LUCCA POR VENTWCE14 Ceiling Fan Instruction Manual
- June 12, 2024
- Lucca
Table of Contents
CEILING FAN INSTRUCTION MANUAL
Safety instructions
To reduce the occurrence of electric shock, the power cord is connected to the
The fan and disconnect switch must be installed at all poles (distance
The aperture of the switch contact is 3mm.
If you have electrical knowledge, be sure to keep your “electrician card”
Professional personnel will install it for you.
-
To avoid the risk of electric shock, install and disassemble the ceiling fan
Install before cutting off the power supply first. Must be grounded, live wire, command
The installation of the zero line must be disassembled to the zero line, live line Ground order. -
To reduce electric shock or accidents, do not use a regulator or Non local switch.
-
When installing the ceiling fan, different components need to be determined Screw locking.
-
When rotating the ceiling fan, the blades must not come into contact with any objects to avoid danger.
-
Choose a suitable location to install ceiling fans and blades
The distance between the ceiling fan and the ground must be at least 2.3 meters. -
To change the direction of rotation of the fan, please turn off the fan and wait for the blades Stop rotating after adjusting the frequency converter.
-
The power of this machine is 120v/60hz, and the maximum power of the motor is 60w (Specifications and models of ceiling fans, including motor power) Each light source will have a maximum of 40W, depending on the difference.
-
Regarding how to install the ceiling fan and connect the power supply, please read Carefully check the assembly procedure of the fan.
-
Do not clean the ceiling fan blades, directly use water or clean them Detergent, wipe with a dry or slightly damp clothDust. Before cleaning the ceiling fan, it must be Turn off the power switch.
Required tools
- Cross screwdriver
- Flat head screwdriver
- Adjustable clamp or wrench
- Stairs
- Wire cutting machine
- Electrical tape
Installation tools
- Cross screwdriver
- Flat head screwdriver
- Adjustable clamp or wrench
- Stairs
- Wire cutting machine
- Electrical tape
- Impact drill
Part Control
| NO. | Name | Quantity | NO. | Name | Quantity |
|---|---|---|---|---|---|
| 1 | Hanger support | 1 | 10 | Light source | 2 |
| 2 | 5-inch rod | 1 | 11 | Translucent lampshade | 1 |
| 3 | 1 lunging bell | 1 | 12 | Fan blade | 3 |
| 4 | Horn hood | 1 | 13 | Spare parts kit | 4 |
| 5 | Remote control | 1 | 14 | Blade screw | 6 |
| 6 | Engine casing | 1 | 15 | Balancing package | 4 |
| 7 | Motor | 1 | |||
| 8 | Circular disk | 1 | |||
| 9 | Chassis lampshade | 1 |
- Install the arrow, ball, clock, and horn cover
Remove the arrow. Thread the wiring block, bell, and horn decorative cover
through the arrows.
(Pay attention to the direction of the horn and the decorative cover of the
horn)
Insert the arrow into the lifting head, rotate the arrow to align it with the
empty position, insert the long pin and locking pin, and lock the anti
buffering screw.
Silicone ring hanging from the edge of the clock diameter (Figure 3)
Hanger installation
-
Fix wooden brackets or ceilings with wooden screws.
-
To use expansion bolts on the flap bracket of the concrete ceiling, an 8mm diameter expansion bolt needs to be drilled.
Installing the blade
Install the fan blades on the motor in sequence and tighten the screws on the fan blades in sequence.
Lamp installation
- Connect the corresponding wires to the bottom of the lamp and motor.
- Tighten the three screws on the sunroof frame
- Light source installation and torsion direction view
- Install the lamp cover in place.
Installation height
Install the lifting ball on the hanger
Place the lifting ball into the hanger and rotate it to secure the groove at the joint of the lifting top (in the hanger).
Advice:
Please strictly follow
Specify light source parameter link On the label. Otherwise, it will directly
affect the lifespan of the switch or cause immediate failure of the switch.
| Fan receiver parameters | At temperature function | 40°C (Domestic) |
|---|---|---|
| Dimension | 1155025mm | Temperature. Function |
| function | AC150-240V | result Voltage |
| frequency work | 50/60HZ | power output |
One sentence!!! Do not operate with power during installation, and the wiring should be installed according to national electrical standards.
- LED indicator light
- Lighting Switch
- Fan 1 speed
- Fan speed 2
- 3-speed fan
- Fan off
- Fan synchronization
- AAA-12V-23A (1category)
| Remote control Fan | At temperature function | -50 ° C -40 ° C inside |
|---|---|---|
| Dimension | 1166019mm | Temperature. Function |
| Voltage function | AAA-12V-23A(1 Section) | Online loans electric current |
| frequency at work | 433.92M (±75K) | distance Launch. |
degrees)
Advice:
When the transmitter is unable to remotely control the receiver. Please check
if the switch battery contacts are normal. If the positive and negative
electrodes are placed correctly. Is there enough energy? (If the light is
dimmed; replace the battery) When the transmitter is unable to remotely
control the receiver. Please check if there are remote control products with
the same frequency nearby. And check if the transmitter button is pressed, as
simultaneous transmission of remote control products of the same frequency can
cause interference and affect the effectiveness of receiving poor commands. If
the remote control function is excluded, it will return to normal.
3. When using this product, do not place it in a place where children can
play.
4. This product has a fan power-off memory function, and the last fan
direction will automatically start the next time.
5. Code learning operation: Start the machine for 1 minute, press and hold
the “1 hour” key to turn on the indicator light, and the receiver will send
out the code learning successful A beep.
6. When the remote control cannot be effectively controlled: Please check the
battery and remove it when not in use for a long time.
Inserting the power cord
A:DC
Locking cables and grounding wires
- Loosen the expansion screw, tighten the steel wire rope, and tighten the screw to fix the steel wire rope.
- Lock the input power grounding wire, lifting head grounding wire, and receiver grounding wire onto the hanger.
Fan balance adjustment
The fan has been installed. If it vibrates from top to bottom, please check
the screws
If the blade, suspension rod, and lamp kit are fixed, if not, please fix them
Use a screwdriver. If you are still trembling, please use the stool in the
balance kit
And check the balance kit instructions inside the cardboard box.
Tip: Maintenance of ceiling fans
- As the ceiling fan is still working, please regularly check if the hanger, fan blades, wallet and other components are loose. If they are not loose, please fix them in a timely manner to ensure the safe operation of the ceiling fan.
- Regularly keep the ceiling fan clean. Only use a soft brush or lint free cloth to gently clean. Do not use damp cloth or other destructive cleaning agents.
- Do not add lubricating oil or lubricants to any part of this product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>