UTEPO UTP3-SW0401-TP60 4 Port PoE Switch User Manual
- October 30, 2023
- UTEPO
Table of Contents
UTP3-SW0401-TP60 4 Port Poe Switch
User Manual
4 Port Poe Switch (One Port Uplink)
User’s manual
Version 1.0
UTP3-SW0401-TP60 4 Port Poe Switch
4 Port Poe Ethernet Switch is a switch that is aimed at Ethernet high- definition surveillance and security system of Ethernet projects. The product fully combines the features of security surveillance, provides forwarding capability of fast packets and abundant backplane bandwidth, ensuring clear image and smooth transmission. The protection circuit against surges and ESD can improve the stability of the product. The product supports a model of IP CCTV, can achieve a VLAN, control a network storm, protecting information security, prevent viral transmission and Ethernet attack, fully satisfy Ethernet video security surveillance system and Ethernet project needs.
Application
Feature
- 4 10/100Base-TX Ethernet ports (Poe ports) and 1 10/100Base-TX uplink port; Supports standards
- IEEE802.3af/at, single port 30W max output.
- One-key CCTV mode: 1~4 downlink ports can only communicate with uplink ports, extend the transmission distance up to 250m (10Mbps)
- 6KV surge protection, 8KV ESD immunity and anti-interference.
- Easy and secure installation: wall mount, desktop, Kensington security slot; Plug and play.
Important
The transmission distance is related to the connected cable. We suggest a
standard Cat5e/6 network cable, so the Transmission distance can be up to
100m.
switch diagram
Description :
- The equipment must be grounded according to the request.
- Turn the dial to the left, the equipment can enter CCTV mode after restarting the equipment.
installation steps
Check the following items before installation; if it is missing, contact the dealer.
| 4 Port Poe Switch | 1 PC |
|---|---|
| Power adapter | 1 PC |
| AC power cord | 1 PC |
| Accessory | 1 game |
| User’s manual | 1 game |
Follow the installation steps below
- Please turn off signal power and show device power before installation, installation with power will damage the transmission equipment;
- Use a network cable to connect the Poe IP camera and 1ÿ4 downlink ports of the product respectively;
- Use a network cable to connect the equipment to the gateway and the NVR or computer;
- Turn on the equipment;
- Check whether the installation is correct, the equipment is in good condition, the connection is stable, then provide power to the system;
- Make sure the Ethernet equipment has power and is working properly.
Specifications
| model | Description |
|---|---|
| Pow apply | Open adapter |
| voltage range | DC4I3V – 54V |
| Consumption | 9 SW |
| Ethernet | Spell |
CCTV: 10 MPs: epee con: 100 Blips
transmission distance| Pori 14: OSA: 0 7 100.:
CCTV: 0 – 250 m: upu·sc: mos.
| Ethernet Standard| IEEE 802.3 802.3u 802.3a f at
exchange capacity| 1.0 Gaps
Packet forwarding rate| 0.74 Mops
packet buffer| 768K
MAC address| 2k
status indicator| Pert hoe| 1 pc(red)
ethernet port light
ethernet| 2 pieces (yellow and green) on RJ45. yellow indicates Poe.
McGee Link. Act
Watchdog Module Light| 1pc (green), green means CCTV
protection level| Group Pulse| Level 3
Standard: IEC61000-4-4
ESC/| contact discharge 6KV Air Discharge Level 8KV Standard: IEC61000-4-2
anti thunder level| 6KV
Stamford: IEC61000-4-5
Malting
Environment| Work temperature| -10 9 .. 559
storage leasable| – 40 y • 85 Y
Humidity (not condescending)| 0 -. 95°.
Mechanic| Dimension(L• In • H)| 135 mm • 85.6 mm • 27 rim
outside shell| galvanized sheet
Color| Grey
Weight| 3159
Problem solving
Follow the steps if the computer has problems.
- Make sure the equipment is installed in accordance with the manufacturer’s installation guide. Confirm that the cable order
- RJ45 meets EIA/TIA568A or 568B standards.
- Each Poe port can provide Poe equipment with a maximum power of less than 30W, please do not connect Poe equipment with a power greater than 30 W.
- Replace the equipment with a working 4-port Poe switch to check if the equipment is damaged.
- Contact your provider if the problem persists.
Connector production method
Instruments to use: cable crimper, network tester. The wire sequence of the RJ45 plug must comply with EIA /TIA568A o 568B.
- Remove the 2cm long insulating layer and 4-pair bare UTP cable;
- Separate the 4 pairs of UTP cables and stretch them;
- Align the 8 pieces of wires according to EIA/TIA 568A or 568B;
- Cut the wires to leave 1.5 cm of bare wire;
- Plug 8 wires into the RJ45 socket, make sure each wire is on each pin;
- Use the wire crimper to crimp it;
- Repeat the 5 steps above to make the other end;
- Please use a network tester to test the cable if it works.
Important
When you choose RJ45, please make sure if one end is EIA/TIA568A, the other
end must be EIA/TIA568A as well. When you choose RJ45, make sure that if one
end is EIA/TIA568B, the other end must also be EIA/TIA568B.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>