SANTOS 408.007 Novo Citrus Juicer User Manual

: June 4, 2024
: SANTOS

Table of Contents

SANTOS 408.007 Novo Citrus Juice
“CE/UE” COMPLIANCE DECLARATION
IMPORTANT SAFEGUARDS
YOUR CITRUS JUICER Nos. 11- 38 – 52
Using the CITRUS JUICER
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
Documents / Resources

SANTOS 408.007 Novo Citrus Juice

SANTOS 408.007 Novo Citrus Juicer-fig1

IMPORTANT: documents included in this manual to be kept:

“CE” COMPLIANCE DECLARATION
WARRANTY CERTIFICATE

SANTOS 408.007 Novo Citrus Juicer-fig1

“CE/UE” COMPLIANCE DECLARATION

SANTOS 408.007 Novo Citrus Juicer-fig8

IMPORTANT SAFEGUARDS

When using, cleaning or maintaining the machine, always follow these instructions: Read all instructions

Note: You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual.

IMPROPER USE

Do not use this appliance to press any food other than limes, lemons, oranges and grapefruit.
Cleaning in a jet of water or a high pressure spray is prohibited.
The base must not be immersed in water.
Never use the appliance if the power cord is damaged. It must be replaced by either a SANTOS approved dealer or a person with similar qualifications to avoid any danger.
The appliance must be unplugged before any intervention on it: cleaning, general care, maintenance.
It is forbidden to operate the appliance on a surface with a slope in excess of 10° with respect to the horizontal plane. The feet of the machine must always be resting on this surface.
The use of spare parts other than certified original SANTOS parts is prohibited
Never connect several appliances to the same power socket.
Never use the machine outdoors.
Never place the appliance close to or on a source of heat.
This appliance is a professional machine designed exclusively for professional use. It is not designed for household use.
This appliance is not designed for use by people (including children) whose physical, sensorial or mental capacities are impaired or by people with no experience or knowledge, unless they have been supervised or given training in the use of the appliance beforehand by a person responsible for their safety. Supervise children to ensure they do not play with the appliance.
This appliance is intended for use in communal areas, e.g. in the kitchens of restaurants, canteens, hospitals and artisan trades such as bakeries, butcher’s shops, etc., but not for continuous mass production of food.

ELECTRICAL CONNECTION:
The appliance is available in with a choice of two voltages for the power supply

220-240V 50/60 Hz single phase
110-120V 50/60 Hz single phase
Note: This appliance can operate at both 50Hz and 60Hz without any adjustments. Line protection: the appliance should be connected to a standard 2-pole + earth electric socket. The installation should be fitted with an RCD and a fuse rated at 16A. The appliance must be earthed

CARE:

Before connecting the machine, check that the mains electrical voltage is the same as the voltage for your appliance. Its value is shown:
- either on the identification plate under the machine.
- or on the identification plate on the last page of this manual.
If the power cable is damaged, it should be replaced by a SANTOS approved dealer, SANTOS or a person with similar qualifications to avoid any danger.
CARE: Make sure that the on / off switch (6) is on 0 position before plugging the power cord (7) into the mains supply socket (Fig.A).

USING FOR THE 1st TIME:

Carefully clean all parts of the machine in contact with the food (Fig. A).

Remove the anti-splash dome (8) {model no 52}.
Remove the cone (1) by pulling it upwards.
Remove the bowl (2), the pulp grating (9) {model no 52} and the trim (3) {model nos. 11 and 38}.
Wash the parts with a standard washing up liquid or in the dishwasher.

RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE

This equipment is marked with the selective sorting symbol relating to wastes from electrical and electronic equipment. It signifies that this product should be taken over by a selective collection system conforming to the Guideline 2012/19/EU (WEEE) – part Professional Equipment – so that it can be either recycled or dismantled in order to reduce any impact on the environment.

For more information, please contact your Retailer or the SANTOS.
For eliminating or recycling components of equipment, please contact a specialized company or contact SANTOS.
The electronic products not undergoing a selective sorting are potentially dangerous for the environment.
The damaging materials should be eliminated or recycled according to the regulations in force.

YOUR CITRUS JUICER Nos. 11- 38 – 52

Citrus juicers nos. 11 – 38 – 52 are especially designed for bars, cafés, hotels, restaurants, cocktail bars, institutions, fresh fruit juice bars, etc.
The appliances nos. 11 and 38 are comprised of an aluminum motor unit, a juice bowl and 3 engineered plastic pressing cones (2 pressing cones for model N°38).
The appliance no. 52 is comprised of an aluminum motor unit, a powerful motor for intensive use, a stainless steel bowl, 3 plastic pressing cones and a plastic anti-splash dome.
Citrus juicers nos. 11 – 38 – 52 are designed to press limes, lemons, oranges or grapefruit.
They are ideal for preparing: fresh lemon, orange or grapefruit juice or as a basis for preparing fruit cocktails.

Using the CITRUS JUICER

USING:
Caution: the fruits used must be washed carefully before being pressed.

Assembly and preparation:

Place the trim (3) on the bowl (2) {models nos. 11 and 38}.
Place the bowl (2) on the base (4).
Place the pulp grating (9) in the bowl.
Place the cone (1) on the motor shaft (5).
Place the anti-splash dome (8) on the bowl (2) {model no 52}.
Cut the citrus fruit in two halves.
Place a glass level with the spout on the bowl (2).
Start the appliance by putting the On / Off switch (6) on “1”.
Press the citrus fruit halves one after the other.
When you have finished using it, stop the appliance by putting the On / Off switch (6) on “0”.

CLEANING:

IMPORTANT :
In every case, stop the appliance and unplug the appliance’s power cord (7).

It is recommended to clean the appliance as soon as you have finished using it. Cleaning will be easier if you do not wait until the pulp has dried in the bowl (2), on the anti-splash dome (8), the cone (1) or the pulp grating (9). The base (4) is to be cleaned with a soft damp sponge, then dried. Washing the trim (3) in the dishwasher will cause tarnishing. You are advised to wash it with soapy water.

MAINTENANCE

Before any servicing of the appliance, it is essential to unplug the appliance from the mains supply (7). This machine requires no particular maintenance because the bearings are lubricated for life. If servicing is necessary to replace any parts such as the electrical components or any others, refer to the list of components (see the exploded view at the end of the manual).

Spare parts
IMPORTANT: Use of spare parts other than certified original SANTOS parts is prohibited

For all spare part orders (see references in the exploded view at the end of the manual), state:

the type,
the machine serial number and
the electrical specifications (16)
recorded under the machine.

Prolonged periods of non-use:
There are no problems with this appliance in the event of prolonged periods of non-use. You are simply advised to clean it before use and check that the components of the appliance are in good condition (e.g. power cord, seals and other spare parts).

TROUBLESHOOTING

Identifying the cause of appliance stoppage precisely.

The appliance does not start:
Check: the mains supply, the condition of the power cord (7).

The appliance stops due to motor overheating:
(the motor unit is hot) The motor is protected by a built-in thermal cutout. In the event of overheating, the motor stops.

Set the On / Off switch (6) to 0 position, disconnect the plug (7).
Wait until the motor cools down (20 to 45 minutes), reconnect the plug (7) then press the On / Off switch (6) (position 1).
If the problem persists, switch off the power supply to the appliance (unplug the cord from the mains socket (7)) and call in the maintenance service or contact a SANTOS-approved dealer.
The appliance stops further to an overload:
If the motor stalls (due to excessive pressing), it can heat very quickly and stops by overload protection.

TECHNICAL SPECIFICATIONS

Model		N° 11	N° 38	N° 52

Supply voltage

Frequency

| (V)

(Hz)

| 220-240 100-120

50/60 50/60

| 220-240 100-120

50/60 50/60

| 220-240 100-120

50/60 50/60

Motor: Nominal Power input Speed :| ****

(W)

(rpm)

| ****

130 155

1450 to 50Hz

1700 to 60Hz

| ****

130 155

1450 to 50Hz

1700 to 60Hz

| ****

230 260

1450 to 50Hz

1700 to 60Hz

Operating modes (3)| | intermittent cycle

5 min ON / 5 min OFF

| intermittent cycle

5 min ON / 5 min OFF

| Continuous
Dimensions : Height

Width

Depth Clearance height beneath the spout

Weight: Net weight Packaged weight

Noise: (2)

| (mm)| 350| 350| 480
(mm)| 200| 200| 230
(mm)| 300| 300| 300
(mm)| 125| 135| 200
(kg)| 5| 5| 10
(kg)| 5.6| 5.6| 11
(dBA)| 65| 65| 65

These ratings are provided as a rough guide. The exact electrical specifications can be found on the rating plate.
Noise level measured in sound pressure appliance in operation 1 m from its axis in accordance with standard EN 31201.
5min / 5min cycle: The professional appliance is intended for intermittent use according to a 5 minutes ON and 5 minutes OFF cycle. This cycle corresponds to the operating time to perform the function and the stopping time for the preparation and serving of the products processed, in compliance with the instructions of the standard: EN 60335-2-64+A1:2004, Particular requirements for commercial electric kitchen machines.

MARK

|

Description

---|---
1| Pressing cone
2| Bowl
3| Trim
4| Base
5| Motor shaft
6| On / off switch
7| Plug / power supply cord
8| Anti-splash dome
9| Pulp grating

ELECTRICAL WIRING DIAGRAMS

Models nos. 11 and 38:

Wiring diagram 220-240V 50/60Hz

SANTOS 408.007 Novo Citrus Juicer-fig3