XZENT X-427 2-DIN Infotainer or Naviceiver with DAB Plus or USB and Bluetooth User Manual

User Manual

X-427
Navitainer X-427

ABOUT THIS MANUAL
This manual contains important information and warnings about the operation of this XZENT unit.
Please store it in a place where you have access later on.

SAFTY INFORMATION

General

1. The descriptions and other content shown in this manual may deviate from the real device.
2. Pictures shown in this manual and some HMI screenshots may deviate from the real unit.
3. Specifications and technical design of this device model are necessarily subject to change without notice.

• Read the instructions entirely. Heed all warnings. Follow the instructions.
• Retain this manual. Whoever will use the unit should have access to this manual.
• This unit is designed to be functional in vehicles with 12 V DC battery and negative ground.
• Do not operate the unit in any other way than described in this manual. Failure to follow the instructions as provided may void your warranty.
• Do not disassemble or alter the unit in any way because this will void your warranty. Do not attempt to repair or to service the unit yourself, but contact an authorized XZENT dealer instead.
• Use only original accessories which are designed and manufactured for the unit, otherwise you will risk damage. Install the unit according to the mounting instructions by using the supplied mounting accessories. Acceleration forces during accidents can be huge. Incorrectly mounted devices pose a serious risk for the driver and passengers during an accident.
• Protect the unit from water and other liquids that could enter the housing. A short circuit or even a fire could result.
• Before you replace a defective fuse try to find the cause for the short circuit. Pay attention to the cables of the power supply! If the short circuit does not result from a failure of the power supply or wiring, you can replace the defective fuse with a new one (of identical value). If the short circuit persists, contact an authorized XZENT dealer.
• When connecting to any other device, read the user‘s guide for compatibility and notes on electrical connections. Do not try to connect incompatible products.
• Be careful not to drain the car battery while using the unit when the car engine is turned off. Because the unit consumes a considerable amount of energy and the battery will be charged only while the engine is running, it might happen that the battery will discharge to a point where it is not possible to start the engine anymore.
• According to the law in different European countries, driving with monitors showing movies in the viewing range of the driver is not allowed, because the driver might get distracted from traffic. Please respect the traffic regulations of your country or you may face legal penalties in case of accidents or even lose your insurance coverage. Pay attention to the playback volume inside your vehicle since you are required to notice exterior warning sounds like police sirens etc..
• Don‘t expose the unit to hard impacts. A mechanical or electrical malfunction of the unit could be the result.
• Should any problems or questions occur during the installation, please consult your XZENT dealer/importer.

DEVICE SUPPORT, SOFTWARE UPDATES AND MAINTENANCE

Software updates and improvements are provided via USB updates which can be downloaded from our website www.xzent.com Also customer care, FAQs and other helpful information can be found there.
ATTENTION: this device has specific USB ports with special functions (USB-1/top port at device backside) and (USB-2/bottom port at device backside). The extension cables are distinguishable thru text-label to ensure proper identification.
Software updates provided via XZENT MUST be installed on “USB-1” (USE FOR SW UPDATE). If the installation has been done by 3rd party without proper marking/identification of the extension wire – do try the other port in case of update-failure.

FRONT PANEL

Operation buttons:

1. VOL/POWER:| Press and hold for standby mode (Screen OFF, Audio OFF).
If powered on, press to mute.
If powered off, press to power on.
Rotate clockwise to increase audio volume.
Rotate anti-clockwise to decrease volume.
---|---
2. HOME:| Press to return to home screen.
Press in home screen to go to last source (if available).
Press and hold to open EQ.
3. FAV:| Press to execute assigned FAV short press function from device settings (see chapter device settings).
Press and hold to execute assigned FAV long press function from device settings (see chapter device settings).
4. CAM:| Press to show default camera, press again to close the camera view.
5. NAV:| Press to open navigation mode.
A.  RESET:| Press to perform a power reset.
B. MAP:| MicroSD slot for navigations software (optional, not included in this set).
C.  MIC:| internal microphone for handsfree functions.
D.  IR:| IR lense for remote control.

MAIN MENU

MAIN MENU operation buttons and display

To browse the different source icons, swipe left or right. Alternatively you can press the arrow keys to browse the different pages.
To return to this screen you can press the HOME front sensor key or the return arrow button in top left corner of every source.

STEERING WHEEL CONTROL (OE MODE, IR-STALK-INTERFACE)

The XZENT device is pre-configured to work with an IR-Stalk-Interface which is NOT included in the set. To use the IR-Stalk interface a XZENT compatible IR- Stalk-Adapter of your Vehicle type needs to be purchased and installed. Alternately an existing steering wheel control can be connected to the Key1/ Key2 inputs. For the Fiat Ducato X290 this set includes a red miniISO- Connector which can be plug and play connected to Key1/Key2 inputs. On default the Fiat Ducato X290 steering wheel control functions
are assigned but you can re-assign or change this in the Analogue-Key-Mode (see next chapter). Non standard is the CAM function which is set to the left bottom SWC key – this is XZENT specific. Other vehicles than Fiat Ducato X290 with resistive steering wheel control buttons can also be connected to Key1/Key2 inputs – but need reassign or change the default values before first use of the SWC.

Possible button functions and general buttons

1| Mute| short press to mute the XZENT audio output. Press again to undo the mute function.
---|---|---
2| Vol-| short press to reduce the volume of the current active audio channel (media vol, Nav.
voice, etc.).
3| Vol+| short press to increase the volume of the current active audio channel (media vol,
Nav. voice, etc.).
4|   Skip back| short press to while media source DAB, USB, FM, etc. is active to do the same
touchscreen button operation.
5| Skip next| short press to while media source DAB, USB, FM, etc. is active to do the same
touchscreen button operation.
6|  Pickup| short press to accept incoming call.
7| Hang Up| short press to end ongoing call.
8| SRC| short press to change source.
9| FAV| short press to execute assigned FAV function from device settings (see chapter
device settings).
10| CAM| short press to open camera source. Press again to close.
11|  Change| short press to remove current steering wheel button assignments and reassign them
(see next Chapter).
12| Default| short press to load Fiat Ducato X290 default values.

SWC (re)Assignment
In case your XZENT device is connected via Key1/Key2 Inputs to your resistive steering wheel control buttons you can directly use the Fiat Ducato X290 default functions or reassign them. For other vehicles than Fiat Ducato X290 you need to initially assign them before first use of the analogue/resistive steering wheel control buttons.

1. To change or re-assign the functions press the „Change“-Button (11).
2. The system now highlights the next non-assigned function to be assigned. However you can press a different function on the touch screen to learn the functions in your preferred sequence.
3. To assign the marked functions to a steering wheel control button – press the button on the steering wheel control while the functions is highlighted. On success the function is displayed in white and the system will mark the next free un-assigned function for you automatically. Repeat this step until you have assigned all needed functions to your remaining steering wheel control buttons.
4. To safe the changes leave the screen by tapping to the upper left back button.

Note:
CAN based steering wheel controls require a compatible XZENT IR-Stalk adapter for your vehicle type which is sold separately. The XZENT IR-Stalk interface needs to be connected to correctly including the IR-Input of your XZENT device.
Analogue/resistive steering wheel controls can be connected via Key1/Key2 inputs. For Fiat Ducato X290 a plug and play red miniISO connector is included and can be directly connected if the Fiat Ducato X290 is equipped with a steering wheel control. Other vehicle types with analogue/resistive steering wheel control needs to be correctly connected to Key1/Key2 inputs and do an initial assignment first.

DEVICE SETTINGS

Operation Buttons:

1. Return
   Press to return to the home screen.

2. List area
   The shown list area is depending on the currently selected category.
   To see other settings you can scroll/swipe the list up and down or select different category from the lower area.

3. General
   Contains general settings like language, date & time, FAV key assignment.
   3(a) Language: Press arrow keys to select language.
   3(b) DAB+ Time sync mode: Press switch to ON/OFF setting.
   3(c) FAV short press: Press arrow keys to assign a different function.
   3(d) FAV long press: Press arrow keys to assign a different function.
   3(e) Beep: Press switch to ON/OFF setting (Enable/Disable key press beeps).
   3(f)  Microphone: Press arrow key to change selected microphone.
   3(g) Background: Press to select a different background.
   3(h) Sensor Button illumination, press to change.
   3(i) Time zone: Press arrow keys to set a time zone (only possible if the sync modus is set to OFF).
   3(j) 12/24: Press arrow keys to change 12/24h format.

4. Audio

Contains setting for audio and sound adjustments.
4(a) Balance: Press arrow keys to shift the center to left or right position.
4(b) Fader: Press arrow keys to shift the center to front or rear position.

4(c) Equalizer:
Press to open EQ. You can select different EQ-Presets or manually change the frequency bands to your liking.
Balance and Fader can also be optically adjusted or LPF, Subwoofer level and Loudness can be adjusted.

4(d) Navi Mixer: Press switch to activate or deactivate mixing of navigation voice and background audio.

4(e) Startup volume: Press more key. Here you can change individually all available sources in regard of startup volume.

You can choose to apply the last used volume, or set a fix volume on startup.

5. TFT

Here you can adjust settings in regard of the screen for example brightness mode or brightness values.

5(a) TFT brightness day: Press arrow keys to set value for day mode.

5(b) TFT brightness night: Press arrow keys to set value for night mode.

5(c) Dim mode: Press arrow keys to set value.

Auto: the brightness is adjusted automatically with switching on the front headlights of the vehicle (Night).

 Day: the brightness is permanently at day value.

 Night: the brightness is permanently at night value.

5(d) Touchscreen Auto Standby: On set idle time, the screen will be powered off when not operated (audio will continue in background).

6. Camera

Enables you to adjust settings on the connected rear view camera.

6(a) Rear View Camera: Press arrow keys to adjust value.

6(b) Reverse Mute: Press to change value (Volume 50%, Mute 0% or 100% no muting)

6(d) Reverse delay: Press arrow keys to change the delay time until the cam view auto closes after leaving reverse gear.
6(e) Camera picture: Press arrow keys to adjust value (normal or horizontal mirrowed).

7. Miscellaneous
   Here you can find information on the software device version, load factory defaults or adjust the steering wheel controls (only if the vehicle is connected to via Key1/Key2 [mini ISO] but not via an IR stalk Interface).

7(a) Factory default: Press more key and confirm to perform a factory reset.

7(b) Software installation: Press to start update (USB-1).

7(c) Software version: Press more key to show the device system software version.

7(d) SWC assignment: Press to open the SWC assignment screen for Analogue-Key mode (not for IR-Stalk Interface mode).

DAB RADIO SOURCE

You can enter the DAB source among other ways via the front panel DAB sensor key or via the Home Screen Source Icon. You can also directly switch from the FM source to DAB source via the DAB key in lower right corner of the FM source.
With the DAB source you can enjoy the enriched digital radio services which are possible via the new DAB+ standard. In the lower section you can change the category which will update the main area of the source accordingly.

Operation buttons

1. Return
   Press to return to the home screen.

2. Settings
   2(a) DAB-DAB Service Following: Press to switch function ON/OFF.
   2(b) Antenna supply: Press switch to activate/deactivate 12V power supply for your DAB antenna.
   2(c) DAB Firmware: Shows current DAB firmware version.

3. Info
   This view allows you to see current played station logos, slideshow pictures and text which is aired from the station.
   Press the arrow keys to change the station of current selected ensemble.
   Press and hold the arrow keys to change to next possible ensemble–the first station of new ensemble will be auto played.

4. List
   The list view allows you to see all received ensembles and will be periodically refreshed.
   You can select an ensemble by tapping on it and it will show the containing stations which you also can directly tap to play.

5. Preset
   This view show the preset buttons that work like a quick select or favorite button.
   To save the current station to a preset button, press and hold it until the button is updated with the station information.

6. FM
   Press the button to change directly to FM radio source.

Notes:
Please note that some features depend on the aired station or the reception.

FM RADIO SOURCE

You can enter the FM source among other ways via the front panel via the Home Screen Source Icon. You can also directly switch from the DAB source to FM source via the FM key in lower right corner of the DAB source. In the lower section you can change the category which will also update the main area of the source accordingly.

Operation buttons

1. Return
   Press to return to the home screen.

2. Settings
   With the settings menu, you can initiate an auto search & store for the presets, change AF behaviour or the reception mode.
   2(a) Auto Save: Press the key arrows to initiate auto search & store for the presets.
   2(b) Mode: Press the key arrows to change DX/LOC mode.
   2(c) AF: Press switch to ON/OFF AF-function (Alternative Frequencies).

3. Scale
   This view will display a frequency scale band with a marker of the current tuned frequency.
   Between the up and down seek buttons (arrow keys) the frequency is additionally displayed.
   Press the arrow keys to initiate up/down seek to the next receivable station.

4. Info
   This view will show you the station name and the received radio text.
   Between the up and down seek buttons (arrow keys) the frequency is additionally displayed.
   Press the arrow keys to initiate up/down seek to the next receivable station.

5. Preset
   This view show the preset buttons that work like a quick select or favorite button.
   To save the current station to a preset button, press and hold it until the button is updated with the station information.

6. TA
   Press button to ON/OFF TA (Traffic Announcement).

7. DAB
   Press button to directly switch to DAB radio source.

Note:
This unit features an RDS tuner. RDS is a system which transmits data on top of the FM radio signal. Availability and content of the RDS data depend on the respective broadcast station and its signal strength. RDS does, for example, transmit alternative  requencies, which allow for frequency changes without user interaction. You need to have the AF function activated in order to use the RDS functionality and features.

USB/IPOD/BT MUSIC (A/V) SOURCE

The sources USB and iPod can be accessed among other ways thru their home screen icon and BT music with a connected phone via the Bluetooth source to play audio (BT, USB, iPod) or video (USB only). Playing files is similar for all sources and can be controlled via the media player UI. To play videos in USB mode you need change the standard filter in list view (4) to the video fi le type (B).

In this main view the media player controls are displayed. As usual you can use the pause/resume/play or skip buttons to play the next track. You can also activate the special functions like repeat and shuffle.
Operation buttons:

1. Return: Press to return to the home screen.
2. EQ: Press to open equalizer settings (see chapter device settings).
3. Search: Press to open search (not available in Bluetooth music).
4. List: Press to open the list view (not available in Bluetooth music).

At the list view mode (not available in Bluetooth music) you can browse your media files similar like a folder-file list. To open folders just simply tap on them to show their content which you also can directly tap to start playback. It will be shown with a play icon and also at the bottom line. To go back one level use the back (A) button or you can change to the video media type (only USB mode) by pressing (B) the filter icon.
Additional notes on Video playback:
The video playback is only possible if the handbrake is engaged.
The playback will be in full screen mode – to leave the full screen mode press simply the touch screen area of your device.

BLUETOOTH PAIR, CONNECT, CALL, MUSIC

On initial use the category (2) is active and you can pair your compatible phone via scan/search. Please ensure your phone is visible until it appears in the search result list. To pair tap the line with your phone from the list and confirm the pass key. Please also ensure that permission such as to contacts are granted/accepted. Active or auto connected phones are shown in status area (A) with an active Bluetooth icon, battery and signal strength icon (if supported).
In the lower section you can choose a different category which will update the main view area.

Operation buttons

1. Return
   Press to return to the home screen.

2. Devices
   Here you can manage your paired phones (manual connect/disconnect, delete) or add new phones via search.
   Tap the connect/disconnect button to disconnect manually and connect a different other phone.
   Tap the waste bin icon button to delete a paired phone
   Note: it is only possible to connect a single phone at the same time.

3. Keypad
   Press to open the dial keypad with the active phone.

4. Contacts
   Press to open the contact list of the active phone.
   You can manually re-sync in case if not all contacts are shown or new contacts have been added to the phone.
   You can slide the list or use the search function to look up a contact.
   A contact can be operated like a folder and be tapped to open its containing numbers.
   Tap on the line number to initiate a call attempt.
   Use the orange back button on top left position of the list view to browse one level up.

5. Call log
   Here you have a separate list view for outgoing, received/incoming or missed calls.
   You can tap a line to initiate a call attempt.

6. Music
   Press to initiate the Bluetooth music playback via A2DP.
   Note: Some smartphones need to start the music app on the smartphone first.
   The usage of Bluetooth music player is described in chapter „USB/IPod/BT Music (A/V) Source“

7. Settings Press to open the Bluetooth settings for extended options like auto connect, auto answer contact list settings and microphone adjustments.
   6(a) Auto Connect: Press switch to ON/OFF Auto Connect.
   6(b) Auto Answer: Press switch to ON/OFF Auto Answer.
   6(c) Microphone Gain: Press arrow keys to change values.
   6(d) Contact Order: Press arrow keys to change value.

On incoming/outgoing or active call, the device will automatically switch to a full screen mode and shows you the contact name or number (if available) or unknown in case of a suppressed caller ID. Depending on the call status (initiate, ringing, dialing, active) you can hang-up, reject, accept/pick-up a call (1), on active call you can switch to private mode (2) or to car loudspeakers, mute the XZENT microphone (3) or open the keypad for call options (4). (5) Press to return to navigation mode.

NAVIGATION SOURCE

The Navigation source can be entered among other ways via the home screen icon or the sensor NAV front key.
Please insert the microSD card to the NAV slot on found on upper left side of the device (see Front View Chapter).
For the Navigation source UI operation a quick start guide is provided, you can also download a navigation manual (PDF) from our web site.
Navigation Software and map updates:
The navigation software and maps on your microSD card is maintained and updated via www.naviextras.com
You can find additional information, help and instructions how to install the toolbox and performing the desired action.

ANDROID LINK

With Android Link you can connect your compatible Android Phone to the XZENT device and enjoy compatible smartphone apps in your car. Make sure that you enabled the Android Link function in the system settings of your XZENT device.
Warning!
Please keep in mind that in certain countries it is illegal to operate a smartphone while driving.
XZENT is not liable for any problems or incorrect use of app-based content. Using connected content should respect your phones data plan to avoid additional costs.

1. To use this functionality you need first download the Auto Link Host App from your App-Store.
2. Launch the Auto Link Host App on your phone
3. Unlock your Phone and connect it via USB-1 (usually this port is connected to the vehicles OE-USB port at your vehicle) to your XZENT.
4. Press the Android Link home screen icon on your XZENT
5. On initial connection allow/accept requested access and accept and Bluetooth pairing request.

A/V-IN SOURCE

The A/V-IN can be entered among other ways via the home screen icon. Here you have the possibility to listen to audio from an external device connected via audio line in with your XZENT via vehicle loudspeaker.
Operation Buttons

1. Return
   Press to return to the home screen.

TERMS OF WARRANTY

What products are covered by XZENT's limited Warranty?

What is the validity period of XZENT's Warranty?

Under this Warranty, CENT warrants, for a period of 2 years, that the product is free from defects in material and/or workmanship at the time of the original purchase. This 2-year period commences on the date of the original purchase as per the original invoice or until receipt. If you have purchased the product as a consumer, and the defect is identified within the first six months after the original purchase (see above), we will assume that the defect already existed at the time of purchase

Who can claim under the Warranty?

CENT grants the limited Warranty to natural persons only, who purchased the relevant product primarily for personal use..

What is covered by the Warranty?

Is XZENT liable for other defects or damage?

CENT will repair or replace products, only if they are covered by the terms of this Warranty. CENT is not liable for any material or intangible loss or damage such as the price paid for the product, loss of profits, revenue, data, or relating to the enjoyment of the product or components associated with it, arising directly or indirectly under this Warranty or otherwise in relation to products or services. This likewise applies to loss or damage relating to the impairment or operational failure of the product, or devices associated with it, caused by defects or the non-availability of the product during the time it is with CENT or CENT's service partner, as well as to periods of downtime and business interruptions. In addition, CENT does not accept any liability for shipment-related risks - such as the loss or destruction of the product - in connection with the fulfilment of the Warranty. This disclaimer applies to losses of damage irrespective of the legal basis, especially on the grounds of negligence, other wrongful conduct (torts), breach of contract, express or implied guarantees, and strict liability (even if CENT or its service partner has been advised of the possibility of such damage occurring). If these disclaimers are prohibited or limited under the applicable law, CENT will limit its Warranty and liability to the extent permissible under the applicable regulations. For example, some national laws prohibit the exclusion or limiting of damages payable in connection with negligence, gross negligence, willful wrongdoing, deceitful conduct, and other such acts. For the duration of this Warranty, all liability that cannot be excluded completely will be limited to the extent permissible under the applicable law. Liability under this Warranty is limited to the price paid for the product. If the applicable law only permits higher limits on any liability, this higher limitation will apply.

How do I exercise my Warranty rights?

If you want to exercise your entitlements under this Warranty, please contact the authorized dealer where the product was purchased, and present it with the original copy of the till receipt or invoice. Do not return any products to CENT directly, otherwise our Warranty obligations cannot be fulfilled. You will find the name of the relevant dealer or reseller on your proof of purchase Defective devices sent by the authorized dealer to the service center, must also be accompanied by any accessories with a logical connection to the observed fault. This means, for example, the navigation package on an SD or microSD card supplied or purchased with the device, if problems or functional errors were observed in connection with the navigation function.

How will XZENT fulfil its Warranty?

CENT or its service partner will choose to either repair or replace the product or its defective parts covered by the Warranty, and assume the costs of material and labor in doing so. Repairs under the Warranty must be carried out by CENT or its authorized service partner. Products that are repaired or replaced may contain new and/or refurbished components and devices. Components that are swapped out will become the property of CENT.

Will I incur any costs in connection with the Warranty service?

CENT assumes the costs of material and labor in connection with its Warranty service. The Warranty holder is responsible for the costs of shipment and bears the risks connected with the shipment (see above). If the product is found to be operating faultlessly, or there is no warranty entitlement because the warrant period has expired or for any other reason, CENT or its authorized service partner will be entitled to charge a flat-rate investigation fee of E30.00.

Do this Warranty affect my statutory or contractual rights?

This Warranty is made voluntarily by CENT, and it will, in any case, extend your statutory rights. As a consumer, you remain fully entitled to your statutory rights, such as the statutory guarantee. This Warranty also has no effect whatsoever on your contractual rights against the reseller. You may continue to exercise these rights in full.

ADDITIONAL INFORMATION

Hereby, ACR Brändli + Vögeli AG declares that the type of radio equipment X-427 complies with the 2014/53/EU Directive. The full text of the EU Declaration of Conformity is available at the following Internet address: www.xzent.com (see link „Product Conformity Documents“ in the footer of the page).

TECNICAL SPECIFICATION

Electrical characteristics
Power supply: +12 V DC against vehicle ground
External protection against internal short-circuit: 15 A Mini-ANL fuse
**Operating currents***
ACC off idle status: <5.0 mA
Audio / video playback (VOL 20): ~ 1.40 A
GPS mode with active route guidance (VOL 20): ~ 1.55 A
GPS mode with active route guidance (VOL 40): ~ 3.80 A

• @ 13.8 V operating voltage with front and rear 4 ohm loudspeaker connected to device
  Bluetooth
  Transmit frequency band: 2.4 GHz
  Transmit power: max. 100 mW
  Radio Frequency Exposure Information
  This device complies with EU requirements (2014/53/EU Article 3.1a) to limit exposure of the general public to electromagnetic fields for health protection.
  Do not use the device in locations where wireless devices are not allowed.
  XZENT cannot guarantee that accidents or damage will not occur due to improper use of the device. Use this product with care and at your own risk.
  Recycling Notes
  This product bears the symbol for selective sorting of Waste Electrical and Electronic Equipment (WEEE). This means that this product must be treated in accordance with European Directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to hand over his product to a competent recycling organization or to the retailer when a new electrical or electronic device is purchased.

XZENT by ACR AG
Bohrturmweg 1
Bad Zurzach
Switzerland
www.xzent.com
EU Legal Representative:
ACR S & V GmbH
IndustriestraBe 35
D-79787 Lauchringen
Germany

References

• Naviextras.com - Map updates for your navigation device and more...
• XZENT – Mobile Solutions für Ihr Fahrzeug

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>