ALTA 15 Channel Remote Control User Guide

June 12, 2024
ALTA

15 Channel Remote Control

Product Information:

The product is a motorized control system that allows users to
remotely control various functions. It comes with a remote control
that can be paired with the motor to operate different actions. The
system also allows for adjusting the motor speed and setting upper
and lower limits. The product is powered by a battery and can be
charged using an AC adapter or solar panel.

Product Usage Instructions:

Adding a Remote Control:

  1. On the current remote control, press one P2 button until the
    motor jogs x1 and beeps x1.

  2. Once more, on the current remote control, press one P2 button
    until the motor jogs x1 and beeps x1.

  3. On the new remote control, press one P2 button until the motor
    jogs x2 and beeps x3.

*Repeat the same procedure to add/remove additional remote
controls.

Adjusting the Motor Speed:

To increase the motor speed:

  1. Press one P2 button until the motor jogs x1 and beeps x1.
  2. Press the Up button until the motor jogs x1 and beeps x1.
  3. Once more, press the Up button until the motor jogs x2 and
    beeps x1.

*If the motor has no response, it already has a maximum or
minimum speed.

To decrease the motor speed:

  1. Press one P2 button until the motor jogs x1 and beeps x1.

  2. Press the Down button until the motor jogs x1 and beeps
    x1.

  3. Once more, press the Down button until the motor jogs x2 and
    beeps x1.

*If the motor has no response, it already has a maximum or
minimum speed.

Other Functions:

The product also offers additional functions such as
pairing/unpairing remote control, switching rotating direction,
setting upper/lower limits, adding/removing favorite positions, and
switching roller/sheer mode. Please refer to the Quick Index in the
user manual for detailed steps on these functions.

Troubleshooting:

If you encounter any issues with the motor, refer to the
troubleshooting section in the user manual. Some common problems
include no motor response and beeping during use. The manual
provides possible causes and solutions for these problems.

GETTING STARTED – continued

7. ADDING A REMOTE CONTROL

USING AN EXISTING

REMOTE CONTROL

a.

a. On the current remote

Action on Remote

control, press one “P2”

Control

button until motor jogs x1

and beeps x1.

Motor

b. Once more, on the

Response

current remote control,

press one “P2” button

until motor jogs x1 and

beeps x1.

Action on c.

c. On the New remote control, press one “P2”

Remote Control

button until motor jogs x2

and beeps x3.

Motor

Response

Current Remote Control P2
Jog x1 Beep x1
NEW Remote Control P2
Jog x2 Beep x3

Current Remote Control b. P2
Jog x1 Beep x1

*Repeat the same procedure to add/remove additional remote control.
PROGRAMMING A NEW REMOTE CONTROL Follow instructions under the section 1. Pair / Unpair Remote Control

8. ADJUSTING THE MOTOR SPEED

INCREASE MOTOR

Action on a. P2

b.

SPEED

Remote

Control

a. Press one “P2” button until motor jog x1 and beep x1.

Motor Response

Jog x1 Beep x1

Action on c.

b. Press “Up” button until Remote motor jog x1 and beep x1. Control

Up

c. Once more, press “Up” button until motor jog x2 and beep x1.

Motor Response

Jog x2 Beep x1

Up
Jog x1 Beep x1

*If the motor has no response, it already has a Maximum or Minimum speed.

DECREASE MOTOR SPEED
a. Press one “P2” button until motor jogs x1 and beeps x1.
b. Press “Down” button until motor jogs x1 and beeps x1.
c. Once more, press “Down” button until motor jogs x2 and beeps x1.

Action on Remote Control

a. P2

b. Down

Motor Response

Jog x1 Beep x1

Action on c.

Remote Control

Down

Motor Response

Jog x2 Beep x1

Jog x1 Beep x1

*If the motor has no response, it already has a Maximum or Minimum speed.

QUICK INDEX

SETTINGS

STEPS

1. Pairing

P1 (hold for 2s) > Stop (hold for 2s)

Switch Rotating Direction

Set Upper/Lower Limits

Up + Down (hold for 2s)
Upper Limit: Up (hold for 2s) > Up + Stop (hold for 2s)
Lower Limit: Down (hold for 2s) > Down + Stop (hold for 2s)

Add/Remove 4. Favorite
Position

P2 > Stop > Stop

Roller/Sheer Switch

Mode

Up + Down (hold for 5s)

Stop

Adjusting Limits

the

Upper: Up + Stop (hold for 5s) > Up or Dn > Up + Stop (hold for 2s)
Lower: Dn + Stop (hold for 5s) > Up or Dn > Dn + Stop (hold for 2s)

Add/Remove Remote

a

P2 (existing) > P2 (existing) > P2 (new)

Increase Motor Speed: P2 > Up > Up 8. Speed Regulation
Decrease Motor Speed: P2 > Down > Down

DECLARATIONS
U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada license- exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

TROUBLESHOOTING

PROBLEM – THE MOTOR HAS NO RESPONSE

Cause Battery in motor is depleted
Insufficient charging from Solar Panel

Solution Recharge with compatible AC adaptor and check connection and positioning of solar panel Check connection and orientation of solar panel

Remote control battery is discharged or Replace battery or check placement. not installed properly

Radio interference / shielding

Ensure remote control and the antenna on the motor are positioned away from metal objects

Receiver distance is too far

Move the remote control to a closer position.

Power failure

Check power supply to motor is connected/active.

Incorrect wiring

Check that wiring is connected correctly.

PROBLEM – THE MOTOR BEEPS 10 TIMES WHEN IN USE

Cause Battery voltage is low/ SolarPanel Issue

Solution Recharge with AC adapter or check connection and positioning of solar PV panel

PROBLEM – THE MOTOR WILL NOT PROGRAM OR CONNECT

Cause Check if the motor in Sleep Mode
Multiple Motors are paired to the same

Solution Press the P1 button on the motor for 2 seconds to activate Pairing Mode.
Always reserve a channel for programming. To work on a single motor at a time, place all other motorsinto sleep mode. Press the “P1” button (about 6 ec) on the motor head until motor jogs x2 and beeps x2.

SAFETY INSTRUCTIONS
1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor. 3. Do not cut the antenna. Keep it clear from metal objects. 4. Do not allow children to play with this device. 5. If the power cable or connector is damaged, do not use. 6. Ensure the power cable and antenna are clear and protected from
moving parts. 7. Cable routed through walls should be properly isolated. 8. Motor should be mounted in horizontal position only. 9. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.

Declarations

AMP25B

Add A zoom in on the charging port

FCC Text – text 01

Roller Sheer Revolve Roman shades

, sheer shadings, roman shades, and zebra shades.

P1

AMP25B AMP25B

Add visual explanation of P1 – file 02

Safety
Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately.

BLISSTMAutomation by Alta

15 CHANNEL REMOTE CONTROL
PROGRAMMING AND USERS GUIDE
Scan QR code to view additional BLISSTM Automation Programming Guides
Scan QR code to watch BLISSTM Automation Programming Videos

SPECIFICATIONS
Voltage Radio Frequency Transmitting Power Operating Temperature RF Modulation Lock Function IP Rating Transmission Distance

3V (CR2450) 433.92 MHz Bi-directional 10 milliwatt 14°F to 122°F (-10°C to 50°C) FSK Yes IP20 up to 200m (outdoor)
Revised 3/2022

REMOTE CONTROL OVERVIEW
Please read prior to installation and use. Save these instructions for future reference.
BUTTON INSTRUCTIONS

Lower Channel

LCD Display

Up

Stop

P2

Down

Higher Channel

P2
Lock Switch

P1 BUTTON LOCATION

HORIZONTAL BLIND
TILT MOTOR

ROLLER / SHEER DUAL / WOVEN
MOTOR

HONEYCOMB SHADES MOTOR

P1 Button

Power line
LED light

P1 button Lithium Battery Switch

Signal line

P1 Button

REPLACING THE BATTERY
a. Gently insert the included a. ejector tool into the pinhole opening and apply a small amount of pressure to the cover and slide the cover off.
b. Install battery (CR2450) with positive (+) side facing up.
c. Gently slide the cover back until a “click” sound is heard.

b.
Battery (CR2450)

c. “click”

ADVANCED SETTING – DISABLE LIMIT SETTING

a. Remove the cover from the backside of remote, the lock switch is in the right corner.
b. Move the switch to the “Lock” position to disable the following commands, remote will show “L” (lock):
– Change Motor Direction – Setting the Upper and Lower Limit – Adjust Limit – Roller Mode or Sheer Mode
c. Move the switch to “Unlock” position to assess all remote functions, remote will show “U” (unlock).
*This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits.

a.
b. Unlock Lock Switch
c. Unlock Lock Switch

Switch
L U

CHANNEL OPTIONS

SELECT A CHANNEL

a. Press “<” button on the remote to select a lower channel.
b. Press “>” button on the remote to select a higher channel.

Action on a.

Remote Control

Lower Channel

Remote

1

Response

b.
Higher Channel
15

HIDE UNUSED CHANNELS
a. Press and Hold (about 3 sec) “<” and “>” buttons simultaneously until remote control displays “C” (channel).

Action on a. Remote Control
Remote Response

b. Press “<” or “>” button to select required quantity of channel (between 1 to

Action on b. Remote Control

15).

Remote

c. Press “Stop” button

Response

to confirm selection (the

Action on c.

example shows a 5-channel Remote

selection). The LED will

Control

display “O” (OK) once to confirm selection.

Remote Response

Lower

Higher

Channel Channel

C

or

Lower

Higher

Channel Channel

11

Stop

5

O

GETTING STARTED
It is important to confim that the motor is awake and ready to receive programming. To do this, press “P1” button on the motor less than 1 sec, to activate the motor from Sleep Mode.

1. PAIR / UNPAIR REMOTE CONTROL

NOTE: Honeycomb and Horizontal Blind Motors DO NOT BEEP.

a. Press “P1” button (about 2 sec) on the motor head until motor jogs x1 and beeps x1.
b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jogs x2 and beeps x3
.

Action on a. P1 P1 Motor

Motor Response

Jog x1

Action on b. Remote Control
Motor Response

Stop
Jog x2

  • Repeat the same procedure to unpair remote control.

Beep x1 Beep x3

2. CHANGE MOTOR DIRECTION (IF NECESSARY)
This operation is only valid when no limits have been set. If the motor has the upper and lower limits set, you can only switch direction by pressing “P1” button (about 10 sec) on the motor head until motor jog x3 and beep x3.

Press “Up” or “Down” button to check if the shade moves in the desired direction.
If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jogs x1 and beeps x1.

Action on Remote Control
Motor Response

Up

Down

Jog x1

Beep x1

3. SETTING THE UPPER AND LOWER LIMITS

SET UPPER LIMIT

a. Press “Up” button to

Action on a.

raise the shade, then press Remote “Stop” button when it is in Control

Up

the desired upper limit.

Motor

b. Press and hold (about

Response

5 sec) “Up” and “Stop”

buttons simultaneously

until motor jogs x2 and

beeps x3.

b. Up

+ Stop

Jog x2

Beep x3

SET LOWER LIMIT
a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.

Action on Remote Control
Motor Response

a. Down

b.

Down

Stop

Jog x2

Beep x3

b. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jogs x2 and beeps x3.
*If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

4. ADJUST LIMITS

ADJUST THE UPPER LIMIT Action on

Remote

a. Press and hold (about

Control

a. Up

+ Stop

5 sec) “Up” and “Stop”

Motor

Jog x1

Beep x1

buttons simultaneously

Response

until motor jogs x1 and

beeps x1.

b. Use “Up” button to raise the shade to the desired

Action on Remote Control

c.

Up

+ Stop

highest position, and use “Up” or “Down” button to do the final adjustment if

Motor Response

Jog x2

Beep x3

necessary.

b. Up

c. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jogs x2 and beeps x3.

ADJUST THE LOWER LIMIT
a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jogs x1 and beeps x1.
b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.

Action on Remote Control Motor Response
Action on Remote Control Motor Response

a.

Down

Stop

Jog x1

Beep x1

c.

Down

Stop

Jog x2

Beep x3

b. Down

c. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jogs x2 and beeps x3.

5. FAVORITE POSITION

SET A FAVORITE POSITION

a. Use “Up” or “Down” button to move the shade to desired Favorite position.

Action on Remote Control

a.
or

b. P2

Up

Down

b. Press and hold one “P2” button on the back of remote

Motor Response

or

control until motor jogs x1 and

beeps x1.

Jog x1 Beep x1

c. Press and hold “Stop” button until motor jogs x1 and beeps x1.

d. Once more, press “Stop” button until motor jogs x2 and beeps x3.

Action on Remote Control
Motor Response

c. Stop

d. Stop

Jog x1 Beep x1

Jog x2 Beep x3

USING A FAVORITE POSITION Action on

Remote

Stop

Press and hold (about 2 sec)

Control

“Stop” button, motor will move Shade

or

to Favorite position.

Response

REMOVE A FAVORITE POSITION
a. Press one “P2” button until motor jogs and beeps x1.
b. Press (about 2 sec) “Stop” button until motor jogs and beeps x1.
c. Once more, press “Stop” button until motor jogs x1 and long beep x1.

Action on a. Remote Control
Motor Response

P2
Jog x1 Beep x1

b. Stop
Jog x1 Beep x1

Action on Remote Control
Motor Response

c. Stop

Jog x1

Beep x1

6. HOW TO TOGGLE FROM ROLLER MODE / SHEER MODE

ROLLER SHADE MODE – Default mode, allows for continuous raising/lowering of shade after a short press
a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jogs x1.
b. Press and hold (about 2 sec) “Stop” button until motor jogs x2 and beeps x3.

Action on Remote Control
Motor Response
Action on Remote Control
Motor Response

a.

Up

Down

Jog x1

b. Stop

Jog x2

Beep x3

For precise control and adjustment, use Sheer Shade Mode.

SHEER SHADE MODE – Allows for slight adjustment after a short press and raising/ lowering of shade after a longer press

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.

Action on Remote Control
Motor Response
Action on Remote Control Motor Response

a. Up

+ Down

Jog x1

b. Stop

Jog x1

Beep x1

Continue on to step 7.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals