TINECO FW14 Floor One S6 Series Smart Cordless Floor Washer User Manual
- June 17, 2024
- Tineco
Table of Contents
FLOOR ONE S6 SERIES
Smart Cordless Floor Washer
Instruction Manual
*Actual product may differ from illustration.
TINECO IS HERE TO HELP
We’ll get back to you within 24 hours.
Important Safety Instructions
SAVE THESE INSTRUCTIONS
Household use only.
When using an electrical appliance, basic precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
WARNING – To reduce the risk of fire, electric shock, or injury:
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision. -
The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
-
Use only indoors, on non-carpeted floor surfaces such as vinyl, tile, sealed wood, etc. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.
-
Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.
-
Use only as described in this manual. Use only manufacturer’s recommended attachments.
-
Do not use with a damaged cord or plug. If appliance has been dropped, damaged, left outdoors, dropped into water, or is not working as it should, return it to a service center.
-
Do not handle charger, including charger plug, and charger terminals with wet hands.
-
Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
-
Keep hair, loose clothing, fingers, and all parts of your body away from openings and moving parts.
-
Use extra care when cleaning on stairs.
-
Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
-
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
-
Do not use without filter.
-
Prevent unintentional activation. Ensure the switch is in the off-position before picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.
-
Always switch off the appliance before making any adjustments, changing accessories, or storing the appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
-
Recharge only with the charger specified by Tineco. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
-
Use appliances only with specifically designated Tineco battery packs. Use of any other battery packs may create a risk of injury and fire.
-
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid comes into eye contact, seek medical help. Liquid ejected from the battery may cause irritation or burns.
-
Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
-
Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 266°F (130°C) may cause an explosion.
-
Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
-
Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
-
This appliance contains battery cells that are non-replaceable. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.
-
Always turn off this appliance before connecting or disconnecting the motorized nozzle.
-
Do not charge or store the appliance outdoors or inside the car. Only charge, store or use the battery in a dry indoor area where the temperature is higher than 39.2°F (4°C) but lower than 104°F (40°C). The charger is for indoor use only.
-
Do not use to pick up ultrafine particles, such as lime, cement, sawdust, gypsum powder, or ashes.
-
Do not use to pick up sharp objects, such as metallic nails, pieces of glass, metal paper clips, or pins.
-
Do not use to pick up hazardous material and chemicals, such as solvent, drain cleaner, strong acids, or strong alkali.
-
Stop using immediately if the appliance is overheating, making unusual noises, producing unusual odors, performing low suction, or leaks electricity.
-
Turn cleaner OFF and disconnect from electrical outlet for long-term storage.
-
Always clean the Dirty Water Tank after each use to avoid potential blockage, which may lead to low suction power, motor overheating, or reduce the service life of the appliance.
-
Store appropriately indoors in a dry place after use.
-
Do not place or submerge appliance in standing water or try to clean flooded areas.
-
All data and technical instructions of this manual are based on results from lab tests of Tineco or designated third parties. The company reserves all rights for final explanations.
-
The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.
-
A hazard may occur if the appliance runs over the supply cord.
-
Do not use the appliance when the water depth is more than 5mm above the surface.
-
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
-
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Range of Usage
- The cordless hard floor cleaner is to be used on indoor hard floors, such as vinyl, tile, sealed wood, etc. Use on a rough surface may not get the best performance.
- Keep your appliance away from heat sources, such as fireplace or heater, to avoid casing deformation.
- Do not use to pick up flammable or combustible liquids, ultrafine particles, sharp objects, hazardous material, chemicals or anything that is burning or smoking, as described above.
About Cleaning Solution
- A large amount of cleaning solution entering into the motor may cause damage to the appliance.
- Add solution as instructed in the Operation section. We recommend using the provided cleaning solution. Do not use the product with acidic, alkaline solution, or any substances harmful to the environment.
- Keep out of the reach of children. Avoid contact with eyes and skin, otherwise, rinse thoroughly with water. If irritation persist, seek medical advice. If product is swallowed seek medical advice.
- Dirty water and solution disposal should comply with local environmental regulations.
About the Appliance
- Do not modify or attempt to repair the appliance except as indicated in the instructions for operating and cleaning.
- Charge the appliance with the Tineco adaptor. Input Voltage: AC 100-240V. Both high and low voltages can damage the adaptor, appliance, or even cause danger to the user.
- Use extra care when cleaning on stairs.
- Ensure that the Power Switch is in the OFF-position before picking up or carrying the appliance. Do not lay flat or lean the appliance so as to prevent dirty water from entering into the motor.
- To avoid being tripped accidentally, please put away the appliance on the charging dock.
- Always install the Dirty Water Tank and Clean Water Tank properly before use.
- Do not allow the appliance or charger to get wet to avoid risk of fire or injury caused by a short circuit.
FCC Supplier’s Declaration of Conformity
TINECO / FLOOR ONE S6 SERIES
This appliance complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This appliance may not cause harmful interference, and (2) this appliance
must accept any interference received, including interference that may cause
undesired operation.
TINECO INTELLIGENT, INC.
1700 WESTLAKE AVENUE N., SUITE 200, SEATTLE, WA, 98109, USA
WWW.TINECO.COM
1-855-292-8864
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and find it to comply with the
limits for a Class B digital appliance, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
Note
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment, such modifications could void
the user’s authority to operate this equipment.
IC Note
This appliance contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
- this appliance may not cause interference.
- this appliance must accept any interference, including interference that may cause
undesired operation of the appliance.
– This Class B digital apparatus complies with Canadian ICES-003.
– This equipment complies with ISED RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and any part of
your body.
Specifications
Product | FLOOR ONE S6 SERIES |
---|---|
AC Input | 100-240V- |
Voltage | 21.6V— 4000mAh Li-Ion |
Rated Power | 220W |
Running Time | AUTO: -35 mins MAX: -28 mins |
Charging Time | 4-5 hrs |
Water Flow Rate | 30-100m1/min |
CWT Capacity | -0.8L |
DWT Capacity | -0.7L |
Waterproof | IPX4 |
Drying charging dock
Input (drying)| 120V- 60Hz 3.8A
Input (charging)| 120V- 60Hz 0.5A
Output| 26V— 1A
Disposal
-
The battery contains materials that are harmful to the environment and must be removed from the appliance before it is discarded.
-
When removing the battery, the appliance must be powered off.
-
Batteries, chargers, accessories and packaging should be sorted for environmental friendly recycling.
Do not put them into fire, water or soil. Do not dispose of batteries and chargers into household waste! **** -
If battery leakage contacts skin or clothing, immediately flush with water to avoid irritation and seek medical help.
Overview
A. Self-cleaning Button
B. Mode Switch
C. Power On/Off
D. Digital Display
E. Dirty Water Tank Release
F. Dirty Water Tank Handle
G. Dirty Water Tank (DWT)
H. WiFi/Mute/Language Switch Button
I. Tube| J. Clean Water Tank (CWT)
K. Brush Roller Cover
L. Brush Roller
M. Deodorizing & Cleaning Solution
N. Cleaning Tool
O. Dry Filter
P. Transparent Tray
Q. Drying & Charging Dock
---|---
Digital Display
A. WiFi Indicator
B. DWT Full or Blocked
C. AUTO Mode
D. Drying Brush Roller Indicator
E. CWT Empty| F. Brush Roller Tangled Indicator
G. SUCTION Mode
H. Tineco Logo
I. Self-cleaning Icon
J. Battery Level Indicator
---|---
Accessories
Note:
Accessories may vary among markets. If you require more accessories, please go
to www.tineco.com or
store.tineco.com.
Deodorizing & Cleaning Solution
Removes dirt, grime, grease and tough stains from most types of hard surfaces,
like tile, marble, sealed hardwood floors, and more.
Always use Tineco solution in your appliance.
Add one bottle cap of solution to each full tank of clean water.
Brush Roller
Soft roller head with bristles can be used to vacuum and wash at the same time. It can be easily cleaned with the self-cleaning function.
Dry Filter
Dry filter and filter net can block large particles and debris, ensure the appliance’s durability.
- Please install the dry filter before use, or it may lead to weak suction.
Cleaning Tool
A full brush to clean the DWT, brush chamber and opening.
The tool also has a bristled end to remove dirt and mud on the roller and DWT.
Assembly
How to Assemble/Disassemble
Note:
For water tank and brush assembly, please refer to “Operation” and
“Maintenance”.
To assemble the handle, insert it into the appliance until you hear a click.
In the event that the handle needs to be disassembled, press the spring to release the handle with a tool (like a screwdriver) and lift the released handle from the appliance.
Tips:
WiFi/Mute/Language Switch Button
- Press to turn on/off the voice prompt.
- Press twice to switch languages. (More voice languages will be added, please refer to the actual product for now.)
- Hold for 3 seconds to connect to network.
Operation
Preparing for Use
Before first use, please charge the appliance for 4-5 hours (refer to
“Charging Instructions” for details).
- Based on results from Tineco lab tests. Lab temperature 39.2°F (4°C) ~ 104°F (40°C).
Press the button and the appliance will start in AUTO mode by default. Press it again to turn off the appliance. Switch between AUTO, MAX and SUCTION modes by pressing the button.
The appliance will stop working when put upright and start running again when reclined.
- Do not recline more than 142° to avoid water leakage.
Tips (SUCTION mode not available) :
-
Solution mode/ Water Only mode:
Appliance starts with Solution mode by default. Power on while the appliance is upright, hold for 3s to switch between the two modes. -
Switch to Water Only mode:
LED Loop: Red → Blue (use water only) -
Switch to Solution mode:
LED Loop: Blue → Red (use cleaning solution)
Place the appliance on the charging dock vertically after use for recharge and storage.
Note:
- It is crucial to choose the right mode based on the CWT contents to achieve the highest level of dirt detection efficiency.
- Do not vacuum foamed liquid.
- To vacuum water left on the surface, the appliance will keep running for 3 seconds after power off.
- Suction mode is only available in selected models, please refer to the actual product.
Filling Clean Water Tank
Press the Clean Water Tank release button to remove it from the appliance.
Open the tank cap, and fill with tap water to the Max line. When deep cleaning
is necessary, add one bottle cap of solution to the CWT and tightly close the
cap.
Note:
Only use water under 140°F/60°C.
DO NOT USE HOT WATER.
Place the tank back into the appliance. You should hear a “Click” if done correctly.
Charging Instructions
- To charge the appliance, plug in the drying & charging dock and place the appliance on it.
- To avoid tripping hazards, please place the appliance on the charging dock near a wall during charging.
Warning:
- Only charge the appliance with the adaptor supplied by Tineco.
- During long periods of not being used, the appliance must be charged once every 3 months for optimal performance. It may take 4-5 hours for a full charge.
- Store indoors in a dry place. Do not expose the appliance to sunlight or freezing temperatures.
Recommended temperature range: 39.2°F (4°C) ~ 104°F (40°C).
Cleaning Mode Selection
AUTO Mode
- In AUTO mode, the iLoop sensor automatically detects how dirty the floor is and applies the appropriate amount of detergent and suction power.
- A red dirt monitoring loop indicates more dirt is detected, and a blue loop indicates less dirt is detected. This mode automatically provides the best cleaning solution.
MAX Mode
- In AUTO mode, press the button to enter MAX mode Voice will be prompted. The AUTO indicator on the display will turn off.
- In MAX mode, the appliance will apply max suction power and will spray water/solution for deeper cleaning.
SUCTION Mode (only available in selected models)
- In MAX mode, press the button to enter SUCTION mode.
- In SUCTION mode, the appliance will only absorb water and do not spray. We recommend using this mode on the wet surface.
Note:
Keep sharp objects away from the digital display screen to avoid scratches and
scrapes.
Runtime
- When in AUTO mode, the runtime is approximately 35 minutes. When MAX power is used, the runtime is approximately 28 minutes.
- Estimated runtime data was obtained by Tineco Laboratory.
Charging Time
- A full charge takes approximately 4-5 hours.
- Estimated data was obtained by Tineco Laboratory using ambient temperatures ranging from 39.2°F (4°C) to 104°F (40°C).
Indicator
When in Use
| Battery level ≥ 10%: battery indicator will be illuminated.
---|---
| Battery level < 10%: battery indicator will be blinking.
| Off: no power detected or possible battery malfunction.
| Solid red light: dirt sensor malfunction or blocked.
| Indicator blinking: CWT is empty.
| Indicator blinking: DWT is full or channel has a blockage.
| Indicator blinking: brush roller has a blockage.
| Illuminated: WiFi has successfully connected.
| Blinking: WiFi is connecting.
| Off: WiFi is not connected, please connect to the network.
| Indicator blinking: appliance is in need of self-cleaning.
| Indicator blinking: Appliance is in charging, please wait for it to dry.
During Charging
Tineco indicator: breathing.
Fully Charged
In 5 minutes: Tineco indicator illuminated.
After 5 minutes: all indicator lights turn off.
App
All the functions can be performed using the Tineco app. Download the Tineco
app from App Store, Google Play and Tineco Official Site.
Note:
The default setting for voice prompt is English, you can set other languages
via App.
Voice Prompt (Contents may vary, please in kind prevail.)
Status | Reminder |
---|---|
Voice prompts on | Voice prompts on |
Voice prompts disabled | Voice prompts disabled |
Auto mode by default | Auto mode |
Switch to Max mode | Max mode |
Cleaning with water only | Cleaning with water only |
Cleaning with cleaning solution by default | Cleaning with cleaning solution |
Battery level: 10~20% | Low battery |
Battery level: 0~10% | Low battery, please charge |
Clean Water Tank is empty | Clean Water Tank empty, please refill water and |
cleaning solution
Need self cleaning| Please begin self-cleaning cycle
Appliance not on the charging dock| Please place appliance on charging dock
Dirty Water Tank is full| Dirty Water Tank full, please empty
Brush roller is tangled| Please clean the brush roller.
Power is off| Power off
Start charging| Charging has commenced
Begin self-cleaning cycle.| Auto-detecting whether to run self-cleaning cycle,
please begin self-cleaning cycle
Battery insufficient for self-cleaning| Low battery, start charging
Sufficient battery to start self cleaning| Start self cleaning
Cleaning brush roller| Cleaning brush roller
Cleaning debris channel| Cleaning debris channel
Auto detecting| Auto detecting
Deep cleaning| Deep cleaning
Self-cleaning stopped| Self-cleaning cycle stopped, please clean Dirty Water
Tank
Self-cleaning complete| Self-cleaning cycle complete, please clean Dirty Water
Tank
Maintenance
Note:
- For optimal performance and to prevent odors, always clean and dry DWT, filters, brush roller, brush roller cover completely after each use.
- Please make sure each part is installed correctly or the appliance may not work properly.
- After maintenance, place the appliance on the charging dock vertically. Do not expose the appliance to direct sunlight, and store it indoors in a dry place.
Main Body
To reduce the risk of injury, switch off before performing maintenance.
Use a cloth to clean the surface with a neutral detergent. The cloth should be dry to prevent water from entering the appliance.
Clean the dirt sensor with a damp cloth or the cleaning tool.
Dirty Water Tank
- When dirty water reaches the Max line, the appliance will stop working, show a reminder on the display and play a voice prompt.
- Pull up the tank lid to empty the DWT. Use the cleaning tool to remove remaining debris. Rinse the inside of the DWT and place back into the appliance.
Dry Filter & Waste Separator
Grasp recessed area on each side of the dry filter and pull upward. Rinse
under running water and must be completely dry before recombining with the lid
of the DWT.
A spare dry filter is provided with your appliance for convenient replacement.
The waste separator can be removed and rinsed under the running water.
The function of the waste separator is to separate solid waste.
*The appliance can function normally without the waste separator, so users can decide whether to keep it or not.
Brush Roller Self-cleaning
- Place the appliance on the charging dock after use, the sensor will auto-detect the level of dirt.
- When you hear the voice prompt “please begin selfcleaning cycle”, press the self-cleaning button and begin the process.
- Once complete, you will hear the voice prompt “selfcleaning completed, please clean the Dirty Water Tank.” At this point, the appliance will begin charging.
Note:
- Ensure the charging base is plugged in and the battery level>20%.
- Before self-cleaning cycle, please clean the DWT and ensure the water level in the CWT>40%.
Brush Roller Cover
Squeeze latches on the cover and pull upward to remove.
Rinse with water.
While replacing, always latch the brush cover into place to avoid leakage.
Brush Roller
Remove the brush roller by grabbing the brush roller tab and pulling out.
Use the cleaning tool to remove the hair and debris wrapped around the roller and then rinse the roller with water. Replace the brush roller back into the accessory holder, and allow it to dry completely before reinstalling.
Remove hair and debris from the brush roller chamber and the opening with the cleaning tool. Replace the brush roller by inserting its end into the left side of the holder, then attach the roller tab to the magnetic buckle on the right side to lock into place.
Note:
- A spare brush roller is provided with your appliance for convenient replacement.
- To maintain optimal performance, replace the brush roller every 8 months.
Brush Roller Replacement
Pull up the roller handle to remove it. Once removed, install the handle into
the new brush roller.
When uninstalling, do not directly pull on the pull ring of the brush roller.
Transparent Tray
Move the lock latch to the right, then lift the transparent tray upwards to remove it.
Clean with water or a towel, and thoroughly dry before reinstalling.
Note:
- Do not directly rinse the drying & charging dock with water. Remove the transparent tray separately for cleaning.
SCAN THE QR CODE BELOW TO GET PRODUCT CARE VIDEOS.
Troubleshooting
Problem | Possible cause | Solution |
---|---|---|
The appliance does not turn on | Auto protection for overheating | Restart after |
cooling down
Weak suction| The dry filter is not installed, or the dry filter is dirty|
Install the dry filter or clean and allow it to dry completely
Brush roller tangled indicator blinking
Voice prompt: Please clean the brush roller| The brush roller is blocked|
Remove blockages
WiFi indicator is off| WiFi is not connected| Follow the in-app guide to
connect to WiFi
CWT empty indicator blinking
Voice prompt:
Clean Water Tank empty, please refill water and cleaning solution| CWT is
empty| Refill CWT
DWT kill indicator blinking
Voice prompt: Please clean Dirty Water Tank| The dirty water in DWT has
reached the MAX line| Empty the dirty water and then reinstall the DWT
All lights off in operation| Battery overheat or malfunction| Cool the
appliance down and restart
Battery level indicator blinking
Voice prompt: Low battery, please charge| Low battery| Charge the appliance,
or restart
Self-cleaning icon blinking| Brush roller is dirty| Start self-cleaning
Note: If the above troubleshooting guide fails to provide a solution, please visit our website www.tineco.com for further support.
Warranty
3-YEAR LIMITED WARRANTY
- Only applies to purchases made from authorized retailers of Tineco.
- Is subject to the adherence of the requirements outlined in this instruction manual, and is subject to further conditions outlined below.
- This warranty is governed by and construed under the laws of the country in which the purchase took place. We provide 3-year warranty or a warranty period as stipulated by applicable local law, whichever is longer.
WHAT IS COVERED?
-
Your Tineco appliance has a 3-year warranty against original defects in material and workmanship, when used for private household purposes in accordance with the Tineco Instruction Manual.
Motorized accessories and battery bought separately come with a 1-year warranty. -
This warranty provides, at no extra cost to you, all labor and parts necessary to ensure your appliance is in proper operating condition during the warranty period.
-
This warranty will only be valid if the appliance is used in the country in which it was sold.
WHAT IS NOT COVERED?
Tineco shall not be liable for costs, damages or repairs incurred as a result
of:
- Appliances purchased from an unauthorized dealer.
- Careless operation or handling, misuse, abuse and/or lack of maintenance or use not in accordance with the Tineco Instruction Manual.
- Use of the appliance other than for normal domestic purposes, e.g. for commercial or rental purposes.
- Use of parts not in accordance with the Tineco Instruction Manual.
- Use of parts and accessories other than those produced or recommended by Tineco.
- External factors unrelated to product quality and use, such as weather, modifications, accidents, electrical outages, power surges or acts of God.
- Repairs or alterations carried out by unauthorized parties or agents.
- Failing to clear blockage and other hazardous material from the appliance.
- Normal wear and tear, including normal wearing parts, such as clear bin, belt, filter, HEPA, brush bar, and power cord (or where external damage or abuse is diagnosed), carpet or floor damage due to use not in accordance with manufacturer’s instructions or failure to turn the brush bar off when necessary.
- Reduction in battery discharge time due to battery age or use.
WARRANTY LIMITATIONS
- Any implied warranties relating to your appliance including but not limited to warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty.
- Warranty coverage applies to the original owner and to the original battery only and is not transferable.
- This limited warranty gives you specific legal rights. You may also have other rights which vary by region.
- Manufacturer’s warranties may not apply in all cases, depending on factors such as use of the product, where the product was purchased, or who you purchased the product from.
Please review the warranty carefully, and contact the manufacturer if you have any questions.
WARRANTY SERVICE
Register: We highly recommend that upon purchase, you register your appliance
by logging into our official website (www.tineco.com)
or scanning the QR code (see right) to enjoy more exclusive benefits. To
register, please enter the whole serial number (remove the Clean Water Tank
and find it on the back of the appliance).
Failure to register your product won’t diminish your warranty rights.
How to Claim: Please retain your proof of purchase. To make a claim under our
Limited Warranty, you need to provide your serial number and the original
purchase receipt with the purchase date and order number on it.
All work will be carried out by Tineco or its authorized agency.
Any replaced defective parts will become the property of Tineco.
Service under this warranty will not extend the period of this warranty.
Contact our Customer Service
Hotline: 1-855-292-8864
or Visit Tineco website
www.tineco.com
for expert customer service.
Documents / Resources
|
TINECO FW14 Floor One S6 Series Smart Cordless Floor
Washer
[pdf] User Manual
FW14 Floor One S6 Series Smart Cordless Floor Washer, FW14, Floor One S6
Series Smart Cordless Floor Washer, S6 Series Smart Cordless Floor Washer,
Smart Cordless Floor Washer, Cordless Floor Washer, Floor Washer
---|---
|
Tineco FW14 Floor One S6 Series Smart Cordless Floor
Washer
[pdf] Instruction Manual
FW14 Floor One S6 Series Smart Cordless Floor Washer, FW14, Floor One S6
Series Smart Cordless Floor Washer, S6 Series Smart Cordless Floor Washer,
Smart Cordless Floor Washer, Cordless Floor Washer, Floor Washer, Washer
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>