Antari LCU-2S Liquid Supply System User Manual
- June 4, 2024
- Antari
Table of Contents
Antari LCU-2S Liquid Supply System User Manual
Safety Information
| Please read the following safety information carefully before operating the
machine. This information includes important safeguards about installation,
usage, and maintenance. Pay attention to all warning labels and instructions
in this manual and printed on the machine.
---|---
If you have questions about how to operate the machine safely, please contact your local Antari dealer for help.
- Keep this device dry.
- Always connect to a grounded circuit to avoid risk of electrocution.
- Before connecting the machine to power, always check the voltage indicated on the machine matches to your local AC voltage. Do not use the machine if AC power voltage does not match.
- Disconnect the machine from AC power before servicing and when not in use.
- This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local Antari dealer for advice.
- No user serviceable and modifiable parts inside. Never try to repair this product, an unauthorized technician may cause damage or malfunction to the machine.
- For adult use only. Never leave the machine running unattended.
- Never add flammable liquid of any kind to the machine.
- Make sure there are no flammable materials close to the machine while operating.
- Only use Antari fluid. Other fluid may lead to machine malfunction.
- If the machine fails to work, unplug the machine and stop operation immediately. Contact your local Antari dealer for advice.
- Before transporting the machine, make sure the fluid tank is completely drained.
- Fog/Snow fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely. In case of eye contact or if fluid is swallowed, immediately look for medicaladvice.
Unpacking and Inspection
Immediately upon receiving the machine, carefully unpack the carton, check the content to ensure that all parts are present and have been received in good condition. If any parts appear damaged or mishandled from shipping, notify the shipper immediately and retain the packing material for inspection.
What is included
- 1 x LCU-2S Liquid Supply Unit
- 1 x LCU-2S Liquid Tank Unit
- 1 x Power Cord
- 1 x 3 Pin Data Connection Cable
- 1 x 6mm Fluid Tube
- 1 x 4mm Fluid Tube
- 3 x 4 to 4mm adaptor
- 3 x 6 to 4mm adaptor
- 1 x Fluid Filter
- 1 x User Manual
Product Dimensions
Product Overview
Setup and Installation
Fluid Connection
Use supplied 6mm tube for external tank and connection between supply unit and
tank unit.
Fit supplied fluid filter to the tube place in external tank to prevent
obstacle entering the fluid line. From tank to machine use supplied 4mm tube
and adaptor if extension is required.
Important
– Machine is equipped with over temperature protection, when machine exceed
its temperature limit it will be automatically shut down until it reaches safe
operating temperature.
– The max vertical distance between the LCU-2S supply unit (pump) and LCU-2S
liquid tank unit can be up to 12 meters while the max horizontal distance can
reach 35 meters
Data Connection
For data connection 3-pin connector is used. Connect the output of control
unit with input of tank unit.
Service and Maintenance
- Do not allow the machine to become contaminated.
- Only use a damp cloth to clean the casing.
- It is recommended to run the machine on a monthly basis in order to achieve best performance and output condition.
Fuse Replacement
| Disconnect AC power before replacing fuse. Only replace fuse with same type
and rating.
---|---
Step 1: Disconnect power cord from supply.
Step 2: Use a flat-head screwdriver to release fuse holder.
Step 3: Replace fuse with exact same type and rating as indicated below.
Step 4: Reinsert fuse holder.
Fuse
120V = T0.8A 250V
230V = T0.8A 250V
Technical Specifications
– Input voltage| US model : AC 100-120V, 50 / 60Hz 0.35A EU model : AC
220-240V, 50 / 60Hz 0.18A
---|---
– Rated power| 48W
– Compatible fluid| Antari Fluid
– Ambient temp. range| 5 °C – 40 °C (41 °F-104 °F)
– Control| Auto
– Connection| IEC (Power) XLR 3-pin (Data)
– Dimension| Supply unit L179 W167 H84 mm (L7.05 W6.57 H3.31 inch) Tank unit
L158 W103 H248 mm (L6.22 W4.06 H9.76 inch)
– Weight| Supply unit 1.95 kg (4.30 lbs) Tank unit 1.8 kg (3.97 lb
For current product information visit Antari at
:www.antari.com
For information requests please contact us
at:sales@antari.com
|
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>