SEALEY AK292.V3 Electric Glue Gun Instructions
- June 16, 2024
- SEALEY
Table of Contents
SEALEY AK292.V3 Electric Glue Gun Instructions
ASEMBLE INSTRUCTION
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction Manual
Wear protective gloves
Warning! Hot Surface
SAFETY
ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe
before using. Inspect power supply leads, plugs and all electrical connections
for wear and damage. Sealey recommend that an RCD (Residual Current Device) is
used with all electrical products. You may obtain an RCD by contacting your
local Sealey dealer. if the glue gun is used in the course of business duties,
it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information
is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before
connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check
all connections to ensure that they are secure.
IMPORTANT: Ensure that the voltage rating on the appliance suits the
power supply to be used and that the plug is fitted with the correct fuse –
see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable. Remove the plug from
the socket by maintaining a firm grip on the plug.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any
faulty item is repaired or replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and
remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact
a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are
marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all
wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that
the restraint is tight.
DO NOT connect either wire to the earth terminal. Sealey recommend that
repairs are carried out by a qualified electrician.
GENERAL SAFETY
Familiarize yourself with this products application and limitations, as well
as the specific potential hazards peculiar to the glue gun.
WARNING! Disconnect the glue gun from the mains power before changing
accessories, servicing or performing any maintenance.
Maintain the glue gun in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised
parts may be dangerous and will invalidate the warranty.
WARNING! Always wear approved eye or face protection when operating the
glue gun.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Remove ill fitting clothing. Remove ties, watches, rings, and other loose
jewellery, and contain and/ or tie back long hair.
Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes,
Secure non stable workpiece with a clamp, vice or other adequate holding
device.
DO NOT use the glue gun for a task it was not designed to perform.
DO NOT operate the glue gun if any parts are damaged or missing as this
may cause failure and/or possible personal injury.
DO NOT hold the workpiece by hand. Use clamps or a vice (not included) to
secure the workpiece. Available from your Sealey dealer.
DO NOT get the glue gun wet or use in damp or wet locations or areas
where there is condensation.
DO NOT place nozzle close to your face (especially eyes, ears, etc) or
other persons or animals.
DO NOT allow children or untrained persons to operate the glue gun.
DO NOT operate the glue gun when you are tired or under the influence of
alcohol, drugs or intoxicating medication.
DO NOT get glue on your skin.
DO NOT inhale any vapour given off by the glue
DO NOT carry the glue gun with your finger on the power switch, or carry
by the power cable.
DO NOT use the glue gun where there are flammable liquids, solids or
gases such as paint solvents, etc.
DO NOT leave the glue gun operating unattended.
When not in use switch the glue gun off, remove plug from the power supply,
store the tool in a safe, dry child proof area.
NOTE: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play
with the appliance.
introduction
Composite housing with comfortable handle and trigger feed control. Fitted with 1mtr cable with BS approved 3-pin 230V rewireable fused plug. Suitable for hardwoods, softwoods, plastics and other similar materials. Includes two glue sticks.
specification
Model no: ………………………………………………………AK292.V3
Power:…………………………………………………………………..40W
Supply:…………………………………………………………………230V
Consumables: ……AK292/2 All purpose glue stick pack of 25
operation
- WARNING! Remember that whilst operating the gun, both the dispensing nozzle and the glue itself are hot. DO NOT allow the nozzle or glue to come into contact with any part of your body or that of anybody else who may be assisting you.
PREPARATION
- Ensure the work surface is clean and clear before engaging in the task in hand.
- Steady the workpiece with an appropriate vice or clamp.
- Insert the glue stick firmly into the inlet and plug the glue gun into the mains.
USE
- Squeeze the trigger several times to insert the stick into the gun.
- Leave the gun to warm up for approximately 5 minutes.
- Squeeze the trigger firmly until glue flows from the nozzle.
- When the task is complete, unplug the gun and leave to cool.
- No cleaning is required. DO NOT attempt to remove the glue stick from the gun
- as this may cause damage to the product and/or personal injury.
Weee Regulations
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>