igoohome Keybox 3 User Guide

igoohome Keybox 3

Welcome!

This guide will get you up and running with your igloohome Keybox 3. In the meantime, you should follow igloohome on Facebook and YouTube!

As our igloohome app is frequently updated, there may be changes to this manual.
Please refer to our websiteigloohome.co/support for the latest version of the manual.

What’s Included

Specifications

* DO NOT USE: Heavy Duty, Eveready, GP, or rechargeable batteries. Duracell & Energizer alkaline batteries recommended. Please note that using better batteries will improve the performance and lifespan of the lock.

Features

PIN / Bluetooth Unlock

Master PIN Code
The igloohome Keybox 3 unlocks with a permanent Master PIN Code.

User PIN Code
The igloohome mobile app can generate multiple types of User Pin codes, e.g. One-Time, Permanent & Duration.

Bluetooth Master Key
The igloohome Keybox 3 unlocks with Bluetooth via the app.

Bluetooth Guest Key
The igloohome mobile app can generate and share Bluetooth keys based on duration with guests to unlock the Keybox 3.

Battery

Battery Life
The Keybox 3 can last up to 12 months with 4 AAA Alkaline battery

Emergency Jump Start
If battery power is drained, connect a USB-A to USB-C cable to a power bank then plug it onto the USB-C jumpstart port on the keybox to provide emergency power.

Low Battery Indicator
The Status Indicator shows red light when battery level is 20% and below, followed by a sound alert when the keypad is woken up. The battery level can also be monitored on the app and is updated during Bluetooth Unlock.

Security

Keypad Security Lockout
Lock will disallow any PIN entries and sound an alarm when there is a number of incorrect PIN attempt. User can configure number of incorrect attempts to trigger timeout.

Auto Relock
The Keybox 3 relocks automatically when product is closed. User can deactivate auto-relock function if they prefer manual relock.

Masking Security Code
A total of 16 digits including the masking digits can be entered to prevent the PIN code from being exposed.

Weather Resistant
The Keybox 3 is able to withstand weather conditions with protection against dust and water (IP66)

Quick Start Guide

1. Loosen the 4 screws and remove battery cover
   

2. Insert AAA Batteries
   

3. Secure battery cover tightly with 4 screws
   

Please screw the battery cover tightly after inserting batteries to ensure optimal water resistance.

App Onboarding

Test Factory PIN Unlock

In the factory mode (before pairing), the PIN to unlock the lock is 1 2 3 4 5 6 7 8 9 0

Register as a Lock User

a) Download igloohome from the App Store / Play Store
b) Create an account and login

Pairing

a) Select [Add new igloohome lock]
Note: For existing users with other paired locks, go to [Configuration], select [Add Locks] and follow the instructions.

**Setting Master PIN Code

**

Before proceeding, turn on your Bluetooth and ensure that you are within Bluetooth range of the lock.
Go to [Access] and customize your [Master PIN] by editing it.

Managing Access in App

Creating PIN codes

PIN codes can be generated on the app under [Access], press [+Access] and choose either One-Time, Permanent or Duration PIN.
Pin codes will expire if its not use within its activation period. Refer to the table below.

PIN Type

|

Use PIN **within***

---|---

Permanent PIN

|

24 hrs of generation

One-Time PIN

|

24hrs of generation

Duration PIN

|

24hrs from the start time

Note: Duration PIN code end times can be customized within a 28-day timeframe. Past this timeframe, the end time will automatically be configured to the start time.

Bluetooth Guest Key

Bluetooth Guest Key can be shared with other users for mobile access. It allows your guests to unlock the igloohome smart lock via Bluetooth.

There are 3 steps to using a Shared Bluetooth Key

1. Under [Access], press [+Access] and choose [Bluetooth Key] under
   [Access Type]. Proceed to share the key after it is created.

2. Guest receives the Bluetooth Key by one of these methods:
   • Clicking the URL given and follow the instructions.
   • Claiming Bluetooth Key under [Configuration].

3. Guest can now use the Bluetooth Key under the Guest Bluetooth Key Section whenever he/she is within range of the lock.
   Notes:
   • The owner can revoke the Bluetooth Key in App.
   • Bluetooth Key must be accepted within 1 hour generation before it expires.

Unlocking

Bluetooth Unlock

1. Open your igloohome app
   

2. Tap on the “Bluetooth Unlock” button
   

3. The status indicator will flash green twice with 4 short ascending tone once unlocked.
   

PIN Code

1. Press any button on the keypad to wake device up
   

2. Key in a valid PIN code (with or without masking pins) followed by the “Unlock Icon”
   

3. The status indicator will flash green twice with 4 short ascending tone once unlocked.
   

Locking

Auto Relock

Simple close the keybox in place and Status Indicator will show green with a long beep.

Manual Relock

Press and hold the Unlock icon on the bottom right of the keypad for 2 seconds until the status indicator will show green with a long beep.

Note: Used when Auto Relock is “Off”

Lock Installation

Secure Keybox on a handle or knob

1. Unlock the keybox
   

2. Push the shackle release to the right
   

3. Pull out the shackle
   

4. Secure on a handle or knob
   

5. Insert back the shackle
   

Mount on a surface

1.  Unlock the keybox
   

2. Drill holes on a wall
   

3. Hammer the screw anchors into the holes

4. Mount the Keybox 3 on the wall with the mounting seal rings and 2 screws
   

Lock Behaviour

Note: User is able to Enable and Disable Keypad Security Lockout via Bluetooth.

 |

Keypad Security Lockout

---|---

Triggered by

|

5 consecutive PIN Code attempts by default (Configurable via Bluetooth)

Disable By

|

After 1 / 5 / 10 Minutes or Master / Guest Bluetooth Unlock

Behaviour

|

Single flash White LED on keypad and Red LED on status indicator when keypad is triggered.

Duration

|

Please refer to table below.

Triggered

| Security Alarm|

Keypad Lockout

---|---|---

1st Time

| 30 Sec|

1 Min

2nd Time

| 60 Sec|

5 Min

3rd and Consecutive Time

| 90 Sec|

10 Min

USB-C Jumpstart

USB-C Jumpstart Feature

1. Connect the USB-A to USB-C cable to a power bank then plug it onto the USB-C jumpstart port on the keybox.
2. While the USB-A to USB-C cable is connected to the power bank, key in PIN code on the keypad followed by to unlock.
   

Please unlock by entering a valid PIN code or via the app within 20 seconds after the keybox is powered up.

Audio and LED Indications

LED 2 times
Successfully Locked| 1 long beep after product is locked and Green LED for 2 seconds
Incorrect PIN| 4 short beeps and flash Red 2 times
Deleted PIN| 3 sets of 4 short beeps and flash Red 2 times
Obstruction Alarm| 6 sets of 4 short beeps
Security Lockout Alarm| Low – High siren for 30 / 60 / 90 seconds
Security Lockout Deactivated| 2 long beeps
Low Battery Alert| Descending 3 fast tones when keypad is woken up and breathing Red LED
Hard Reset / Unpair| Descending 4 slow tones
Power Start Up| 2 slow beeps then 2 quick beeps

Troubleshoot

I am unable to close the keybox.|

• Do an unlock via PIN code or Bluetooth and try to close the keybox again.
• Note that you might accidentally lock the keybox manually by holding the UNLOCK button for 2 seconds when the keybox is open.

---|---
I am unable to remove the battery cover screws.|

• Note that the screws are designed to be retained, therefore cannot be removed.
• Please loosen the screws to remove the battery cover.

The keybox keypad flashes white and LED indicator flashes red when I activate the keypad.|

• Keypad Security Lockout is triggered on the Keybox.
• Please refer to page 15.

I tried to use USB-C to jumpstart the lock but unable to.|

• Please ensure USB-C connector is connected to the USB-C slot securely while unlocking it with PIN code or Bluetooth.
• Please unlock within 20 seconds.
• Please ensure that the Power Bank has sufficient power.

The lock is not responding at all.|

• The Keybox’s battery is flat.
• Use an USB-A to USB-C cable connected to a power bank to jumpstart the lock and unlock the keybox to replace the batteries.
• Please unlock within 20 seconds.
• Refer above to know how to replace batteries.

I closed the Keybox but it did not relock automatically.|

• Make sure Auto Relock is ON via the igloohome mobile app.
• If Auto Relock is ON and the keybox is still not working, try to lock the keybox manually by holding the UNLOCK button for 2 seconds

I tried to unlock the Keybox but the keypad went off and came back on with 2 slow and 2 quick beeps.|

• The Keybox is low in battery.
• Use an USB-A to USB-C cable connected to a power bank to jumpstart the lock and unlock the Keybox to replace the batteries.
• Refer above to know how to replace batteries.

I can’t scan the QR sticker as it is warned out.|

• Use the spare QR sticker that is provided in the Keybox box.

I have generated my PINs from the app but it cannot work.|

• Do a Bluetooth Unlock or sync and try again.
• Make sure that the generated PIN codes are activated within the activation period before it expired.

For enquiries go to:
igloohome.co/support

Documents / Resources

| igoohome Keybox 3 [pdf] User Guide
Keybox 3
---|---

References

• Support | igloohome Support & Help Portal

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>