SelectBlinds Precision Dual Roller Shades Installation Guide

SelectBlinds Precision Dual Roller Shades

Product Information

This product is a window covering system that operates with a continuous chain. It is designed for indoor use only and can be assembled by non- professionals.
The product comes with installation brackets and a child safety device to prevent strangulation and entanglement.

Product Usage Instructions

1. Before starting the installation, carefully read and understand the instructions provided.
2. Ensure that the product is suitable for your window type (inside mount or outside mount).
3. Step One: For both the inside mount and the outside mount, make sure the brackets are level with each other. This is crucial for the shade to operate properly.
4. Step Four: Follow the provided diagram to properly attach and secure the brackets to the window frame.
5. Step Seven: Once the brackets are securely installed, attach the shade to the brackets. Refer to the diagram for proper alignment.
6. Step Nine: Install the child safety device as specified in the childsafe manual. This will help prevent accidents involving the cords.
7. Final Step: Make sure the child safety device is properly installed. Test the shade’s operation to ensure it is functioning correctly.
8. Removal: If you need to remove the shade, follow the reverse steps of the installation process.

For the Fascia Dual Roller with Motorization variant, please refer to the separate installation manual provided for specific instructions on installation and usage.
Please note that it is important to always prioritize safety when using this product, especially when there are young children around. Keep cords out of their reach and avoid tying cords together to prevent strangulation and entanglement.

Installation – Day/Night with Continuous Chain

Read the instructions carefully before assembling and using the product. The assembling process can be completed by non-professionals. For indoor use only.

WARNING

• Young children can strangle in the loop of pull cords, chains and tapes, and cords that operate window coverings.
• To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become wrapped around a child’s neck
• Move beds, cots, and furniture away from window-covering cords.
• Do not tie cords together.
• Make sure cords do not twist together and form a loop.

Step One:

• Attach the upper set of end caps before installing the brackets
• Align the pins on the inside of the end cap with the holes on the brackets as shown and press together

Step Two:

• Use the brackets to mark the screw locations
• On the outside mount, make your marks so the distance from the outside edge of the bracket to the outside edge of the other bracket equals your ordered width
• Note: Brackets must be level with each other for the shade to operate properly (for both inside mount and outside mount).

Step Three:

• The idle side attachment should be on the bracket opposite of the chain on the shade
• Simply click into the bracket if it is not already attached

Step Four:

• Slide the idle side of the shade onto the idle pin
• Note: The end plug is already installed on the idle side in the tube of the shade

Step Five:

• Click the control side of the shade into the bracket

Step Six:

• Adjust the clutch so the chain points to the front to allow clearance to install the bottom/back shade
• The idle side attachment should be on the bracket opposite of the chain for the bottom/back shade (simply click into the bracket if it is not already attached)

Step Seven:

• Slide the idle side of the shade onto the idle pin
• Note: The end plug is already installed on the idle side in the tube of the shade

Step Eight:

• Click the control side of the shade into a bracket

Step Nine:

• Attach the lower set of end caps to the brackets

WARNING

• Install the child safety device as specified in the childsafe manual.

Final Step:

• Install the child safety device

Removal

Installation – Fascia: Day/Night with Chain
Read the instructions carefully before assembling and using the product.
The assembling process can be completed by non-professionals. For indoor use only.

Installation – Fascia Dual Roller with Motorization
Read the instructions carefully before assembling and using the product.
The assembling process can be completed by non-professionals. For indoor use only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>