ETHAN ALLEN 093068 Charlotte Beaded Chandelier Instruction Manual
- June 12, 2024
- ETHAN ALLEN
Table of Contents
Charlotte Beaded Chandelier
ASSEMBLY INSTRUCTIONS
093068 NAT
IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS COMPLETELY BEFORE
STARTING.
We strongly recommend that all direct-wired lighting products be installed by
a licensed electrician. Two people may be required for installation. DO NOT
EXCEED the rated bulb wattage. Keep flammable materials away from bulbs. This
light fixture is shipped with all internal wiring intact. Do not open the
product or alter the wiring in any manner.
Installation requires an electrical junction box in the ceiling sufficient to
support the weight of the light fixture.
This fixture weighs: 43lbs. (19.5kg).
WARNING: Be certain that the power to the electrical junction box is
turned off at the circuit breaker before installation. Turning the power off
at a light switch is not sufficient to prevent electrical shock.
CAUTION: Prior to installation, locate All INCLUDED PARTS before
disposing of packaging materials.
TOOLS REQUIRED FOR INSTALLATION
Screwdrivers| Pliers
Electrical Tape| Wire Connectors
Wire Cutters| Adjustable Wrench
Note: Lightbulb(s) are not included. See light fixture for bulb specification. Additional wiring supplies may be required
Parts Not Included:
Part| Qty.| Description
A| 1| Ceiling Outlet Junction Box
B| 1| Hot Junction Box Wire
C| 1| Neutral Junction Box Wire
D| 1| Ground Junction Box Wire
Parts Included (Refer to figure):
Part| Qty| Description
E| 3| Wire Connectors
F| 1| Mounting Bracket
G| 1| Ground Screw
H| 2| Mounting Screws
I| 1| Nipple
J| 2| Hex Nut
K| 1| Lock Washer
L| 1| Canopy
M| 1| Collar Loop
N| 1| Thread Ring
O| 1| Chain
P| 1| Fixture Loop
Q| 6| Candle Sleeves
093068 NAT Charlotte Beaded Chandelier Brass Assembly Instructions, continued
ASSEMBLY PROCEDURES:
-
SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
-
Remove all the parts from the carton. Do not throw away any parts.
-
Attach the Fixture Loop (P) to the threaded tube at the top of the Fixture Body. Screw it in until tightened.
-
Gently pull existing ground (D), Hot (B), and Neutral (C) Junction Box Wires down from the Ceiling Junction Box (A) and allow these to hang.
-
Carefully inspect the wires on the chandelier fixture. The Neutral Fixture Wire is ribbed. The Hot Fixture Wire is smooth, and the Ground Wire is copper.
-
Attach the Ground Wire from the fixture to the Ground Junction Box Wire (D); it usually has green insulation around it or is bare wire.
Fasten these together with a Wire Connector (E) and wrap the connection with electrical tape. Make sure no wire strands are exposed. If your Ceiling Outlet Junction Box (A) does not have a Ground Junction Box Wire (D), insert the Ground Screw (G) into the Mounting Bracket (F) where it is marked “Ground” and wrap the bare ground wire from the chandelier around the Ground Screw (G).
Tighten the screw to clamp the Ground Wire between the Ground Screw (G) head and the Mounting Bracket (F). IT IS IMPERATIVE THAT THE CEILING JUNCTION BOX (A) IN YOUR HOME BE PROPERLY GROUNDED. -
Connect the Neutral Fixture Wire to the Neutral Junction Box Wire (C); it usually has white insulation around it.
Fasten these together with a plastic Wire Connector (E) and wrap the connection with electrical tape. Make sure that no wire strands are exposed. -
Connect the Hot Fixture Wire to Hot Junction Box Wire (B); it usually has black insulation around it. Fasten these together with a plastic Wire Connector (E) and wrap the connection with electrical tape. Make sure that no wire strands are exposed. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
-
Gently tuck the wire connections neatly into the Ceiling Outlet Junction Box (A).
-
Attach the Mounting Bracket (F) to the Ceiling Outlet Junction Box (A) using the Mounting Screws (H). Tighten screws with a screwdriver until secure.
-
Attach one Hex Nut (J) to the top and the other Hex Nut (J) to the bottom of the Nipple (I). Put the Lock Washer (K) in before attaching the Collar Loop (M) to the bottom end of the Nipple (I).
-
Secure the top of the Nipple (I) to the Mounting Bracket (F) with the Hex Nut (J), exposing approximately 2” of the thread. Then secure the Collar Loop (M) to the bottom end of the Nipple (I) with the Hex Nuts (J) and Lock Washer (K).
-
Slide the Canopy (L) and the Threaded Ring (N) up the Chain (O).
-
Place the Canopy (L) over the Ceiling Outlet Junction Box (A) and secure it in place by screwing the Threaded Ring (N) onto the Collar Loop (M).
-
Place the Candle Sleeve (Q) over the sockets of the fixture body.
-
Insert Six (6) 60-Watt maximum Type B Candelabra incandescent light bulbs (not included) or six (6) 13-watt maximum compact fluorescent light bulb (not included) or six (6) 9-watt maximum LED light bulb (not included) into the sockets. Do not exceed the specified wattage.
CARE INSTRUCTIONS
- Wipe with a soft, dry cloth.
- AVOID cleaners, harsh chemicals, scouring pads, etc. as these may cause damage to the pendant finish.
After troubleshooting, if the light fixture still does not work, contact your
local Ethan Allen Design Center.
SAVE THESE INSTRUCTIONS
©2023 Ethan Allen Global, Inc
Documents / Resources
|
ETHAN ALLEN 093068 Charlotte Beaded
Chandelier
[pdf] Instruction Manual
093068 Charlotte Beaded Chandelier, 093068, Charlotte Beaded Chandelier,
Beaded Chandelier, Chandelier
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>