Hotpoint H2F HL626 UK Dishwasher User Guide

June 12, 2024
Hotpoint

Hotpoint H2F HL626 UK Dishwasher User Guide

Hotpoint H2F HL626 UK Dishwasher.jpg

THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please register your appliance on: www.hotpoint.eu/register

You can download the Safety Instructions and the User Manual, by visiting our website docs.hotpoint.eu and following the Instructions on the back of this booklet.

Before using the appliance carefully read Safety Instructions guide.

PRODUCT DESCRIPTION

APPLIANCE

FIG 1 APPLIANCE.JPG

CONTROL PANEL

FIG 2 CONTROL PANEL.JPG

  1. On-Off/Reset button with indicator light
  2. Program selection button with indicator light
  3. Half Load button with indicator light
  4. Rinse Aid refill indicator light
  5. Salt refill indicator light
  6. Program indicator lights
  7. Delay indicator light
  8. Delay button with indicator light
  9. Tablet (Tab) button with indicator light
  10. Start/Pause button with indicator light / Drain out

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components.

  • It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
  • It is important to set the water hardness.

FIG 3 FILLING THE SALT RESERVOIR.JPG

Make sure the cap is screwed on tightly, so that no detergent can get into the container during the wash program (this could damage the water softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the water hardness setting is based on the actual water hardness in your house. This information can be obtained from your local water supplier. The factory sets the default value for the water hardness.

  • Switch on the appliance by pressing the ON/OFF button.
  • Switch off the appliance by pressing the ON/OFF button.
  • Hold down button START/Pause for 5 seconds, until you hear a beep.
  • Switch on the appliance by pressing the ON/OFF button.
  • The program indicator light of the current set level flashes.
  • Press button P to select the desired hardness level (see WATER HARDNESS TABLE).

FIG 4 SETTING THE WATER HARDNESS.JPG

• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!

As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator light switches off.

If the salt container is not filled, the water softener and the heating element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.

FILLING THE RINSE AID DISPENSER

FIG 5 FILLING THE RINSE AID DISPENSER.JPG

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.

  • Switch the dishwasher on using the ON/OFF button.
  • Switch it off using the ON/OFF button.
  • Press button START/Pause three times – a beep will be heard.
  • Switch it on using the ON/OFF button.
  • The program indicator light of the current set level flashes.
  • Press button P to select the level of rinse aid quantity to be supplied.
  • Switch it off using the ON/OFF button

Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specific to the model, please follow instruction above to check this for your machine.

  • If you see bluish streaks on the dishes, set a low number (2-3).
  • If there are drops of water or limescale marks on the dishes, set a mid-range number (4-5).

FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C.
Introduce the detergent into the dry dispenser D only. Place the amount of detergent for pre-washing directly inside the tub.

  1. When measuring out the detergent refer to the mentioned earlier information to add the proper quantity.
    Inside the dispenser D there are indications to help the detergent dosing.

  2.  Remove detergent residues from the edges of the dispenser and close the cover until it clicks.

  3. Close the lid of the detergent dispenser by pulling it up until the closing device is secured in place.

The detergent dispenser automatically opens up at the right time according to the program.
If all-in-one detergents are used, we recommend using the TABLET button, because it adjusts the program so that the best washing and drying results are always achieved.
Usage of detergent not designed for dishwashers may cause malfunction or damage to the appliance.

PROGRAMS TABLE

FIG 7 PROGRAMS TABLE.JPG

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.
1 ECO
Eco programme is suitable to clean normally soiled tableware, that for this use, it is the most efficient programme in terms of its combined energy and water consumption, and that it is used to assess compliance with the EU Ecodesign legislation.

2 INTENSIVE
Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).

3 MIXED
Mixed soil. For normally soiled dishes with dried food residues.

4 RAPID 28’
Program to be used for half load of lightly-soiled dishes with no dried food residues. Does not include drying phase.

5 SOAK
Use to refresh crockery planned to be washed later. No detergent to be used with this program.

Notes:
Please note that cycle Rapid 28’ is dedicated for lightly soiled dishes.

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.

FIG 8 OPTIONS AND FUNCTIONS.JPG

LOADING THE RACKS

FIG 9 LOADING THE RACKS.JPG

FIG 10 LOADING THE RACKS.JPG

DAILY USE

  1. CHECK WATER CONNECTION
    Check that the dishwasher is connected to the water supply and that the tap is open.

  2. SWITCH ON THE DISHWASHER
    Press the ON/OFF button.

  3. LOAD THE RACKS (see LOADING THE RACKS)

  4. FILLING THE DETERGENT DISPENSER

  5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
    Select the most appropriate program in accordance with the type of crockery and its soiling level (see PROGRAMS DESCRIPTION) by pressing the P button.
    Select the desired options (see OPTIONS AND FUNCTIONS).

  6. START
    Start the wash cycle by pressing the START/PAUSE button. When the program starts you hear a beep.

  7. END OF WASH CYCLE
    The end of the wash cycle is indicated by beeps and by the flashing of the wash cycle indicator on the panel. Switch off the appliance by pressing the ON/OFF button and open the door. Wait for a few minutes before removing the crockery – to avoid burns. Unload the racks, beginning with the lower one.

The machine will switch off automatically during certain extended periods of inactivity, in order to minimise electricity consumption.
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the amount of detergent used accordingly.

MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided that it has only just begun: press and hold the ON/OFF button, the machine will switch off. Switch the machine back on using the ON/OFF button and select the new wash cycle and any desired options; start the cycle by pressing the START/PAUSE button.

ADDING EXTRA CROCKERY
Without switching off the machine, open the door (be ware of HOT steam!) and place the crockery inside the dishwasher. Close the door and press the START/PAUSE button the cycle will begin from the point at which it was interrupted.

ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power cut, the cycle stops. Once the door has been closed or the electricity supply is restored, to start again the cycle from where it was interrupted, press the START/PAUSE button.

ADVICE AND TIPS

TIPS
Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand under running water.

Arrange the crockery so that it is held in place firmly and does not tip over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing the water to reach every surface and flow freely.
Warning: lids, handles, trays and frying pans do not prevent the sprayer arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket because in this sector the water sprays are stronger and allow a higher washing performance.
After loading the appliance, make sure that the sprayer arms can rotate freely.

UNSUITABLE CROCKERY

  • Wooden crockery and cutlery.

  • Delicate decorated glasses, artistic handicraft and antique crockery.
    Their decorations are not resistant.

  • Parts in synthetic material which do not withstand high temperatures.

  • Copper and tin crockery.

  • Crockery soiled with ash, wax, lubricating grease or ink.
    The colours of glass decorations and aluminium/silver pieces can change and fade during the washing process. Some types of glass (e.g. crystal objects) can become opaque after a number of wash cycles too.

DAMAGE TO GLASS AND CROCKERY

  • Only use glasses and porcelain guaranteed by the manufacturer as dishwasher safe.
  • Use a delicate detergent suitable for crockery
  • Collect glasses and cutlery from the dishwasher as soon as the wash cycle is over.

TIPS ON ENERGY SAVING

  • When the household dishwasher is used according to the manufacturer’s instructions, washing tableware in a dishwasher usually consumes less energy and water than hand dishwashing.

  • In order to maximize dishwasher efficiency it is recommended to initiate the wash cycle once dishwasher is fully loaded.
    Loading the household dishwasher up to the capacity indicated by the manufacturer will contribute to energy and water savings. Information on correct loading of tableware can be found in Loading chapter.
    In case of partial loading it is recommended to use dedicated wash options if available (Half load/ Zone Wash, Multi Zone), fiilling up only selected racks. Incorrect loading or overloading the dishwasher may increase resources usage (such as water, energy and time, as well as increase noise level), reducing cleaning and drying performance.

  • Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended.

HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher please run a high temperature program at least one a month. Use a tea spoon of detergent and run it without the loading to clean your appliance.

CARE AND MAINTENANCE

CLEANING THE FILTER ASSEMBLY
Regularly clean the filter assembly so that the filters do not clog and that the waste water flows away correctly.

Using dishwasher with clogged filters or foreign objects inside filtration system or sprayarms may cause unit malfunction resulting in lose of performance, noisy work or higher resources usage.

The filter assembly consists of three filters which remove food residues from the washing water and then recirculate the water.

The dishwasher must not be used without filters or if the filter is loose.
At least once per month or after each 30 cycles, check the filter assembly and if necessary clean it thoroughly under running water, using a non- -metallic brush and following the instructions below:

  1. Turn the cylindrical filter A in an anti-clockwise direction and pull it out (Fig 1).
  2. Remove the cup filter B by exerting a slight pressure on the side flaps (Fig 2).
  3. Slide out the stainless-steel plate filter C (Fig 3).
  4. In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.) please remove them carefully.
  5. Inspect the trap and remove any food residues. NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).

FIG 11 CLEANING THE FILTER ASSEMBLY.JPG

After cleaning the filters, replace the filter assembly and fix it in position correctly; this is essential for maintaining the efficient operation of the dishwasher.

CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended period of time, let the water run to make sure it is clear and free of impurities before performing the necessary connections. If this precaution is not taken, the water inlet could become blocked and damage the dishwasher.

CLEANING THE SPRAY ARMS
On occasions, food residue may become encrusted onto the spray arms and block the holes used to spray the water. It is therefore recommended that you check the arms from time to time and clean them with a small non-metallic brush.

To remove the upper spray arm, turn the plastic locking ring in a clockwise direction. The upper spray arm should be replaced so that the side with the greater number of holes is facing upwards.

FIG 13 CLEANING THE SPRAY ARMS.JPG

The lower spray arm may be removed by pulling it upwards.

WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing scale buildup on heater, contributing also to better cleaning efficiency.

This system regenerates itself with salt, therefore it is required to refill salt container when empty.

Frequency of regeneration depends on water hardness level setting – regeneration takes place once per 6 Eco cycles with water hardness level set to 3.
Regeneration process starts in final rinse and finishes in drying phase, before cycle ends.

  • Single regeneration consumes: ~3.5L of water;
  • Takes up to 5 additional minutes for the cycle;
  • Consumes below 0.005kWh of energy.

TROUBLESHOOTING

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.

FIG 14 TROUBLESHOOTING.JPG

FIG 15 TROUBLESHOOTING.JPG

Policy and standard documentation and additional product information can be found by:

  • Visiting our website: docs.hotpoint.eu
  • Using QR Code
  • Alternatively, contact our After-sales Service (See phone number in the warranty booklet).

When contacting our After-sales Service, please state the codes provided on your product’s identification plate.

The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu (available only on certain models).

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals