ICStation GY21088-1 Wooden FM Radio Music Player DIY Kit Installation Guide

ICStation GY21088-1 Wooden FM Radio Music Player DIY Kit Installation Guide

Introduction

It is a FM Radio Amplifier Mono FM Music Player Handmade Wooden Assembly Experimental Equipment. It uses a wooden casing to create a very primitive FMradio. It can play music from FM radio with the 3W 4ohm speaker produce clear and loud sound. The use of screws for fixation makes installation very convenient and simple.

Feature

1. Pure wooden shell board
2. FM Audio Player with built-in power amplifier
3. Adjustable Radio Station and Volume
4. Single Channel Mono Speaker

Parameter

1. Product Name: Wooden FM Radio Music Player DIY Kit
2. Work Voltage: DC 3V
3. Speaker: 3W 4ohm
4. Channel: Single-Channel Mono
5. Audio source: FM
6. Receiver Frequency: 88.0MHz~108.0MHz
7. Control Type: On Board Button
8. Output type: Speaker
9. Power Type: AA*2 Battery
10. Work Temperature:- 20℃~85℃
11. Work Humidity: 5%~85%RH
12. Size(Installed): 1177340mm

Package

• FM Radio Receiver Module x1
• Wooden Boards x4
• 3W 4ohm Speaker x1
• AA*2 Battery Box x1
• FM Antenna x1
• Black Sponge Base x4
• Double-Sided Tape x1
• M2*10mm Screw x3
• M2*7mm Screw x11
• M2*6mm Screw x2
• M2*4mm Screw x6
• Screwdriver x1
• Transparent Plastic Box x1

Installation Steps(Please be patient)

1 >.Step 1: Remove all available boards from the 4 wooden boards. Be careful not todamage the wooden board. 2 >.Step 2: Fix 1pcs 3W 4ohm Speaker on Wooden Board by 4pcs M24mmScrew.
3 >.Step 3: Paste double-sided adhesive on the back of the FM Radio Receiver Module. 4>.
Step 4: Paste and fix FM Radio Receiver Module on another Wooden Board by 4pcsM27mm Screw. Note:Loosen the screws slightly and do not tighten themtoo tightly.
5 >.Step 5: Fix 1pcs AA2 Battery Box on another Wooden Board by 2pcs M24mmScrew.
6 >.Step 6: Splicing wooden boards from battery box and FM receiver. Connect the battery socket while placing the wires in the wiring slot.
7 >.Step 7: Fix FM Antenna gasket by by 2pcs M2*6mm Screw. 8 >
.Step 8: Fix FM Antenna and gasket from FM Radio Receiver Module by 1pcs
M2*7mm Screw. 9 >.Step 9: Insert fixed small bracket. 10>.Step 10: Connect the 3W 4ohm Speaker to FM Radio Receiver Module. 11 >.Step 11:* Splicing wooden boards from FM receiver and speaker. 12>.Step 12: Fix TOP wooden board by 2pcs M27mm Screw. Note: Align each
installation hole. 13 >.Step 13: Slowly bend the wooden board to avoid breaking and then fix by 2pcs
M2*10mm Screw. 14 >.Step 14: Fix Bottom wooden board by 2pcs M2*7mm Screw. 15>.Step 15: Slowly bend the wooden board to avoid breaking and then fix by 1pcs
*M210mm Screw. 16 >.Step 16: Install 2pcs AA Battery. 17>.Step 17: Fix the last wooden board by 1pcs M27mm Screw. 18 >.Step 18: Slowly bend the wooden board to avoid breaking and then fix by 1pcs
M27mm Screw. 19 >.Step 19: Install 4pcs Black Sponge Base on Bottom wooden board

‘Step 2: Fix 1pcs 3W 4ohm Speaker on Wooden Board by 4pcs M2*4mm Screw.

Step 3: Paste double-sided adhesive on the back of the FM Radio Receiver Module.

Step 4: Paste and fix FM Radio Receiver Module on another Wooden Board by 4pcs M2*7mm Screw.
Note: Loosen the screws slightly and do not tighten them too tightly.

Step 5: Fix 1 pcs AA*2 Battery Box on another Wooden Board by 2pcs M2`4mm Screw

Step 6: Splicing wooden boards from battery box and FM receiver. Connect the battery socket while placing the wires in the wiring slot.

Step 7: Fix FM Antenna gasket by by 2pcs M2’6mm Screw.

Step 8: Fix FM Antenna and gasket from FM Radio Receiver Module by 1pcs M2*7mm Screw. 1! III

Step 9: Insert fixed small bracket.

Step 10: Connect the 3W 4ohm Speaker to FM Radio Receiver Module.

Step 11: Splicing wooden boards from FM receiver and speaker.

Step 12: Fix TOP wooden board by 2pcs M2*7mm Screw. Note: Align each installation hole.

Step 13: Slowly bend the wooden board to avoid breaking and then fix by 2pcs MrlOmm Screw.

Step 14: Fix Bottom wooden board by 2pcs M2 7mm Screw.

Step 15: Slowly bend the wooden board to avoid breaking and then fix by loos MTIOmm Screw.

Step 16: Install 2pcs AA Battery.

Step 17: Fix the last wooden board by 1pcs M2*7mm Screw.

Step 18: Slowly bend the wooden board to avoid breaking and then fix by 1pcs Mr7mm Screw.

Step 19: Install 4pcs Black Sponge Base on Bottom wooden board.

References

• ICStation Developing and Providing Worldwide With IC Accessories, Raspberry Pi, Robots, Arduino compatible Dev. Board and Modules
• ICStation Developing and Providing Worldwide With IC Accessories, Raspberry Pi, Robots, Arduino compatible Dev. Board and Modules

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>