Antari Z-1520 RGB Fog Machine User Manual

: June 4, 2024
: Antari

Table of Contents

Safety Information
Unpacking and Inspection
Product Dimensions
Product Overview
Operation
Service and Maintenance
Technical Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Z-1520 RGB
Fog Machine
User Manual

Safety Information

**** Please read the following safety information carefully before operating the machine. This information includes important safeguards about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact your local Antari dealer for help.

Keep this device dry
Always connect to a grounded circuit to avoid the risk of electrocution.
Before connecting the machine to power, always check the voltage indicated on the machine matches your local AC voltage
Do not use the machine if the AC power voltage does not match.
Disconnect the machine from the AC power before servicing and when not in use.
This product is for indoor use only! Do not expose to rain or moisture
If the fluid is spilled, disconnect the AC power and clean it with a damp cloth.
If the fluid is spilled onto electronic parts, immediately unplug the machine and contact your local Antari dealer for advice.
No user-serviceable and modifiable parts inside
Never try to repair this product, an unauthorized technician may cause damage or malfunction to the machine.
For adult use only. Never leave the machine running unattended
Install the machine in a well-ventilated area. Provide at least 50 cm of space around the machine.
Never add flammable liquid of any kind to the machine.
Make sure there are no flammable materials close to the machine while operating.
Only use Antari fluid. Other fluids may lead to heater clogging and malfunction.
If the machine fails to work, unplug the machine and stop operation immediately.
Contact your local Antari dealer for advice.
Before transporting the machine, make sure the fluid tank is completely drained.
Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it
securely. In case of eye contact or if fluid is swallowed, immediately look for medical advice.

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, and check the content to ensure that all parts are present and have been received in good condition. If any parts appear damaged or mishandled from shipping, notify the shipper immediately and retain the packing material for inspection.
What is included:
1 x Z-1520 RGB Fogger
1 x W-2 Wireless Remote
1 x Power Cord
1 x User Manual

Product Dimensions

Product Overview

Setting Up
Step 1: Place the machine on a flat surface and in a suitably large area with at least 50 cm of open space around the machine.
Step 2: Fill the fluid tank with Antari-approved fluid.
Step 3: Connect the machine to a suitably rated power supply. To determine the power requirement for the machine refer to the label on the back of the machine.
** Always connect the machine to a protected circuit and ensure it is properly grounded to avoid the risk of electrocution.
Step 4: Turn on the machine and allow it to heat up. The heat-up takes approximately 5 minutes. Once the machine has reached operating temperature, the LCD display will show
“Ready To Fog”. Now the machine is ready for operation.
Step 5: To start making fog, locate the Volume! button on the control panel, and press the button to start making fog.
Step 6:** To turn off the machine, press the STOP button and turn Powercon to the OFF position.

Operation

Control Panel Operation
The machine can be operated with the onboard digital control interface.

Button	Function
[MENU]	Scroll through the setting menu
▲ [UP]/[TIMER]	Up/Activate Timer function
▼ [DOWN]/[VOLUME	Down/Activate Volume function
[STOP]	Deactivate Timer/Volume function

Control Menu

DMX512
Address: 1| Set DMX address from 1 to 504
---|---
Stand Alone
Set Master| Set machine as Master of Slave unit
Color Mode On| Turn LED on or off
Color Mode
Macro:01| Set LED output color from macro 1 to 10
Color Mode
Chase:01| Set LED chase from 1 to 15
Timer
Interval 15 Sec| The set interval from 15 to 360 seconds
Timer
Duration 5 Sec| Set duration from 1 to 5 seconds
Wireless Setting On| Turn the wireless control on or off
Wireless Setting
Button A: M01| Set the wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button B: M01| Set the wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button C: M01| Set the wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button D: M01| Set wireless remote button function macro color 1 to 10 or chase
LED Setting
Fog Only| 1 to 15 and off.
Setting for LED to turn on with fog only or always on.
LED Fade Out
Delay: 0 Sec| Set LED delay time from 0 to 5 seconds.
Run Last Setting On| Turn run last setting function on/off

Wireless Operation
The wireless remote control system W-2 consists of a transmitter equipped with four buttons to activate four user-configurable LED settings and fog; with an onboard receiver attached to the rear panel of Z-1520 RGB.

W-2 Wireless Transmitter
Wireless Receiver

Wireless settings are configurable through the onboard control panel, refer to the control menu section to set up each button.
In free open space, the effective distance is 50 meters, and actual usage depending on obstacle level is 10-25 meters.
Registering transmitters
Transmitters can be paired or deleted from the receiver. Each receiver can pair up to 10 transmitters. Follow the steps below to pair or delete a transmitter from a receiver.
Step 1: Power off the Z-1520 RGB Fogger.
Step 2: Press and hold the [DOWN] button.
Step 3: Turn the power on and release the [DOWN] button when the LCD display blinks.
Step 4: Follow the menu instruction to pair or delete transmitters.

If the effective distance seems to decrease, it is possible the battery level is low and requires replacement. In order to replace the battery, undo the three screws on the back of the transmitter to release the cover. Replace with the same type and specification of battery which is 27A 12V.
DMX Connector Pin Assignment
The machine provides 3-pin and 5-pin XLR connectors for DMX connection. The diagram below indicates pin assignment information.

Pin	Function
1	Ground
2	Data-
3	Data+
4	N/A
5	N/A

DMX Channel Function

Channel 1	DMX Value Range	Function
Fog	0 – 4
5 – 255	Fog Off

Fluid
Only use Antari FLC water-based liquid for the Z-1520 RGB Fogger. The machine is tested
and calibrated with this liquid to get the best output performance. Warranty will be voided if
any other type of liquid is used, improper use of liquid may lead to machine failure and
malfunction.

Service and Maintenance

Do not allow the machine to become contaminated.
Remove dust from air vents with an air compressor, vacuum, or a soft brush.
Only use a damp cloth to clean the casing.
Before storing run distilled water through the system to help avoid condensing the pump or heater.
It is recommended to run the machine on a monthly basis in order to achieve the best performance and output condition.
Excessive dust, liquid, and dirt built up will degrade performance and cause overheating.

Breaker Reset
** Disconnect the AC power before resetting the breaker. Only replace the fuse with the same type and rating.
Step 1: Disconnect the AC power.
Step 2: Flip the breaker to the ON position.
Step 3: Turn on the machine for testing.
Breaker**
100V = 16A 250V
120V = 15A 250V
240V = 9A 250V

Technical Specifications

– Input voltage| US model : AC 100-120V, 50 / 60Hz 13.5A
EU model : AC 220-240V, 50 / 60Hz 7A
---|---
– Rated power| 1600W
– Light source| 22 x 3W LED (8 Red, 7 Green, 7 Blue)
– Warm-up time| 5 minutes (approx.)
– Fluid consumption| 150 ml/min
– Fluid tank capacity| 2.41 (0.63ga1)
– Compatible fluid| Antari FLC Super Light Fog Fluid
– Ambient temp. range| 0°C – 40 °C (32 °F-104 °F)
– Output| 6 meters height
– Control| DMX512, Timer, Manual, Master/Slave, Wireless
– DMX channels| 8 channels
– Connection| Neutrik Powercon (Power) XLR 3-pin and 5-pin (DMX)
– Optional accessories| FX-4 Flightcase
– Dimension| L418 W295 H210 mm (L16.46 W11.61 148.27 inch)
– Weight| 10.4 kg (22.93 Ibs)

For current product information
visit Antarl at: wvAv.antarl.com
For Information requests please contact us
at: sales@antarl.com

http://www.antari.com.tw/index.php/mobile| http://www.antari.com/index.php/mobile