Neomounts MED-M050 Medical Mount Instruction Manual
- June 12, 2024
- Neomounts
Table of Contents
Neomounts MED-M050 Medical Mount
DIMENSIONS
PARTS
INSTALLATION INSTRUCTIONS
CART ADJUSTMENTS AND OPERATIONS
WARNING
Please put the brake on the casters when the cart is not in motion
MAINTENANCE
All cart maintenance must be carried out at least once a month by a professional technician.
Cleaning warning
Because the cart is in the environment of electrical equipment, the usage of
inflammable cleansers are strictly forbidden.
- Before cleaning the cart, please make sure the cart is unplugged from the mains and switched off.
- Please ensure the cart is entirely dry before plugging the power into the socket.
- While cleaning the cart, please use a damp cloth to wipe off the superficial cleansers until completely dry.
- The cart is not to be used in a moist environment and liquids have to be avoided from running into the cart.
- To avoid the finishing of the surface being damaged, do not use any abrasive materials for cleaning.
- Before using any cleanser on the cart, please test them on a small part to see whether it affects the surface or not.
Please note that these guidelines give no guarantee whatsoever in terms of infection control. Kindly consult your medical infection control specialist for cleaning advice.
Cleaning recommendations
- Please use non-abrasive or diluted products such as soap water and diluted alcohol to clean the plastic components.
- In case of spots of pen or maker on the cart’s surface, a soft cloth with 91% isopropyl alcohol is suggested for cleaning.
- In cased of iodine spots on the cart’s surface, a soft cloth with soap water or diluted alcohol is suggested for cleaning.
The following chemicals are strictly forbidden for cleaning the cart: Abrasive cleansers, acetone , mineral spirits, point thinner or any other harsh or toxic chemicals.
lnspections
All cart inspections must be carried out at least once a month by a
professional technician. In case of faults or damage occurring, stop operating
the cart and contact your distributor for further assistance.
Casters
To allow the cart to move as intended, please inspect the casters regularly
and keep the cart away from damaged and irregular surfaces.
Fasteners
lf fasteners/ screws become loose and need to be tightened, do not over-
tighten them. Over-tightened fasteners/ screws might not only cause damage to
the screws but also to the components
Troubleshooting
The cart is difficult to move
Ensure the two front locking casters are not locked. Check if any debris is
sticking to casters and remove it.
The cart is difficult to adjust in height
Ensure the lift brake is pressed completely and lift the work surface
slightly, to prevent the work surface to rise too quickly. lf the lift
mechanism still doesn’t work, please contact your distributor for further
assistance. Also contact your distributor for assistance if the lift mechanism
keeps going up automatically
CAUTION
- To ensure safety, please read this manual carefully before installation and follow the instructions. Store this manual in : a secure place for future reference.
- The manufacturer shall not be legally responsible for any equipment damage or personal injury caused by incorrect installation or operation other than that covered in this manual.
- The mount is designed for easy installation and removal. The manufacturer shall not be liable for damage to equipment or personal injuries arising out of human factors or acts of nature, such as earthquake or typhoon. or as
- It is recommended that the mount be installed by qualified personnel only.
- At least two persons are needed to install or remove the product to avoid hazard of falling objects.
- Please carefully inspect the area where the mount is to be installed:
- Avoid places that are subject to high temperatures, humidity or contact with water.
- Do not install the product near air conditioning vents or areas with excess dust and fumes.
- Only install on vertical walls and avoid slanted surfaces.
- Do not install in places subject to any shock or vibration.
- Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when viewing the display panel.
- Maintain sufficient space around the display to ensure adequate ventilation.
- To ensure safe installation, first check the structure of the wall, ceiling or floor and select a secure mounting location.
- The wall, ceiling or floor should be strong enough to sustain a weight of at least four times of the display and mount combined. The mounting location must be able to withstand earhquake or other strong shock.
- Do not modify any accessories or use broken parts. Contact your dealer with any questions.
- Tighten all screws (do not exert excessive force to avoid breaking the screw or damaging its thread).
- Drill holes and bolts will in be left in the wall, ceiling or floor once the display and bracket are removed. Stains may occur after extended use.
- Since the manufacturer has no way to control the wall, ceiling or floor type and installation of the mount, the warranty of the product shall only cover the body of the mount. The warranty period of the product is 5 years.
- Please consult the English language manual for any dispute on conditions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>