UTEPO UTP3SW04TP60 4 Port PoE Switch User Manual
- June 12, 2024
- UTEPO
Table of Contents
UTP3SW04TP60 4 Port PoE Switch
User Manual
UTP3SW04TP60 4 Port PoE Switch
4 Port PoE Ethernet Switch is a switch that is aimed at Ethernet high-
definition surveillance and security system of Ethernet projects. The product
fully combines the features of security surveillance, provides forwarding
capability of fast packets and abundant backplane bandwidth, ensuring clear
image and smooth transmission. protection circuit against surges and ESD can
improve the stability of the product. The product supports a model of IP CCTV,
it can achieve a VLAN, control a network storm, protecting information
security, prevent viral transmission and Ethernet attack, meet completely the
Ethernet video security surveillance system and Ethernet project needs.
Application
Feature
- Main ports: 2 x 100Mbps uplink Ethernet ports (reserve one port to connect to the Internet), 4 x 100Mbps downlink PoE Ethernet ports, each port supports MDI/MDIX.
- Special function: one key CCTV model; 1ÿ4 downlink ports can only communicate with uplink ports.
- Power input: DC48V ÿ 57V.
- Transmission distance: Ethernet port 0 ÿ 100m; the farthest transmission distance could reach 250m in CCTV model; The uplink port can reach 100m.
- Standard: Complies with IEEE802.3, IEEE802.3u, IEEE802.3 af/at standards, PoE uses End-Span, spare cable can be other use.
- Protection: Excellent anti-thunder, anti-static and anti-interference ability.
- Appearance: Delicate design and easy installation, set the anti-theft lock hole, protect against theft.
- Operation: Plug and Play, no configuration required.
Important
The transmission distance is related to the connected cable. We suggest a
standard Cat5e/6 network cable, so the transmission distance may be longer.
Switch diagram
Important
- The device must be connected with lightning protection ground; otherwise, the protection level will be will reduce; Use wire no. ° 20 above to connect the ground terminal.
- Turn the dial to the left, the equipment can enter the watchdog module after supplying power to the equipment.
Installation steps
Check the following items before installation; if it is missing, contact the dealer.
| 4 port switch power adapter | PC 1 |
|---|---|
| AC power cord | PC 1 |
| Accessory | PC 1 |
| User’s manual | PC 1 |
Then follow the steps below for installation
- Please turn off signal power and show device power before installation, or it will damage the transmission equipment.
- Use a network cable to connect the PoE IP camera and 1ÿ4 downlink ports of the product respectively.
- Use a network cable to connect the uplink port of the equipment and the NVR or PC.
- Connect the power adapter.
- Check whether the installation is correct, the equipment is in good condition, the connection is stable, then turn on the system.
- Make sure the powered on Ethernet equipment is working properly.
Specifications
| Model | Description |
|---|---|
| Energy | Power supply |
| voltage range | DC48V – 54V |
| Consumption | ÿ 5W |
| Ethernet | Speed |
Default: 10/100Mbps;
CCTV: 10 Mbps;
UPLINK: 100 m
transmission distance| Por114:
Default 0ÿ 100m:
CCTV: 0 ∼ 250 m;
UPUNK: 100m
Switch| Ethernet Standard| IEEE 802.3 / 802.3u / 802.3af / at
exchange capacity| 1.0 Gbps
Packet forwarding rate| 0.74 Mpps
packet buffer| 768K
MAC| 2k
status indicator| power light| 1pc(red)
ethernet port light| 2 pieces (yellow and green) on RJ45, yellow indicates
PoE,
Verde indica Link / Act
Watchdog Module Light| 1 pas (green), green indicates CCTV
Protection level| Group Pulse| Level 3
Standard: IEC61000-44
ESD| 1a Contact discharge level 3
1b Air discharge level 3
Standard: IEC61000-4-2
anti-thunder level| 6KV
Standard: IEC61000-4-5
Working Environment| Work temperature| – 10 ÿ-ss9
Storage temperature| – 40 ÿ – 85y
Humidity (not condescending)| 0 ∼ 95%
Mechanic| Dimension(L* In • H)| 135 Mm x 85,6 mm x 27 MM
Outside shell| galvanized sheet
Color| Negro
Weight| 315 g
Power distance 54V| Distance| 100m| 150m| 203m| 250m
Can| 26W| 24W| 23W| 21W
Troubleshooting
Follow the steps if the computer has problems.
- Make sure the equipment is installed in accordance with the manufacturer’s installation guide.
- Please confirm that the RJ45 cable order complies with EIA/TIA568A or 568B standards.
- Each PoE port can provide PoE equipment with a maximum power of less than 30W, please do not connect PoE equipment with a power greater than 30 W.
- Replace the equipment with a working 4-port PoE switch to check if the equipment is damaged.
- Contact your provider if the problem persists.
Connector production method
Instruments to use: cable crimper, network tester. The wire sequence of the RJ45 plug must comply with EIA/TIA568A o 568B.
- Remove the 2cm long insulating layer and 4-pair bare UTP cable;
- Separate the 4 pairs of UTP cables and stretch them;
- Align the 8 pieces of wires according to EIA/TIA 568A or 568B;
- Cut the wires to leave 1.5 cm of bare wire;
- Plug 8 wires into the RJ45 socket, make sure each wire is on each pin;
- Use the wire crimper to crimp it;
- Repeat the 5 steps above to make the other end;
- Please use a network tester to test the cable if it works.
| Pin | Color |
|---|---|
| 1 | White green |
| 2 | Green |
| 3 | white/orange |
| 4 | Blue |
| 5 | White blue |
| 6 | orange |
| 7 | White Brown |
| 8 | Brown |
EIA/TIA 568A
| Pin | Color |
|---|---|
| 1 | white/orange |
| 2 | orange |
| 3 | White green |
| 4 | Blue |
| 5 | White blue |
| 6 | Green |
| 7 | White Brown |
| 8 | Brown |
Important
When you choose RJ45, please make sure if one end is EIA/TIA568A, the other
end must be EIA/TIA568A as well. When you choose RJ45, make sure that if one
end is EIA/TIA568B, the other end must also be EIA/TIA568B.
Version 1.2
Documents / Resources
|
UTEPO UTP3SW04TP60 4 Port PoE
Switch
[pdf] User Manual
UTP3SW04TP60 4 Port PoE Switch, UTP3SW04TP60, 4 Port PoE Switch, PoE Switch,
Switch
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>