TOTOLINK LR350 4G LTE Router Installation Guide
- June 12, 2024
- TOTOLINK
Table of Contents
The Smartest Network Device
Quick Installation Guide
4G LTE Router
Model: LR350
Copyrights © TOTOLINK. All Rights Reserved. http://www.totolink.net
Information in this document is subject to change without prior notice
Installation Diagram
Method 1: Wireless Connection to the Internet(with SIM card)
- Insert the SIM car into the slot.
- Power on the router.
- Find the default Wi-Fi name on your Phone and choose to connect. Now, you could enjoy Wi-Fi.
- For security, please follow the below instructions to create passwords for your router and Wi-Fi.
Note: Micro or Nano card must be turned into the SIM card by using the standard SIM card adapter.
Method 2: Wired Connection to the Internet(with Cable)
Default Wi-Fi Name: TOTOLINK_LR350
Configure the Router on Phone
- Activate the WLAN function on your Phone and connect to TOTOLINK_LR350. Then run any Web browser and enter http://itotolink.net in the address bar. (P1)
- Enter admin for the password and then click LOGIN.(P2)
- Click Quick Setup on this page, then enter the setting interface. (P3)
- Time Zone setting. According to your location, please click the Time Zone to choose a correct one from the list, then click Next. (P4)
- Internet Setting. Choose a suitable connection type from the list and fill in the information required, then click Next. (P5/P6)
- Wireless Setting. Create passwords for 2.4G and 5G Wi-Fi (Here users could also revise the default Wi-Fi name) and then click Next. (P7)
- For security, please create a new Login Password for your router, then click Next. (P8)
- The coming page is the Summary informationfor your setting. Please remember your Wi-Fi Name and Password, then click Done. (P9)
- It takes several seconds to save the settings and then your router will restart automatically. This time your Phone will be disconnected from the router. Please back to the WLAN list of your phone to choose the new Wi-Fi name and input the correct password. Now, you could enjoy the Wi-Fi.(P10)
| Connection Type | Description |
|---|---|
| Static IP | Input the IP address, Subnet Mask, Default Gateway, DNS from your |
ISP.
Dynamic IP| No information required. Please confirm with your ISP if Dynamic
IP is supported.
PPPoE| Input User Name and Password from your ISP.
(P6)
FAQs (Frequently Asked Questions)
1. Unable to open the router's login page on the browser?
Please check if your Phone has connected to the router and make sure you have entered the correct default gateway http://itotolink.net
2. After the SIM card is plugged in, the SYS LED on Red Blinking, the Internet cannot be accessed.
In this case, the SIM card is not inserted properly. The solution is to power off the 4G router and re-insert the card. Because the card slot is deep and the fingernails are short, it is recommended to insert the card together with toothpicks; the other case is SIM If the card is not activated, you must insert the card after activation according to the instructions of the card manual.
3. After the SIM card is plugged in, the SYS LED on Red light is always on, the Internet cannot be accessed.
First use the mobile phone card to plug in the router to confirm whether it can be used. If the mobile phone card can be used normally, then ask the 4G SIM card provider if there is any traffic, whether the real-name authentication is verified and whether the card is locked.
4. After the card is used, the mobile phone is connected to Wi-Fi, and the network speed is slow.
This situation is related to the card signal. Where the signal is poor, the corresponding Wi-Fi is not ideal. To debug the routing position, place it in a place with strong signal.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
Manufacturer: ZIONCOM ELECTRONICS (SHENZHEN) LTD.
Address: Room 702, Unit D, 4 Building Shenzhen Software Industry Base, Xuefu
Road, Nanshan District, Shenzhen, Guangdong, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>