GRS Viper SBC Build A Cade Instruction Manual

September 2, 2024
GRS

GRS Viper SBC Build A Cade

GRS Viper SBC Build A Cade

What is needed

  • Build-A-Cade Full kit
  • GRS Viper SBC with WIFI antenna installed
  • GRS Viper SBC IO cable
  • GRS Viper DSI cable
  • GRS Viper Fixing plastic bracket
  • GRS Viper OTG cable
  • GRS BAC hand screws kit
  • GRS BAC Brass screw kit
  • GRS BAC HDMI cable for Pi4/Viper

What is needed

Step by Step Guide

  1. Attach RUBBER FEET (Q) to designated marks on the BOTTOM (K1), ensuring the wire is positioned at the rear right. The arrow on K1 indicates the front. Secure the BATTERY (N) onto the BOTTOM (K1) with a BATTERY STRAP (K2) and two M3x8mm self-tapping screws (S6). Set aside.
    Step by Step Guide

  2. Fasten the MicroSD card connector to the BACK PANEL (L1) using two M2.3x6mm screws (S4). Set aside.
    Step by Step Guide

  3. Position the screen on top the Screen Mount (F2).
    Step by Step Guide

  4. While holding the screen to prevent it from falling, flip to the other side and secure using M2.5x5mm screws (S3) into the Screen Mount (F2).
    Step by Step Guide

  5. Flip again, so the screen faces up, and place the Screen Bezel (F1) over it.
    Step by Step Guide

  6. Flip back to have the Screen PCB facing up and fix the Screen Bezel (F1) in place with four M2.3x6mm screws (S4).
    Step by Step Guide

  7. Secure the GRS Viper fixing bracket with a screw.
    Step by Step Guide

  8. Apply plastic double-sided screws from the brassscrew kit to the PCB treaded studs on the screen.
    Step by Step Guide

  9. Connect the GRS Viper SBC dedicated DSI cable to the screen’s FPC connector, ensuring it locks in place.
    Step by Step Guide

  10. Attach the other end of the DSI cable to the Viper SBC’s FPC connector, securing it with the lock.
    Step by Step Guide

  11. Place the GRS Viper SBC atop the screen’s PCB, securing one end with the fixing bracket.
    Step by Step Guide

  12. Use brass screws to fasten the Viper SBC to the screen mount assembly.
    Step by Step Guide

  13. Connect the Viper IO cable for Build-A-Cade to the 40-pin connector on the Viper SBC, aligning the red cable towards the power socket as shown in the diagram.
    Step by Step Guide

  14. Place the left side (A) on a flat surface and slide the screen assembly into its slot.
    Step by Step Guide

  15. Fit the control panel assembly (B) into its designated position as illustrated.
    Step by Step Guide

  16. Remove the headphone jack cover, set the COIN DOOR (C2) into the FRONT (C1) from the bottom, then press the top into place, avoiding pinching the rubber jack cover.
    Step by Step Guide

  17. Insert the front and coin door assembly into its slot.
    Step by Step Guide

  18. Peel off the protective film from both sides of the ACRYLIC MARQUEE (O) and assemble by positioning the BOTTOM MARQUEE CHANNEL (D), TOP MARQUEE CHANNEL (E), and ACRYLIC MARQUEE (O) as indicated.
    Step by Step Guide

  19. Remove the protective film from the ACRYLIC BEZEL (P) and slide it into the slots on the CONTROL PANEL (B) and SCREEN BEZEL (F1), directly in front of the screen.
    Step by Step Guide

  20. Place the RIGHT SIDE (K) on top, ensuring all parts align and fit into place.
    Step by Step Guide

  21. Slide the BOTTOM (K1) into its tracks, arrow pointing front, and stand the assembly upright.
    Step by Step Guide

  22. Slide the TOP (H) into its tracks, arrow pointing front.
    Step by Step Guide

  23. Connect the 14-pin connector from the WIRING HARNESS to the CONTROL PANEL ASSEMBLY (B).
    Step by Step Guide

  24. Move all wiring to the top of the cabinet and insert the CENTER BRACE (J) into its tracks, sliding it forward with the opening at the back.
    Step by Step Guide

  25. Connect the 8-pin connector from the WIRING HARNESS (W1) to the COIN DOOR (C2).
    Step by Step Guide

  26. Connect all side-mounted cables to the GRS Viper SBC, including audio (W3), OTG cable, and HDMI.
    Step by Step Guide
    Step by Step Guide
    Step by Step Guide

  27. Insert the USB EXTENSION (W4) into the USB port(s) on the GRS Viper SBC.
    Step by Step Guide

  28. Route the 2-pin connector and wires from the WIRING HARNESS through the LED PANEL (I) opening and connect to the LED board. Slide the LED PANEL (I) into its tracks. Secure the HDMI port to the BACK PANEL (L1) with two M3x8mm screws (S5).
    Step by Step Guide

  29. Connect the USB POWER CABLE (W2), main WIRING HARNESS (W1), and USB EXTENSION (W4) to the back panel circuit board.
    Step by Step Guide

  30. Insert the MicroSD card extension cable (L2) into the GRS Viper SBC.
    Step by Step Guide

  31. Arrange all wiring neatly and fasten the BACK PANEL (L1) to the cabinet using six M3x8mm screws (S5) or hand screws.
    Step by Step Guide

  32. Install the joystick ball top by pressing it onto the plastic handle on the BACK PANEL ASSEMBLY (L1).
    Step by Step Guide

  33. Slide the joystick DUST COVER (B2) over the metal shaft, and affix the BALL TOP (B1) by pressing it onto the shaft.
    Step by Step Guide

  34. Slide the joystick DUST COVER (B2) over the metal shaft, and affix the BALL TOP (B1) by pressing it onto the shaft.
    Step by Step Guide

  35. With the power switch in the OFF position, insert the Raspberry Pi™ power adapter (not included) into the USB-C port on the rear of the BUILD-A-CADE cabinet. Charge the battery fully, removing it from power once charged for optimal performance. Charging while using the device is possible.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals