2E-OPS-1200 Portable Power Station User Manual

2E-OPS-1200 Portable Power Station

WARNING

1. Please avoid using the product near high temperature, high humidity, direct sun environment and fireplace.
2. Do not disassemble or modify this product, it will cause malfunction and fire.
3. Please discard or recycle the product according to the methods prescribed by local laws.
4. Be careful not to drop the product from a high place and give the product a strong impact.
5. Keep or use the product in a place out of the reach of children.
6. Please use our company’s genuine accessories. The damage caused by the use of non-genuine accessories cannot be repaired free of charge.
7. Please leave a space of about 30cm away from the side suction and exhaust ports, so as not to affect the heat dissipation of the product.
8. When not using this product, please turn off the power and unplug the power cord. Please avoid storing the product in a place exposed to direct sunlight with high temperature and humidity.
9. For long-term storage, please consume power from full power to no power once every 3 months, and then recharge to about 50%.
10. Please do not use this product and its accessory cables and connecting equipment when there is a defect.

Please do not store the product for a long time in extremely high and low temperature places such as in the car and in the field warehouse to avoid shortening the battery life.

Packing List

Product introduction

1. Hand shank

2. 15W Wireless Charging

3. 12V Cigar lighter (Female)

4. LED On/Off Power Button

5. Main On/Off Power Button

6. Led Screen Display

7. AC On/Off Power Button

8. VDE(Europe) Socket Output (AC230V/50Hz)

9. DC On/Off Power Button
   9.2 DC5.5*2.1 Output

10. Anderson Port for Solar Charging

11. DC7.9 Input only

12. USB Port / Wireless Charging ON/OFF Button
    12.2. Type-C1 Input/Output PD100W
    12.3. Type-C2 Output PD100W only

13. LED Torch

14. Type-C1 Input/Output, no need to do any actions, connect your device, the Power Station will be discharged automatically.

15. Press the Light Button (4) for 3-5 seconds, the lighting will be turned on, click the light button to switch different modes (Weak/ Strong/Blink).

16. The following steps must be turned on the Power Station: Press Power Button (5) for 3-5 seconds
    a. When the Screen is lighted on, Press the USB Power button (12.1) to turn on the Type-C2+4USB-A+Wireless output.
    b. Press the DC button (9.1) (till LED for DC is lighted on), then 3DC5.5(at the bottom of the screen) and 2*12V Car outlet (at the top of the screen) can be output.
    c. Press the AC Power Button (7)for 3-5seconds,the Screen show moment Voltage 230V means AC Socket can be output. Press AC Power Button again for 3-5seconds to cut off the AC Output(the LED for AC was turned off).

Notice:

1. It is recommended that the loaded device should not exceed 1200W, and the excessive power may cause output protection or burn out the product.
2. Only Anderson Port for Solar Charging
3. The Cooling Fan will be started when the total output Power >=150W(1pc), Power >=300W(2pcs)
4. USB-A QC3.0-18W have no output when DC Charging Input
5. DC input will be cut off @85% battery level when DC+PD Input same time
6. 3DC5.5 and 2Car Outlet have no output when DC7.9 Input
7. DC Output will be cut off when AC Output reached 1000W

Technical Specification

OUTPUT

AC OUTPUT| Rated Voltage| 230 V
Rated Power| 1200 W/1080 Wh
Peak Power| 2400 W @1s
Over Load| 1300 W @10s
Frequency| 50 Hz
DC12V OUTPUT| DC5.52.1-1/2/3| 12 -13 V/10 A(Share)
Car Cigar Lighter| 12 -13 V/10 A(Share)
3DC5.52.1 Output and 2 Car Cigar Lighter share 12 -13 V/10 A
TYPE-C OUTPUT| Type-C1| PD100W
Type-C2| PD100W
USB-A OUTPUT| USB-A1/A2| 5 V/3 A, 9 V/2 A, 12 V/1.5 A
USB-A3/A4| 5 V/2.1 A
Wireless Output| Rated Power| 5 W/7.5 W/10 W/15 W (Max.)
Operation Frequency| 110-205 KHz
The maximum intensity of the transmitter’s magnetic field at a distance of 10 m| 66 dBμA/m
Software| V 2.0
LED LIGHT| Power 12W(Max.)/1320-1600 Lums Continuous lighting 90H
Lighting (Weak/Strong) / SOS (Quick/Slow Flash)
INPUT
INPUT| DC7.90.9: 5-28 V/6 A, 168 W (Max.)
Anderson Port: for Solar Charging Only 120 W (Max.)
Type-C1: PD100 W (Max.)
Support Type-C+DC Input 268 W (Max.)
BATTERY
1080 Wh/300000 [email protected]
SIZE/N.W
338.1247245.1 mm/11.60 KG

UPS mode

UPS function

This product has the bypass mode, does not need to pass through the battery, can directly output from the AC.

In UPS mode, when the AC input power of the mains is cut off due to a power outage, the AC input power of the mains can be used in about automatic switch to product battery power within 10 ms to ensure AC output.

UPS Connections

As shown in the figure below, connect the product between the socket on the wall and the electrical appliances, and the power of the product is in the ON state. When you turn on the power of the electrical appliances, it will directly uses the AC power of the power grid.
In this state, when the power grid is cut off, it will automatically switch to the product’s internal battery to supply power.

Solar panel connection

Our products can be connected to solar panels and can be charged through solar panels.

Solar panel input can be the most maximum 120W.

• Solar panel charging power, according to the weather and climate conditions.
• Only Anderson Port for Solar Charging

Connecting Pattern

Car charging

This product can be charged by the cigarette lighter in the car with an DC cable or PD Cable.

Connect Car Charger to the cigarette lighter in the car and the DC5.5 port OR Type-C port on the side of the product, turn on the engine of the car, and the LED of this product will show the input power.

• On-board charging should be carried out with the car engine turned on. If the engine is not turned on, the battery might run out.

Warranty Card

This product provides a 12-month warranty service from the date of purchase

• If there is a quality problem within the range of normal use, we provide warranty service.
• After purchasing our company’s products, please keep this product together with invoices and other items. When maintenance services are needed, please provide information according to our company’s request.
• In the case where the warranty is damaged or altered, and no stamp of the sales store on the warranty, the warranty service may be not be provided.
• Damage causes by use beyond the normal range of use is not covered by the warranty service.
• The content of the warranty scope shall be subject to the content recognized by the company.
• Even within the scope of the warranty, sometimes it will be exchanged for products with the same function. The shipping and repair fees for products outside the warranty range shall be paid by the customer.
• Sometimes the specifications and functions of the product will be updated without prior notice.

References

• Сервіс Центр

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>