat Ducato III 250/251 2011 – 2014
Fiat Ducato III 250/251 as of 2014
Citroën Jumper II 250/250D/250L as of 2006
Peugeot Boxer II 250/251 as of 2006

CAUTION

  • The installation of the XZENT system should be carried out by an authorized installer. S p specific knowledge and tools are required to do the installation. Incorrect installation can cause damage to the vehicle and the XZENT system.
  • Correct functioning can only be guaranteed when you use the XZENT original accessories included in the kit or optionally available. The XZENT system and the original accessories must under no circumstance be modified or altered in any way. Inappropriate actions can cause damage to the vehicle and the XZENT system.

NOTE

  • The target vehicle must factory configured with preinstallation for a radio system. The XZENT system is not compatible with vehicles that are equipped with an OE radio or OE navigation system from the factory.
  • This device installation manual applies to vehicle platforms appearing in the above compatibility list, and in a condition as offered by the respective vehicle manufacturer. Deviating equipment and specific adjustments to battery-, charging systems and power harness layout implemented by the given motorhome manufacturer brand are not taken into account in these installation instructions. Please contact the relevant motorhome manufacturer.
  • The XZENT system is equipped with an integrated DAB+ receiver. To make use of this you will need a suitable DAB antenna (not included in kit) that must be connected to the XZENT system. If vehicle is equipped with ex-work OE DAB antenna, a FAKRA> SMB adapter is required for connection.
  • In order to obtain better radio reception, it is recommended to equip the vehicle with an active antenna system (FM / DAB).
  • If the target vehicle is equipped with a resistor based multifunction steering wheel, no additional accessories are needed to support the steering wheel remote control functions.
  • Software updates to the XZENT system are installed with a USB memory device. Therefore when fitting the system make sure that the USB connection of the XZENT system will still be accessible later (installation of USB extension cable).
  • If you have questions or problems relating to the XZENT system, please contact the dealer from whom you purchased it.

THE KIT INCLUDES

 | No.| Item| Qty|
---|---|---|---|---
1| XZENT X-F275 device| 1|
2| IR remote control| 1|
3| Two-part metal mounting frame| 1|
4| Self-tapping Philips screws| 4|
5| 10PIN adaptor cable for 4.2 channel line-out| 1|
6| 6PIN adaptor cable for A/V monitor-in| 1|
7| 12PIN adaptor cable cam power + video-in| 1|
8| 4PIN adaptor cable A/V monitor-out| 1|
9| Microphone with 3m cable extension and 3.5 mm jack| 1|
10| Parking brake connection cable| 1|
11| Main wire harness ISO/DIN| 1|
12| SWC interface adaptor| 1|
13| FM antenna adaptor ISO/DIN| 1|
14| GPS-antenna with 90° angled connector and 3 m cable extension| 1|
15| Doublesided 3M self-adhesive pad for GPS antenna| 1|
16| Main device manual for X-F275| 1|
 | 17| USB extension cable with 80 cm length (gray / black)| 2|

TOOLS REQUIRED

  • Torx screwdriver T25
  • File
  • Phillips screwdriver
  • Release tool made of plastic
  • Fabric tape
  • Hand saw or equivalent tool

INSTALLATION

REMOVAL WORK AND PREPARATION

  1. Remove both storage compartments in accordance with the manufacturer‘ s information.

  2. Cut off the left and right plastic holders for the storage compartments as fl ush as possible.

  3. Use a suitable saw to do this, and then a fi le to remove any protrusions still present.
    INSTALLATION

  4. Remove the two original Torx screws at the top (T25).

  5. Insert the two-part mounting frame (No. 3) at an angle from above into the radio slot.

  6. Screw down the mounting frame at the top and bottom with the four Phillips screws (No. 4) supplied with the XZENT system kit.

  7. Fit the GPS antenna (No. 14) at a suitable place, and make sure that the GPS reception is not adversely affected due to shadowing by metallic vehicle parts (thermal glazing etc.). Next run the connecting cable to the radio slot.

  8. If you wish to use it, now fit the external Bluetooth microphone (No. 9) supplied, and run the connecting cable to the radio slot. Depending on preference and your choice of an external or device-internal microphone, the microphone source for the Bluetooth mode must be correspondingly changed in the device menu.

  9. Run the USB extension cable (No. 17) from the radio slot to the position you want.
    OPTIONAL

  10. If your Car is equipped with a resistor based multifunction steering wheel you have to connect the enclosed SWC-adapter (No. 12) with the Main connection cable (No. 11) and the 20-pin connector on the vehicle side.

  11. Connect the main cable (No. 11) of the XZENT system (No. 1) to the ISO plug connectors of the vehicle. When using a reversing camera system, the reversing signal from the vehicle must be connected to the reverse connection of the XZENT system for automatic switching. Relay the handbrake signal from the handbrake and connect it to „Parking“ to enable videos playback function with stationary vehicle.
    ATTENTION
    Playback of videos while driving is not permitted by law. For this reason the video playback function is blocked while the vehicle is moving / driving.

  12. Connect all the cables to the XZENT system (No. 1): those previously run in the radio slot, and the original antenna cable. If necessary, use the ISO DIN antenna adapter (No.13) included in the kit. Next slide the XZENT system carefully into the radio slot until it is heard to engage.

NOTE

  • Make sure that all connectors at the rear of the unit have sufficient room and are not bent.
  • For vehicles with an original FIAT active antenna, it is necessary to ensure a power supply for the antenna. Pay particular attention that the plug connectors of the P.ANT lead of the main connection cable (No. 11) are connected together.
  • Connectors without a retaining mechanism must also be secured with insulating tape

COMMISSIONING
Make sure that the vehicle is outside, and that the GPS reception is not adversely affected by any shadowing (trees, high buildings etc.). Insert the separately purchased navigation software SD card supplied into the SD card slot of the XZENT system, and start it in order to establish a sat fix. Make sure that the vehicle is not moved until the sat fix is established. Now press the NAV button to start the navigation mode, and choose map view. Once your present location can be seen in the map view the sat fix will be automatically established. This can take 3 to 5 minutes. You can now use the XZENT system. Finally carry out a general functional test, and make the basic settings. Also ensure that no fault warnings appear on the vehicle side.

Electrical characteristics
Power supply: +12 V DC against vehicle ground
External protection against internal short-circuit: 15 A Mini-ANL fuse

Operating currents

  • ACC off idle status: <5.0 mA
  • Audio / video playback (VOL 20): ~ 1.40 A
  • GPS mode with active route guidance (VOL 20): ~ 1.55 A
  • GPS mode with active route guidance (VOL 40): ~ 3.80 A

@ 13.8 V operating voltage with front and rear 4 ohm loudspeaker connected to device

Connection Diagram

XZENT-X-F275-ARGO-Series-Car-Specific-Infotainer-fig-1
\(10\) XZENT-X-F275-ARGO-Series-Car-
Specific-Infotainer-fig-1 \(11\) XZENT-X-F275-ARGO-Series-Car-Specific-Infotainer-fig-1
\(12\)

XZENT by ACR AG

Stand Januar 2021· Rev. A

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals