EMOS H4032 IP Door Camera Unit Instruction Manual
- June 17, 2024
- EMOS
Table of Contents
EMOS H4032 IP Door Camera Unit
Specifications:
-
Lens: 3.2 mm, F2.0
-
Storage: SD card (Max. 128 GB), Cloud
storage -
Enclosure rating: IP65
-
APP: EMOS GoSmart for Android and iOS
-
Connection: 2.4 GHz WIFI
(IEEE802.11b/g/n) -
Maximum number of users: 4
-
Distance: approx. 80 m (open space)
Product Usage Instructions
Installing the Camera onto a Wall (Powered by Batteries):
- Install the mount on a wall with screws.
- Install the camera in the mount and affix it with a screw.
Installing the Camera onto a Wall (Powered from the Grid):
- Prepare the accessories required for powering by AC power.
- Place and install the mount on the wall and connect the mount to an AC power source.
- Install the camera in the mount and affix it with a screw.
Installing the EMOS GoSmart App:
- The app is available for Android and iOS on Google Play and App Store.
- Download the application by scanning the corresponding QR code.
Router Setting
The camera only supports 2.4 GHz Wifi (not 5 GHz).
EMOS GoSmart Mobile App:
- Open EMOS GoSmart and confirm the privacy policy by tapping agree.
- Choose sign up.
- Enter a valid e-mail address and choose a password. Confirm the privacy policy by tapping agree. Choose log in.
- Choose add device.
- Choose the corresponding product category.
- Choose the correct type of product.
- Connect the device to power.
- Make sure the LED on the device is flashing. Confirm by tapping next.
- Enter the name of the Wifi network and password. Confirm by tapping next.
- A QR code will appear on the screen of your device. Place the QR code in front of the lens of the camera unit. Confirm that you have heard an audio signal for successful pairing.
- The device will be detected automatically.
- The device has been found. Confirm by tapping done.
FAQ:
- Q: How do I dispose of the product properly?
A: Do not dispose with domestic waste. Use special collection points for sorted waste. Contact local authorities for information about collection points. If the electronic devices would be disposed on landfill, dangerous substances may reach groundwater and subsequently food chain, where it could affect human health.
IP Door Camera Unit
Package contents
- Chime Wireless doorbell
- Mount Screws
- Screwdriver RESET pin
- Power adapter USB cable
- 3× AA LR6 1.5 V Manual
Technical specifications
Wifi doorbell
- Power supply: DC 5 V/1 A, AC 12~24 V
- Dimensions: 140 × 55 × 40 mm
- Net weight: 200 g
- Resolution: 1 920 × 1 080
- Sensor: 1/2.9‘‘ 2 Megapixel CMOS
- Battery capacity: 6 700 mAh
- PIR detection range: 5 m
- PIR angle: 100°
- Lens: 3.2 mm, F2.0
- Storage: SD card (Max. 128 GB), Cloud storage
- Enclosure rating: IP65
- APP: EMOS GoSmart for Android and iOS
- Connection: 2.4 GHz WIFI
- (IEEE802.11b/g/n)
- Maximum number of users: 4
Wireless doorbell
- Power: 3× AA (LR6) 1.5 V
- Frequency: 433.92 MHz ±250 kHz
- Distance: approx. 80 m (open space)
Description of the device: fig. 1a
- A – Light sensor
- B – Lens
- C – Micro USB port
- D – PIR sensor
- E – Microphone
- F – Status LED
- G – Doorbell button
- H – SD card slot
- I – On/off button
- J – RESET button
- K – External power supply
- L – Speaker
Description of the device: fig. 1b
A – LED status light- B – Speaker
- C – Volume
- D – Melody
- E – Pairing button
- F – Micro USB
Installing the camera onto a wall (powered by batteries): fig. 2a
- Install the mount on a wall with screws.
- Install the camera in the mount and affix it with a screw.
Installing the camera onto a wall (powered from the grid): fig. 2b
- Prepare the accessories required for powering by AC power.
- Place and install the mount on the wall and connect the mount to an AC power source.
- Install the camera in the mount and affix it with a screw.
Pairing a wireless doorbell with a Wifi doorbell:
- Press the button” ”for 2seconds, the status LED flashes red slowly and the doorbell is in pairing mode.
- Then press the ring button on the Wi-fi doorbell, once the status LED goes off and the melody automatically plays – the pairing was successful.
Cancel pairing of the wireless doorbell with the Wi-fi doorbell:
- Press the button” ”for 5seconds, the device is in factory setting.
Installing the EMOS GoSmart app: fig. 3
The app is available for Android and iOS on Google play and App Store.
Download the application by scanning the corresponding QR code.
Router setting: fig. 4
EMOS GoSmart
mobile app
Fig. 5a
Open EMOS GoSmart and confirm the privacy policy by tapping agree.
Fig. 5b
Choose sign up.
Fig. 5c
Enter a valid e-mail address and choose a password.
Confirm the privacy policy by tapping agree.
Choose log in.
Fig. 6a
Choose add device.
Fig. 6b
Choose the corresponding product category.
Fig. 6c
Choose the correct type of product.
Fig. 6d
Connect the device to power.
Fig. 6e
Make sure the LED on the device is flashing.
Confirm by tapping next.
Fig. 6f
Enter the name of the Wifi network and password.
Confirm by tapping next.
Fig. 6g
A QR code will appear on the screen of your device.
Place the QR code in front of the lens of the camera unit.
Confirm that you have heard an audio signal for successful pairing.
Fig. 6h
The device will be detected automatically.
Fig. 6i
- The device has been found.
- Confirm by tapping done.
- The camera only supports 2.4 GHz Wifi (not 5 GHz).
- Connectivity: Wi-Fi 2.4 GHz IEEE 802.11b/g/n
- Frequency band: 2.400–2.4835 GHz
Do not dispose with domestic waste. Use special collection points for sorted
waste. Contact local authorities for information about collection points. If
the electronic devices would be disposed on landfill, dangerous substances may
reach groundwater and subsequently food chain, where it could affect human
health.
Hereby, EMOS spol. s r.o. declares that the radio equipment type H4032 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
http://www.emos.eu/download.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>